Research on the microstructure and properties of SiCp-SiO2/6061Al composites based on ball milling time
Source abstract
Abstract
In this study, SiCp-SiO 2/6061Al composites were synthesized by integrating SiC and SiO 2 particulates into a 6061Al matrix, followed by ball milling and hot isostatic pressing sintering. The impact of ball milling duration on microstructure, mechanical properties, corrosion resistance, and thermal properties was evaluated. After 10 h of ball milling, reinforcement particles were uniformly dispersed, achieving a material density of over 98 %. Extending milling to 15 h enhanced tensile strength to 253.53 MPa and flexural strength to 433.56 MPa, with a maximum elongation at break of 6.4 %. Uniform SiO 2 distribution improved corrosion resistance, evidenced by a self-corrosion potential of −1209 mV and a self-corrosion current density of 53.02 µA·cm −2. After 20 h, the lowest thermal expansion coefficient, 19.87×10 −6·K −1, was achieved. However, agglomerated particles after 5 h resulted in inferior thermal properties, including a thermal expansion coefficient of 20.45×10 −6·K −1 and thermal conductivity of 94 W·m −1·K −1. The optimal ball milling duration for these composites was determined to be 10 h, balancing performance and cost-effectiveness.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. Characterization and experimental analysis of boron carbide and ricehusk ash reinforced AA7075 aluminium alloy hybrid composite10.1016/j.jallcom.2018.01.185 ↗
2. Corrosion behaviour of SiC and Al2O3 reinforced Al 7075 hybrid aluminium matrix composites by weight loss and electrochemical methods
3. Enhanced mechanical and wear properties of aluminium-based composites reinforced with a unique blend of granite particles and boron carbide for sustainable material recycling
4. High volume fraction of copper coated graphite flake\Nitrogen doped carbon fiber reinforced Aluminum matrix composites10.1016/j.jallcom.2019.153584 ↗
5. Mechanical properties and characterization of zirconium oxide (ZrO2) and coconutshell ash(CSA) reinforced aluminium (Al 6082) matrix hybrid composite10.1016/j.jallcom.2018.06.177 ↗
6. Variation of microstructure and mechanical properties of hybrid particulates reinforced Al-alloy matrix composites with ultrasonic treatment10.1016/j.jallcom.2019.03.074 ↗
7. Microstructure and mechanical behaviors of 6061 Al matrix hybrid composites reinforced with SiC and stainless steel particles10.1016/j.msea.2021.140732 ↗
8. Development and characterization of Al5083-CNTs/SiC composites via friction stir processing10.1016/j.jallcom.2019.05.232 ↗
9. Enhanced mechanical properties and thermo-phySiCal properties of 7075Al hybrid composites reinforced by the mixture of Cr particles and SiCp10.1016/j.jallcom.2017.11.227 ↗
10. Effect of mechanical alloying time and rotation speed on evolution of CNTs/Al-2024 composite powders10.1016/S1003-6326(14)63360-4 ↗
11. Improving carbon nanotube dispersion in aluminum matrix composite powders by a repeating-deformation ball milling process10.1016/j.matchar.2023.112986 ↗
12. Preparation and characterization of nanodiamond-reinforced 6061 aluminum matrix composites via a slurry process and high-energy ball milling10.1016/j.diamond.2023.109829 ↗
13. Unraveling the dispersion mechanism of carbon nanotubes in aluminum powder particles during high energy ball milling by FIB-TEM study10.1016/j.powtec.2023.118339 ↗
14. Effect of Al2O3 content and milling time on microstructure and mechanical properties of aluminum metal matrix composites10.1111/j.1747-1567.2011.00790.x ↗
15. Effect of fly ash and ball milling time on CNT-FA reinforced aluminium matrix hybrid composites10.1088/2053-1591/ab1e20 ↗
16. Effect of high energy ball milling on the morphology, microstructure and properties of nano-sized TiC particle-reinforced 6005A aluminium alloy matrix composite10.1016/j.powtec.2017.07.089 ↗
17. The effect of milling time on the preparation of an aluminum matrix composite reinforced with magnetic nanoparticles10.1016/j.heliyon.2023.e16887 ↗
18. The effect of milling time, and sintering temperature and time on the microstructure-property relationship of aluminium-matrix hybrid composites
