journal article·2024-04

Revealing the effect of oriented microstructures on the anisotropy of fatigue crack propagation behavior in TiB2/Al-Cu-Mg-Mn composite

Qingqing Pu, Jiwei Geng, Tai Luo, Yugang Li, Yi Shi, Xianfeng Li, Dong Chen, Hongze Wang, Haowei Wang

Publisher page

Abstract

The particle-reinforced metal matrix composite extruded plate exhibits oriented microstructures including elongated grains and aligned distribution of phases/particles, directly influencing the anisotropy in fatigue crack propagation (FCP). It is found that the crack advances perpendicularly to oriented microstructures when the load is parallel to the long axis of elongated grains (E-T sample), exhibiting the lowest FCP rate. When the sample is loaded along the short axis of elongated grains (T-E sample), the crack is parallel to the oriented microstructures, exhibiting the highest FCP rate. The influence of particles on crack propagation is dependent on the width of particle band. Narrow particle bands promote crack deflection and retard FCP. Wide particle bands weaken the hindering effect as numerous particles shorten dislocation slip distance. The rod-shaped T-Al 20Cu 2Mn 3 dispersoids can carry larger load transfer than other two loading directions when the sample is loaded along extrusion direction. Overall, the geometric shielding from oriented microstructures is an important factor in the anisotropy of FCP. The particle-induced geometric shielding contribution is decreased in the case of loading perpendicular to particle bands, resulting in the enhancement of the FCP anisotropy behavior.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Microstructure and mechanical properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (70)

