Effect of forging routes on the microstructure and mechanical properties of newly-developed Ti-44Al-5.5Nb-0.5W-0.5Cr-0.3Si-0.1C alloys
Source abstract
Abstract
In this study, the effects of forging routes on the microstructure and tensile properties of Ti-44Al-5.5 Nb-0.5 W-0.5Cr-0.3Si-0.1 C (at%) alloys was comparatively investigated. Results showed that the bare ingot forged at 1400 ℃ (BH) exhibited refined lamellar colonies with narrow lamellar spacing. In contrast, dynamic recrystallized γ grains and lamellar structure with thick lamellar spacing formed in the canned sample deformed at 1320 ℃ (CA). In addition, the heat-treated BH-HT sample showed fully recrystallized texture, while the lamellar structure in the CA-HT presented a preferred orientation, i.e., lamellar interfaces were parallel to rolling direction (RD). The mechanical properties of the CA-HT sample test results showed superior room-temperature ductility of 1.68 % and tensile strength of 515 MPa at 950 ℃ due to the lamellar orientation alignment to tensile direction. According to the temperature drop calculation results, both BH and CA forging routes exhibited rapid cooling rates. The initial microstructure at the pre-heating temperature was maintained until a hot deformation sequence was initiated. Therefore, the BH route could be performed in the α+β region, while the CA route could be carried out in the α-forging condition with the 110 1 ̅ 12 γ texture.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · MXene and MAX Phase Materials · Titanium Alloys Microstructure and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (60)
Show source-provided references
1. Annealing studies of γ-titanium aluminides alloyed with light elements for creep strengthening10.1016/S0966-9795(98)00030-2 ↗
2. Design, processing, microstructure, properties, and applications of advanced intermetallic TiAl alloys10.1002/adem.201200231 ↗
3. Creep behavior and deformation feature of TiAl–Nb alloy with various states at high temperature10.1016/j.msea.2015.10.096 ↗
4. Advances in gammalloy materials–processes–application technology: successes, dilemmas, and future10.1007/s11837-018-2747-x ↗
5. Creep of lamellar TiAl alloys: degradation, stabilization and design of lamellar boundaries10.1016/j.msea.2004.01.124 ↗
6. The role of microstructural stability on compression creep of fully lamellar γ-TiAl alloys10.1016/j.intermet.2004.12.020 ↗
7. Metastable phase and microstructural degradation of a TiAl alloy produced via selective electron beam melting10.1016/j.vacuum.2021.110491 ↗
8. Achieving fine fully lamellar microstructure of casting TiAl alloy by simple heat treatment10.1016/j.matchar.2023.112881 ↗
9. Mechanical properties of Si- and C-doped directionally solidified TiAl–Nb alloys10.1016/j.intermet.2004.01.004 ↗
10. A high tensile strength above 900 ℃ in β-solidified TiAl alloy through alloy design and microstructure optimization10.1016/j.jallcom.2023.169676 ↗
11. Microstructural evolution and mechanical properties of a forged gamma titanium aluminide alloy10.1016/0956-7151(92)90411-7 ↗
12. Effects of microstructure on the deformation and fracture of γ-TiAl alloys10.1016/0921-5093(94)03271-8 ↗
13. Analysis of grain growth in a two-phase gamma titanium aluminide alloy10.1007/s11661-997-0225-0 ↗
14. Fabrication of TiAl components by means of hot forging and machining10.1016/j.intermet.2004.12.012 ↗
15. Design of novel β-solidifying tial alloys with adjustable β/B2-phase fraction and excellent hot-workability10.1002/adem.200800164 ↗
16. Enhancement of creep properties and microstructural stability of intermetallic β-solidifying γ-TiAl based alloys10.1016/j.intermet.2015.03.017 ↗
17. Multi-step heat treatment design for nano-scale lamellar structures of a cast Ti-45Al-8.5Nb-(W, B, Y) alloy10.1016/j.intermet.2016.09.006 ↗
18. Hot deformation of high-Nb-containing γ-TiAl alloy in the temperature range of 1000–1200 °C: microstructural attributes to hot workability10.1007/s42452-019-0380-0 ↗
19. In-situ study of the time–temperature-transformation behaviour of a multi-phase intermetallic β-stabilised TiAl alloy10.1016/j.intermet.2014.09.011 ↗
20. Effect of hot rolling and primary annealing on the microstructure and texture of a β-stabilised γ-TiAl based alloy10.1016/j.actamat.2016.12.056 ↗
21. Microstructure evolution and mechanical properties of a novel beta γ-TiAl alloy10.1016/j.intermet.2012.07.012 ↗
22. Evolution of grain boundary and texture in as-forged Ti–45Al–9Nb–Y alloy during tensile test at different temperature10.1016/j.intermet.2012.01.011 ↗
