journal article·2025-04Open access

Deterioration mechanism of impact toughness in the coarse-grained heat-affected zone of Ca-treated shipbuilding steel plate with high-Cr content

Tingting Li, Jian Yang, Yinhui Zhang, Han Sun, Pengfei Hu, Longyun XU

Abstract

The deterioration mechanism of low-temperature toughness in the coarse-grained heat-affected zone (CGHAZ) of shipbuilding steel plates with Ca-treatment, induced by the addition of Cr, was systematically investigated. Through a combination of experimental research and theoretical calculations, the effects of Cr content (ranging from 0.019 to 0.17 wt%) on microstructural evolution , M 3 C carbide formation, fracture morphology , and low-temperature impact toughness in the CGHAZ were evaluated. The mechanisms responsible for the decline in impact toughness in 170Cr (ω Cr =0.17 wt%) steel have been clarified. Thermodynamic calculations and in situ observations reveal that increasing Cr content reduces the C diffusion coefficient and the austenite-to-ferrite (γ→α) phase transformation temperature. Consequently, there is a decrease in the content of intragranular acicular ferrite (IAF) and an increase in the formation of brittle microstructures within the CGHAZ. It is effectively interpreted by first-principle calculations that the formation energy of M 3 C carbides is reduced when Fe atoms in Fe 3 C are replaced by Cr. The formation energy of Fe 3 C (−0.0487 eV/atom) is greater than that of (Fe, Cr) 3 C (−0.1048 or −0.1111 eV/atom), indicating that the M 3 C type carbides are easier to form in 170Cr steel. In 170Cr steel, strip M 3 C carbides are prone to forming at sub-grain boundaries, weakening the bonding force between sub-grains and making these boundaries more susceptible to crack propagation . Besides, the reduction in the variety of bainite variants decreases the content of high-angle grain boundaries (HAGBs) in bainites, further reducing the crack propagation resistance of 170Cr steel. Furthermore, the increasing C supersaturation in the ferrite of 170Cr steel reduces the plasticity of the CGHAZ, thereby reducing crack initiation energy. In conclusion, the addition of Cr results in a decrease in the low-temperature impact toughness of CGHAZ. As the Cr content increases from 0.019 wt% to 0.17 wt%, the low-temperature impact toughness at −40°C declines from 226 J to 121 J.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Material Properties and Failure Mechanisms · Corrosion Behavior and Inhibition · Fatigue and fracture mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. Effects of Mn and Al on acicular ferrite formation in SAW weld metal10.2355/isijinternational.ISIJINT-2020-407 ↗
2. Transformation behavior of a Ti–Zr deoxidized steel: microstructure and toughness of simulated coarse grain heat affected zone10.1016/j.msea.2013.11.028 ↗
3. Effect of welding heat input on microstructure and toughness of heated-affected zone in steel plate with Mg deoxidation10.1002/srin.201700157 ↗
4. Nucleation effect of Ca-oxysulfide inclusions of low carbon steel in heat affected zone by welding10.4028/www.scientific.net/MSF.941.130 ↗
5. In-situ observation of grain refinement in the simulated heat-affected zone of high-strength low-alloy steel by Zr-Ti combined deoxidation10.1007/s12540-016-5301-9 ↗
6. Improved toughness of weld fussion zone by fine TiN particles and development of a steel for large heat input welding10.2355/tetsutohagane1955.61.11_2589 ↗
7. Super high HAZ toughness technology with fine microstructure imparted by fine particles
8. High tensile strength steel plates and welding consumables for architectural construction with excellent toughness in welded joint JFE EWEL technology for excellent quality in HAZ of high heat input welded joints
9. Excellent heat affected zone toughness technology improved by use of strong deoxidizers
10. Improvement of impact toughness of the welding heat-affected zone in high-strength low-alloy steels through Ca deoxidation10.1007/s11661-020-06105-4 ↗
11. The effect of Ca content on the formation behavior of inclusions in the heat affected zone of thick high-strength low-alloy steel plates after large heat input weldings10.3390/met9121328 ↗
12. Development in oxide metallurgy for improving the weldability of high-strength low-alloy steel—Combined deoxidizers and microalloying elements10.1007/s12613-023-2754-y ↗
13. Effect of B segregation at prior austenite grain boundaries on microstructures and toughness in the heat-affected zone of Mg-deoxidized shipbuilding steel plates10.1002/srin.202200102 ↗
