journal article·2024-12

Achieving high-strength, high-porosity and relatively low-shrinkage in extrusion-based 3D printed ZrO2 ceramics by adjusting CaCO3 addition and sintering temperature

Yuxiao Lin, Fuchu Liu, Liang Zhang, Yi Wang, Miao Wang, Yanzhao Li, Ming Wu, Zheng Li, Hao Liu, Guangchao Han

Publisher page

Abstract

High-strength, high-porosity and relatively low-shrinkage ZrO 2 ceramics were successfully fabricated by material extrusion 3D printing technology via optimizing CaCO 3 addition and sintering temperature. The effects of different CaCO 3 additions on the performance, phase formation, and microstructure of porous ZrO 2 ceramics sintered at different temperatures were systematically investigated and discussed. The results showed that flexural strength, porosity and shrinkage of the ZrO 2 ceramics were significantly affected by CaCO 3 addition and sintering temperature. The appropriate addition of CaCO 3 could promote sintering and phase transformation of m-ZrO 2, increase the number and size of pores in the matrix. The corresponding flexural strength and porosity of the sintered samples increased, while the shrinkage rate decreased. The raised sintering temperature appropriately facilitated the formation of CaZrO 3. Microstructural analysis indicated that CaZrO 3 exhibited a larger polyhedral bulk morphology, mainly distributed at the edges of pores, which could stabilize the pore structure and thicken the sintering necks, and thereby exhibiting well-balanced comprehensive performance. The ZrO 2 ceramics with high flexural strength, high porosity and relatively low shrinkage rate were achieved by adding 15 wt% CaCO 3 and sintering at 1450 ℃. The resulting flexural strength and porosity were 27.33 MPa and 67.62 %, respectively, presenting an improvement of 563.35 % and 13.69 % compared to ZrO 2 ceramics without CaCO 3. Moreover, the shrinkage rates in the X-direction (9.98 %), Y-direction (9.62 %), and Z-direction (9.94 %) significantly reduced, decreasing by 38.28 %, 38.10 %, and 41.46 %, respectively.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Injection Molding Process and Properties · Bone Tissue Engineering Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (59)