23. Effect of pack rolling on microstructures and tensile properties of as-forged Ti-44Al-6V–3Nb-0.3Y alloy10.1016/j.intermet.2011.10.003 ↗
24. Microstructure and mechanical properties of large size Ti-43Al-9V-0.2Y alloy pancake produced by pack-forging10.1016/j.intermet.2012.11.004 ↗
25. Mechanism of hydrogen-restrained crack propagation and practical application research of thermohydrogen treatment in a TiAl-based alloy10.1016/j.ijhydene.2019.01.177 ↗
26. Microstructure evolution and recrystallization of Ti-44.5Al-3.8Nb-1Mo-0.2B alloy with different initial microstructure during hot pack rolling10.1016/j.matdes.2022.111138 ↗
27. Achievement of forging without canning for β-solidifying γ-TiAl alloy containing high content of niobium10.1080/10426914.2021.1942902 ↗
28. Temperature transients during hot pack rolling of high temperature alloys10.1016/0956-716X(91)90316-S ↗
29. Experimental Investigation of Emissivity of Steel10.1007/s10765-013-1421-3 ↗
30. As-cast microstructure characteristics dependent on solidification mode in TiAl-Nb alloys10.1016/j.jallcom.2019.151862 ↗
31. Microsegregation in high Nb containing TiAl alloy ingots beyond laboratory scale10.1016/j.intermet.2006.10.003 ↗
32. Crystallographic orientation relationship between α-and γ-Fe
33. Microstructure refinement of Ti-40Al-8Nb alloys via the decomposition of the metastable B2 phase at 1000 °C10.1016/j.jallcom.2020.155575 ↗
34. Insights into the abnormal flow softening of lamellar γ-TiAl alloys during hot-working: experimental analysis and numerical simulation10.1016/j.msea.2022.143695 ↗
35. High strength in high Nb containing TiAl alloy sheet with fine duplex microstructure produced by hot pack rolling10.1016/j.jallcom.2016.12.005 ↗
36. Microstructure refinement assisted by α-recrystallization in a peritectic TiAl alloy10.1016/j.jmrt.2021.01.073 ↗
37. A review of dynamic recrystallization phenomena in metallic materials10.1016/j.matdes.2016.09.012 ↗
38. Hot deformation and dynamic recrystallization behavior of TiAl-based alloy10.1016/j.intermet.2019.106521 ↗
39. Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions10.1016/j.pmatsci.2013.09.002 ↗
40. An innovation for microstructural modification and mechanical improvement of TiAl alloy via electric current application10.1038/s41598-019-41881-z ↗
41. Crystallography and phase transformation mechanisms in TiAl-based alloys – a synthesis10.1016/j.intermet.2009.05.013 ↗
42. Lamellar transformation in near-γ TiAl alloys—Quantitative analysis of kinetics and microstructure10.1016/j.msea.2008.02.009 ↗
43. The relationships of microstructure and properties of a fully lamellar TiAl alloy10.1016/S0966-9795(99)00128-4 ↗
44. Development of ultrafine lamellar structures in two-phase γ-TiAl alloys10.1007/s11661-998-0163-5 ↗
45. Texture evolution during α-forging of γ-TiAl alloys10.1016/S0921-5093(97)00659-X ↗
46. Blackburn · 1970 · 633
47. Effect of carbon addition and cooling rate on lamellar structure of peritectic TiAl-based alloy10.1016/j.intermet.2020.107007 ↗
48. Dynamic recrystallization behavior of an as-cast TiAl alloy during hot compression10.1016/j.matchar.2014.09.013 ↗
49. Continuous cooling transformation (CCT) behavior of a high Nb-containing TiAl alloy10.1016/j.mtla.2018.11.018 ↗
50. In-situ study on γ phase transformation behaviour of γ-TiAl alloys at different cooling rates10.1016/j.pnsc.2022.03.004 ↗
51. Polysynthetic twinned TiAl single crystals for high-temperature applications10.1038/nmat4677 ↗
52. Room-temperature tensile deformation of polysynthetically twinned (PST) crystals of TiAl10.1016/0956-7151(92)90472-Q ↗
53. Phenomenological observations of lamellar orientation effects on the creep behavior of Ti–48at%Al PST crystals10.1016/S1359-6454(99)00347-X ↗
54. Effects of Al-concentration and lamellar spacing on the room-temperature strength and ductility of PST crystals of TiAl10.1016/S0921-5093(97)00601-1 ↗
55. Deformation characteristics of polysynthetically twinned (PST) crystals during creep at 1150 K10.1016/S0966-9795(99)00081-3 ↗
56. Strength and ductility in TiAl alloys10.1016/S0966-9795(98)00037-5 ↗
57. Effects of microstructure and C and Si additions on elevated temperature creep and fatigue of gamma TiAl alloys10.1016/j.intermet.2014.04.006 ↗
58. The role of grain size and selected microstructural parameters in strengthening fully lamellar TiAl alloys10.1007/s11661-998-0157-3 ↗
59. Microstructural control and mechanical properties of dual-phase TiAl alloys10.1016/S0966-9795(98)00062-4 ↗
60. Effects of Nb and Al on the microstructures and mechanical properties of high Nb containing TiAl base alloys10.1016/S0966-9795(02)00037-7 ↗