14. Inclusions and microstructures in coarse-grained heat-affected zone of Al-Ti-Ca deoxidized shipbuilding steels with different Al contents after high-heat input welding10.1016/j.jmrt.2024.02.223 ↗
15. Effect of Al content on nanoprecipitates, austenite grain growth and toughness in coarse-grained heat-affected zones of Al-Ti-Ca deoxidized shipbuilding steels
16. Research of microalloy elements to induce intragranular acicular ferrite in shipbuilding steel10.1080/03019233.2017.1405153 ↗
17. Particles, microstructures and impact toughness of CGHAZ of Ca deoxidation shipbuilding steel plates with different Nb contents10.1002/srin.202300020 ↗
18. Microstructure evolution in heat-affected zone of shipbuilding steel plates with Mg deoxidation containing different Nb contents10.1007/s11661-022-06617-1 ↗
19. Effect of Si content on the microstructures and the impact properties in the coarse-grained heat-affected zone (CGHAZ) of typical weathering steel10.1016/j.msea.2019.138082 ↗
20. Precipitate characterisation of an advanced high-strength low-alloy (HSLA) steel using atom probe tomography10.1016/j.scriptamat.2006.12.018 ↗
21. Transition from bainite to acicular ferrite in reheated Fe–Cr–C weld deposits10.1179/026708390790189605 ↗
22. The effect of chromium on the microstructure toughness relationship of C–Mn weld metal deposits10.1016/S1044-5803(01)00168-1 ↗
23. Effect of Cr content on microstructure and impact toughness in the simulated coarse-grained heat-affected zone of high-strength low-alloy steels10.1002/srin.201500424 ↗
24. Effects of dilute substitutional solutes on interstitial carbon in α-Fe: interactions and associated carbon diffusion from first-principles calculations10.1103/PhysRevB.90.024103 ↗
25. First-principles calculations on stabilization of iron carbides (Fe3C, Fe5C2, and η-Fe2C) in steels by common alloying elements10.1007/s11661-012-1229-y ↗
26. The effect of Cr content on intragranular κ-carbide precipitation in Fe-Mn-Al-(Cr)-C low-density steels: a multiscale investigation10.1016/j.matchar.2022.111801 ↗
27. Influence of Cr and Cr+Nb on the interphase precipitation and mechanical properties of V–Mo microalloyed steels10.1016/j.msea.2024.146140 ↗
28. Effect of cerium content on the evolution of inclusions and formation of acicular ferrite in Ti-Mg-Killed EH36 steel10.3390/met10070863 ↗
29. Effect of Mg treatment on refining the microstructure and improving the toughness of the heat-affected zone in shipbuilding steel10.3390/met8080616 ↗
30. Effect of post-weld tempering on the microstructure and mechanical properties in the simulated HAZs of a high-strength-high-toughness combination marine engineering steel10.1007/s40195-019-00954-8 ↗
31. A novel high nitrogen hot-work die steel 3Cr5Mo2SiVN achieving excellent hardness-strength-toughness balance10.1016/j.matchar.2023.113154 ↗
32. Comparison of X-ray and neutron-diffraction refinements of the structure of cementite Fe3C10.1107/S0365110X64003346 ↗
33. First-principles calculation of carbides in niobium microalloyed medium and high carbon steels
34. J. Ågren. A revised expression for the diffusivity of carbon in binary Fe-C austenite. 1986, 20(11): 1507-1510.10.1016/0036-9748(86)90384-4 ↗
35. Developing 1000 MPa grade LCLA steels through continuous cooling: effects of Cr and cooling rate on bainitic and martensitic transformations10.1016/j.matchar.2022.111859 ↗
36. An empirical model for carbon diffusion in austenite incorporating alloying element effects10.2355/isijinternational.51.1903 ↗
37. Microstructure and high strength–toughness combination of a new 700MPa Nb-microalloyed pipeline steel10.1016/j.msea.2007.06.003 ↗
38. Influence of chromium content on the bainite transformation nucleation mechanism and the properties of 800 MPa grade low carbon bainite weld deposited metal10.1016/j.msea.2022.142893 ↗
39. Bainite nucleation mechanism and mechanical properties in low carbon bainite deposited metals with different nickel additions10.1016/j.msea.2022.144036 ↗
40. A comparative study of acicular ferrite transformation behavior between surface and interior in a low C-Mn steel by HT-LSCM10.3390/met11050699 ↗
41. Effect of Nb on microstructure and mechanical properties between base metal and high heat input coarse-grain HAZ in a Ti-deoxidized low carbon high strength steel10.1016/j.jmrt.2022.03.150 ↗
42. Microstructure and fracture characteristics of heat-affected zone in shipbuilding steel plates with Mg deoxidation after high heat input welding10.1002/srin.202100376 ↗