19. Effect of ball milling time on the structural characteristics and mechanical properties of nano-sized Y2O3 particle reinforced aluminum matrix composites produced by powder metallurgy route10.1016/j.apt.2021.08.031 ↗
20. Effect of milling time on microstructural and mechanical properties of nano-Al2O3P/6061Al composites prepared by transient liquid-phase sintering10.1016/j.jallcom.2022.167702 ↗
21. Optimizing ball milling parameters for controlling the internal microstructure and tensile characteristics of a laminated carbon nanotube/aluminum-copper-magnesium composite10.1016/j.jallcom.2024.173927 ↗
22. Study on mechanical properties and microstructure of SiO2/Al-7Si-0.3Mg aluminum matrix composites
23. Effect of hot isostatic pressing on the microstructure and properties of magnesium silicide–silicon carbide/aluminum alloy (AlSi7Cu2Mg) composites10.1007/s42114-022-00461-y ↗
24. Effect of hot isostatic pressing on the mechanical properties of aluminium metal matrix nanocomposites produced by dual speed ball milling10.1016/j.jmrt.2019.11.043 ↗
25. Interface structure and properties of spray-forming (SiCp+β-LiAlSiO4)/6092Al matrix composites10.1016/S1003-6326(23)66163-1 ↗
26. Effect of SiC nanoparticle on microstructure and mechanical properties of graphene nanosheet (GNS) reinforced aluminum composites10.1016/j.jallcom.2023.172177 ↗
27. Fabrication and characteristic of Al-based hybrid nanocomposite reinforced with WO3 and SiC by accumulative roll bonding process10.1016/j.jallcom.2015.08.267 ↗
28. Production of aluminum alloy-based metal matrix composites using scrap aluminum alloy and waste materials: influence on microstructure and mechanical properties10.1016/j.jallcom.2019.01.115 ↗
29. Research progress on fabrication technology and properties of SiC particle-reinforced aluminum matrix composites
30. The influence of particle surface oxidation treatment on microstructure and mechanical behavior of 3D-SiCp/A356 interpenetrating composites fabricated by pressure infiltration technique10.1016/j.jmrt.2023.05.118 ↗
31. Overcoming brittleness of high volume fraction Al/SiCp composites by controlling interface characteristics10.1016/j.matdes.2022.111038 ↗
32. Methodology to design the interfaces in SiC/Al composites10.1007/s11661-001-0241-4 ↗
33. Effect of re-sintering temperature on compact microstructure and compressive properties of SiC and Ti reinforced aluminum matrix composites by powder metallurgy10.1080/00084433.2022.2114128 ↗
34. Rice husk ash as pore former and reinforcement on the porosity, microstructure, and tensile strength of aluminum MMC fabricated via the powder metallurgy method10.3390/cryst12081100 ↗
35. Synergistic effect of graphene/boron nitride binary nanoparticles on aluminum hybrid composite properties10.1007/s42114-021-00209-0 ↗
36. Fabrication and characterization of silicon carbide and fly ash reinforced aluminium metal matrix hybrid composites
37. Investigation of mechanical properties in Al359 hybrid metal matrix composite reinforced with SiC and fly ash
38. Evaluation of corrosion property of aluminium-zirconium dioxide (A1ZrO2)nanocomposites
39. Microstructure and corrosion characteristics of in situ aluminum diboride metal matrix composites
40. Effect of the reinforced boron carbide particulate content of AA6061 alloy on formation of the passive film in seawater10.1016/j.corsci.2011.04.023 ↗
41. Effects of dispersed microvoids on thermal expansion behavior of composite materials10.1016/S0921-5093(00)00721-8 ↗
42. Effect of clustering on the mechanical properties of SiC particulate reinforced aluminum alloy 2024 metal matrix composites10.1016/S0921-5093(02)00593-2 ↗
43. Effect of 6061Al matrix particle size on microstructure and properties of SiCp/6061Al matrix composites
44. Numerical homogenization and experimental study of the influence of Graphite content and voids on the coefficients of thermal expansion of 2017 Aluminium matrix composites
45. Fabrication of diamond particles reinforced Al-matrix composites by hot-press sintering10.1016/j.ijrmhm.2013.02.007 ↗