Show source-provided references
1. Research progress and prospects of colored zirconia ceramics: A review10.26599/JAC.2024.9220941 ↗
2. A review of 3D printed porous ceramics10.1016/j.jeurceramsoc.2022.02.039 ↗
3. Progress, outlook, and challenges in lead-free energy-storage ferroelectrics10.1002/aelm.201900698 ↗
4. Recent advances in ink-based additive manufacturing for porous structures
5. Achieving ultrahigh energy storage density in super relaxor BCZT-based lead-free capacitors through multiphase coexistence
6. Bio-inspired metallic cellular material with extraordinary energy dissipation capability10.1016/j.cej.2023.146382 ↗
7. Porous ceramics: Light in weight but heavy in energy and environment technologies10.1016/j.mser.2020.100589 ↗
8. Highly porous zirconia ceramic foams with low thermal conductivity from particle-stabilized foams10.1111/jace.14555 ↗
9. Properties of porous zirconia ceramics fabricated by using various pore-forming agents10.1016/j.ceramint.2022.05.168 ↗
10. Fabrication of porous alumina–zirconia ceramics by gel-casting and infiltration methods10.1016/j.matdes.2014.05.061 ↗
11. Freeze casting: from low-dimensional building blocks to aligned porous structures—a review of novel materials, methods, and applications10.1002/adma.201907176 ↗
12. A review on porous ceramics with hierarchical pore structure by 3D printing-based combined route10.1080/21870764.2021.1981571 ↗
13. Development of Ceramic 3D/4D Printing in China10.1016/j.amf.2024.200158 ↗
14. The applications and latest progress of ceramic 3D printing
15. Lessons from nature: 3D printed bio-inspired porous structures for impact energy absorption–A review
16. Advances on direct selective laser printing of ceramics: an overview10.1016/j.jallcom.2023.172821 ↗
17. Binder jetting 3D printing process optimization for rapid casting of green parts with high tensile strength10.1007/s41230-021-1057-z ↗
18. Enhanced comprehensive properties of stereolithography 3D printed alumina ceramic cores with high porosities by a powder gradation design10.1016/j.jmst.2022.04.040 ↗
19. Fabrication of silica-based ceramic cores with internal lattice structures by stereolithography10.1007/s41230-022-2048-4 ↗
20. 3D printing of ceramics: A review10.1016/j.jeurceramsoc.2018.11.013 ↗
21. 3D printing of thermosets with diverse rheological and functional applicabilities10.1038/s41467-023-35929-y ↗
22. Parameter Optimization via Orthogonal Experiment to Improve Accuracy of Metakaolin Ceramics Fabricated by Direct Ink Writing
23. Material-extrusion based additive manufacturing of BaTiO3 ceramics: from filament production to sintered properties
24. Suitability Analysis for Extrusion-Based Additive Manufacturing Process
25. Direct ink writing: a 3D printing technology for diverse materials10.1002/adma.202108855 ↗
26. Hierarchically porous bone scaffold fabricated via direct foam writing with TCP/ZrO2 composite ink
27. Anisotropic behavior of ZrO2 ceramic fabricated by extrusion
28. Mechanical and dielectric properties of 3D printed highly porous ceramics fabricated via stable and durable gel ink10.1016/j.jeurceramsoc.2019.07.002 ↗
29. Process optimization of porous Al2O3 filter via layered extrusion forming10.1080/10426914.2022.2032143 ↗
30. A polarization double-enhancement strategy to achieve super low energy consumption with ultra-high energy storage capacity in BCZT-based relaxor ferroelectrics10.1039/D4MH00322E ↗
31. Utilizing Domain Engineering to Achieve High-Polarization Relaxor Ferroelectrics for Low-Consumption Ceramic Capacitors10.1021/acs.inorgchem.4c02385 ↗
32. Additive manufacturing of interconnected hierarchically porous zirconia: Utilizing both microspherical and filamentary pore-forming agents via direct ink printing10.1016/j.ceramint.2024.02.054 ↗
33. Effect of CaCO3 addition on thermal shock resistance of MgO-ZrO2 composites10.1016/j.ceramint.2022.08.008 ↗
34. Robocasting of highly porous ceramics scaffolds with hierarchized porosity
35. Color aspect of monolithic zirconia restorations: a review of the literature10.1111/jopr.12906 ↗
36. Parameter Optimization and Precision Control of Water-Soluble Support Cores for Hollow Composite Castings Fabricated by Slurry Microextrusion Direct Forming Method
37. High-strength, high-porosity and low-shrinkage Al2O3 ceramics prepared by flexible adjustment of CaCO3 size and content10.1016/j.jeurceramsoc.2023.11.016 ↗
38. Effect of particle size distribution on the preparation of ZTA ceramic paste applying for stereolithography 3D printing10.1016/j.powtec.2019.09.066 ↗
39. Effects of dispersant concentration on the properties of hydroxyapatite slurry and scaffold fabricated by digital light processing10.1016/j.jmapro.2023.12.040 ↗
40. Sample selection for models to represent ceramic cores fabricated by stereolithography three-dimensional printing10.1016/j.jmst.2021.12.058 ↗
41. Effect of sintering temperature on microstructure and properties of 3D printing polysilazane reinforced Al2O3 core10.1007/s41230-023-2122-6 ↗
42. Additive manufacturing of high solid content lunar regolith simulant paste based on vat photopolymerization and the effect of water addition on paste retention properties
43. Thermal transport and phase transitions of zirconia by on-the-fly machine-learned interatomic potentials10.1038/s41524-021-00630-5 ↗
44. Synthesis and properties of novel calcia-stabilized zirconia (Ca-SZ) with nano calcium oxide derived from cockle shells and commercial source for dental application10.3390/app10175751 ↗
45. Phase transformation behavior of Ca-doped zirconia sintered at different temperatures10.1007/s43207-021-00183-9 ↗
46. Effect of two-step sintering on the hydrothermal ageing resistance of tetragonal zirconia polycrystals10.1016/j.ceramint.2017.03.052 ↗
47. Effect of nano-TiO2 on properties of 3 mol% yttria-stabilized zirconia ceramic via layered extrusion forming10.1016/j.jeurceramsoc.2020.05.027 ↗
48. High-performance 3D-printed Al2O3 cores for low-temperature sintering10.1016/j.ceramint.2023.09.020 ↗
49. Preparation of Fully Cubic Calcium-Stabilized Zirconia With 10 mol% Calcium Oxide Dopant Concentration by Microwave Processing10.1111/j.1551-2916.2006.01379.x ↗
50. Achieving high overall energy storage performance of KNN-based transparent ceramics by ingenious multiscale designing10.1039/D4TA02425G ↗
51. Synthesis and characterization of low density calcia stabilized zirconia ceramic for high temperature furnace application10.1016/j.matchemphys.2006.01.010 ↗
52. High temperature dielectric properties of calcium zirconate10.1111/ijac.14432 ↗
53. Fabrication of high-strength and anti-hydration water-soluble calcia-based ceramic core modified with nano-ZrO2 via direct ink writing method10.1016/j.ceramint.2023.09.195 ↗
54. Critical evaluation and thermodynamic optimization of the CaO-ZrO2 and SiO2-ZrO2 systems10.1016/j.jeurceramsoc.2016.10.008 ↗
55. Influence of in situ phase formation on properties of calcium zirconate refractories10.1016/j.jeurceramsoc.2016.08.017 ↗
56. Effect of sintering temperature on the aging resistance and mechanical properties of monolithic zirconia10.1016/j.jmrt.2018.07.017 ↗
57. Influence of sintering temperature on the thermal conductivity of digital light processing 3D-printed yttria-stabilized zirconia ceramic10.1016/j.ceramint.2023.06.027 ↗
58. 3D printing of hollow lattice structures of ZrO2 (3Y)/Al2O3 ceramics by vat photopolymerization: Process optimization, microstructure evolution and mechanical properties10.1016/j.jmapro.2022.09.047 ↗
59. Characterization of 3D printed yttria-stabilized zirconia parts for use in prostheses10.3390/nano11112942 ↗