journal article·2024-12

Effect of solution and cooling methods on the high-temperature mechanical behavior of Ti60 alloy

Fuqian Sun, Jiang Li, Tong Wang, E Zhu, Fuguo Li

Publisher page

Abstract

The influence of solution treatment temperature and cooling rate on the mechanical behavior of Ti60 alloy at 600℃ was investigated. Five different solution treatment temperatures and five different cooling methods were used for the Ti60 alloy. The study revealed that, at the same solution treatment temperature the ultimate tensile strength (UTS) and elongation (Z%) of the water-quenched (WQ) microstructure were 32 % and 61 % higher, respectively, compared to the furnace-cooled (FC) microstructure. The WQ microstructure exhibited significantly superior strength and ductility. This phenomenon was primarily attributed to the differences in microstructural morphology caused by varying cooling methods. The effects of different cooling methods on high-temperature tensile behavior were discussed in terms of fracture morphology, high-angle grain boundaries, and void distribution. On the other hand, the UTS of the air-cooled (AC) microstructure initially increased and then decreased with decreasing solution treatment temperature, while the UTS of the FC microstructure decreased with decreasing solution treatment temperature. This phenomenon was mainly due to the competing effects of effective slip length (colony size) and elemental distribution. The correlation between solution treatment temperature and cooling rate parameters and high-temperature mechanical properties was established using the response surface methodology (RSM). The optimized solution cooling scheme was determined to be at 1012℃ with a cooling rate of 4238℃/min.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Intermetallics and Advanced Alloy Properties · Magnesium Alloys: Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (47)

Show source-provided references
1. Advancement in the application of alloys and composites in the manufacture of aircraft component: a review
2. Titanium and titanium alloys
3. Opportunities and issues in the application of titanium alloys for aerospace components10.3390/met10060705 ↗
4. On the characteristics of titanium alloys for the aircraft applications
5. Hot working behavior of near-α alloy IMI83410.1016/j.msea.2004.12.005 ↗
6. Crack growth response of IMI 834 under variable amplitude loading10.1016/S0142-1123(96)00048-5 ↗
7. High-temperature titanium alloys10.14429/dsj.55.1979 ↗
8. High temperature fatigue behavior in tensile hold LCF of near-alpha T i-1100 with lamellar structure10.1023/A:1004627216837 ↗
9. In-situ SEM observations of fracture behavior of BT25y alloy during tensile process at different temperature10.1016/j.matdes.2016.12.050 ↗
10. Nano-precipitation and tensile properties of Ti60 alloy after exposure at 550°C and 650°C10.1016/j.msea.2014.12.031 ↗
11. Fatigue failure mechanism of Ti60 titanium alloy in HCF and VHCF regime at different temperatures10.1016/j.engfailanal.2023.107393 ↗
12. The origin of coarse macro-grain during thermo-mechanical processing in a high temperature titanium alloy10.1016/j.jallcom.2018.10.127 ↗
13. Deformation behavior and microstructure evolution during hot working of Ti60 alloy with lamellar starting microstructure10.1016/j.jallcom.2019.03.345 ↗
14. Effect of different heat treatments on microstructure and mechanical properties of Ti6Al4V titanium alloy10.1016/S1875-5372(17)30109-1 ↗
15. Effect of temperature and cooling rates on the α+β morphology of Ti-6Al-4V Alloy10.1016/j.prostr.2019.07.056 ↗
16. Effect of α′ Martensite on Microstructure Refinement After α + β Isothermal Treatment in a Near-α Titanium Alloy Ti6010.1007/s11665-015-1486-1 ↗
17. Influence of thermal treatment on element partitioning in α+β titanium alloy10.1016/j.jallcom.2019.03.332 ↗
18. Effects of heating rate on the alloy element partitioning and mechanical properties in equiaxed α+β Ti-6Al-4V alloy10.1016/j.jmst.2021.02.061 ↗
19. Effect of Solutioning Conditions on Aging Response in Ti–15V–3Cr–3Sn–3Al10.2320/matertrans1989.34.373 ↗
20. Precipitation behaviour during the β→α/ω phase transformation and its effect on the mechanical performance of a Ti-15Mo-2.7Nb3Al-0.2Si alloy10.1038/s41598-019-54114-0 ↗
21. Effects of initial microstructures on hot tensile deformation behaviors and fracture characteristics of Ti-6Al-4V alloy10.1016/j.msea.2017.11.044 ↗
22. Influence of solution treatment on microstructure and mechanical properties of a near β titanium alloy Ti-733310.1016/j.matdes.2015.06.015 ↗
23. Effect of primary α phase fraction on tensile behavior of IMI 834 alloy10.1016/j.prostr.2019.05.011 ↗
24. β phase transformation kinetics in Ti60 alloy during continuous cooling10.1016/j.jallcom.2013.04.117 ↗
25. Tuning the scale of α precipitates in β-titanium alloys for achieving high strength10.1016/j.scriptamat.2018.05.040 ↗
26. Influence of cooling rate and aging on the lamellar microstructure and fractography of TC21 titanium alloy10.1007/s13632-012-0055-3 ↗
27. Microstructure evolution and mechanical properties of near-α Ti-8Al-1Mo-1V alloy at different solution temperatures and cooling rates10.1016/j.jallcom.2017.08.165 ↗
28. A parametric study on the design factors influencing the thermal performance of nickel alloy C263 sandwich panels10.1080/14484846.2021.1876601 ↗
29. Optimum surface roughness prediction for titanium alloy by adopting response surface methodology10.1016/j.rinp.2017.02.027 ↗
30. Surface roughness prediction of flow-formed AA6061 alloy by design of experiments10.1016/j.jmatprotec.2007.08.065 ↗
31. Simultaneous optimization of several response variables10.1080/00224065.1980.11980968 ↗
32. Mechanical properties of alloys consisting of two ductile phases10.1016/j.pmatsci.2005.10.003 ↗
33. Effect of retained beta layer on slip transmission in Ti–6Al–2Zr–1Mo–1V near alpha titanium alloy during tensile deformation at room temperature10.1016/j.matdes.2013.12.018 ↗
34. Hot deformation behavior of Ti-6Al-4V alloy: Effect of initial microstructure10.1016/j.jallcom.2017.05.097 ↗
35. Analysis of slip activity and heterogeneous deformation in tension and tension-creep of Ti–5Al–2.5Sn (wt%) using in-situ SEM experiments10.1080/14786435.2012.682174 ↗
36. Origins of different tensile behaviors induced by cooling rate in a near alpha titanium alloy Ti6510.1016/j.mtla.2018.06.005 ↗
37. , Twinning, and fracture in hexagonal close-packed metals10.1007/BF02648537 ↗
38. In-situ investigation on tensile deformation and fracture behaviors of Ti60 alloy rolled sheet with equiaxed microstructure10.1016/j.jallcom.2022.166464 ↗
39. Analysis of the different slip systems activated by tension in a α/β titanium alloy in relation with local crystallographic orientation10.1016/j.actamat.2004.09.040 ↗
40. High-cycle fatigue crack Initiation and growth in TIMETAL LCB10.1361/105994905X75592 ↗
41. Micromechanical analysis of the yielding behavior of individual Widmanstätten colonies of an α+β titanium alloy10.1007/s11661-004-0177-6 ↗
42. Influence of cooling rate following heat treatment on microstructure and phase transformation for a two-phase alloy10.1016/j.jallcom.2016.07.107 ↗
43. Influence of processing on microstructure and mechanical properties of (α+β) titanium alloys10.1016/S0921-5093(97)00778-8 ↗
44. Influence of alloy element partitioning on strength of primary α phase in Ti-6Al-4V alloy10.1016/j.jmst.2017.07.016 ↗
45. Role of microstructure in plastic deformation and crack propagation behavior of an α/β titanium alloy10.1016/j.vacuum.2020.109848 ↗
46. Improvement of the crack propagation resistance in an α + β titanium alloy with a trimodal microstructure10.3390/met10081058 ↗
47. Optimization of dead metal zone to reduce cutting forces in micro milling of Inconel 718 using RSM