Show source-provided references
1. Influence of nanoparticles addition on the fatigue failure behavior of metal matrix composites: Comprehensive review10.1016/j.engfailanal.2023.107751 ↗
2. Nanoparticle enabled high performance high modulus steels10.1016/j.scriptamat.2021.113954 ↗
3. Enhancing strength and ductility of Al-matrix composite via a dual-heterostructure strategy10.1016/j.ijplas.2023.103825 ↗
4. Towards the work hardening and strain delocalization achieved via in-situintragranular reinforcement in Al-CuO composite10.1016/j.actamat.2023.119110 ↗
5. Achieving high strength and ductility in ODS-W alloy by employing oxide@W core-shell nanopowder as precursor10.1038/s41467-021-25283-2 ↗
6. Processing and properties of magnesium containing a dense uniform dispersion of nanoparticles10.1038/nature16445 ↗
7. Recent progress in aluminum metal matrix composites: A review on processing, mechanical and wear properties10.1016/j.jmapro.2020.09.010 ↗
8. Influence of TiB2 addition on friction and wear behaviour of Al2024-TiB2 ex-situ composites10.1016/S1003-6326(21)65575-9 ↗
9. A review of recent developments in the corrosion performance of aluminium matrix composites10.1016/j.jallcom.2023.169508 ↗
10. Corrosion behavior of nano-treated AA7075 alloy with TiC and TiB2 nanoparticles10.1016/j.corsci.2022.110479 ↗
11. Study fatigue crack initiation in TiB2/Al-Cu-Mg composite by in-situ SEM and X-ray microtomography10.1016/j.ijfatigue.2020.105976 ↗
12. High cycle fatigue behavior of in-situ ZrB2/AA6111 composites10.1016/j.msea.2020.139590 ↗
13. Interfacial strain evolution and abnormal Poisson's ratios in Al nuclei for the Al/TiB2 heterostructure10.1016/j.scriptamat.2023.115508 ↗
14. Atomic-scale investigation of the interface precipitation in a TiB2 nanoparticles reinforced Al-Zn-Mg-Cu matrix composite10.1016/j.actamat.2019.11.068 ↗
15. Cyclic deformation and dynamically induced short-range ordering in small particles reinforced Al composite10.1016/j.ijplas.2023.103568 ↗
16. Effects of heat treatment on the microstructure, texture and mechanical property anisotropy of extruded 2196 Al-Cu-Li alloy10.1016/j.jallcom.2020.158102 ↗
17. Improving mechanical anisotropy and corrosion resistance of extruded AA7075 alloy by warm cross rolling and annealing10.1016/j.jallcom.2021.158725 ↗
18. Columnar grain morphology and mechanical anisotropy of face-centered cubic metals and alloys10.1016/j.scriptamat.2023.115684 ↗
19. Effect of grain shape and texture on the yield strength anisotropy of Al-Li alloy sheet10.1016/S1359-6462(98)00481-3 ↗
20. Modelling the combined effect of grain size and grain shape on plastic anisotropy of metals10.1016/j.ijplas.2011.12.002 ↗
21. Anisotropic yielding stress of 2198 Al-Li alloy sheet and mechanisms
22. Training high-strength aluminum alloys to withstand fatigue10.1038/s41467-020-19071-7 ↗
23. Mechanisms of fatigue crack growth - a critical digest of theoretical developments10.1111/ffe.12392 ↗
24. Influence of specimen orientation on fatigue crack growth in 7050-T7451 and 2050-T8 aluminium alloys10.1016/j.ijfatigue.2022.107136 ↗
25. The role of grain boundaries on fatigue crack initiation - An energy approach10.1016/j.ijplas.2010.09.009 ↗
26. Investigation of high-cycle fatigue and fatigue crack propagation characteristic in 5083-O aluminum alloy10.1016/j.ijfatigue.2019.05.020 ↗
27. Effects of secondary particle-induced recrystallization on fatigue crack growth in AA2524/Al-Cu-Mg T3 alloy sheets10.1016/j.jallcom.2016.05.317 ↗
28. Fatigue crack growth anisotropy in ultrafine-grained iron10.1016/j.actamat.2016.12.059 ↗
29. Nanoparticle promoted solution treatment by reducing segregation in AA703410.1016/j.msea.2021.141691 ↗
30. Study on nano-treating of Al-Mg-Si-Cu alloys with TiC
31. Fatigue crack growth in SiC particle reinforced Al alloy matrix composites at high and low R-ratios by in situ X-ray synchrotron tomography10.1016/j.ijfatigue.2014.05.010 ↗
32. Revealing the fatigue crack initiation mechanism of a TiB2-reinforced steel matrix composite10.1016/j.ijfatigue.2019.105276 ↗
33. Effect of particle morphology on fatigue crack propagation mechanism of TiB2-reinforced steel matrix composites10.1016/j.engfracmech.2022.108752 ↗
34. Crack closure and plastic zone sizes in fatigue10.1111/j.1460-2695.1991.tb00674.x ↗
35. Fatigue crack growth behavior in powder-metallurgy 6061 aluminum alloy reinforced with submicron Al2O3 particulates10.1016/j.compositesb.2012.05.031 ↗
36. Influence of SiC particle distribution and prestraining on fatigue crack growth rates in aluminium AA 6061-SiC composite material10.1179/mst.1991.7.7.596 ↗
37. Fatigue crack growth and fracture of 30 wt% B4C/6061Al composites10.1111/ffe.12579 ↗
38. The solution treatment of in-situ sub-micron TiB2/2024 Al composite10.1016/j.matdes.2016.03.024 ↗
39. ASTM E647, Standard test method for measurement of fatigue crack growth rates, 2015.
40. Recrystallization in fibrous and particulate metal matrix composites10.1016/0921-5093(91)90576-9 ↗
41. A review on the fatigue cracking of twin boundaries: Crystallographic orientation and stacking fault energy10.1016/j.pmatsci.2022.101011 ↗
42. Crossing grain boundaries in metals by slip bands, cleavage and fatigue cracks10.1098/rsta.2014.0131 ↗
43. The effect of Mn containing dispersoids on the distribution of slip and fracture mode in Al-Mg-Si-Mn alloys
44. Nano-treating promoted solute dissolution for novel high strength Al-Cu-Mg alloys10.1016/j.mtla.2022.101466 ↗
45. The enhanced superplasticity of a 2024 matrix nanocomposite reinforced by TiC particles10.1016/j.msea.2020.138926 ↗
46. Crystallographic relationships of T-/S-phase aggregates in an Al-Cu-Mg-Ag alloy10.1016/j.actamat.2018.12.036 ↗
47. Morphologies, orientation relationships, and evolution of the T-phase in an Al-Cu-Mg-Mn alloy during homogenisation10.1016/j.jallcom.2017.03.161 ↗
48. Quantitative characterization of short fatigue crack and grain boundary interaction behavior in zirconium10.1016/j.ijfatigue.2022.106894 ↗
49. Investigation of fatigue crack propagation behavior of 5083 aluminum alloy under various stress ratios: Role of grain boundary and Schmid factor10.1016/j.msea.2019.138871 ↗
50. Investigation on fatigue crack propagation behaviors in the thickness direction of 2519A aluminum alloy thick plate10.1016/j.ijfatigue.2022.107099 ↗
51. Influence of microstructure on fatigue crack propagation behaviors of Al-xCu-1.5Li-X alloys10.1016/j.ijfatigue.2022.107363 ↗
52. A new fatigue crack growth mechanism of high-strength steels10.1016/j.msea.2022.142969 ↗
53. New insights into the anisotropic ductility of additively manufactured Inconel 71810.1016/j.ijplas.2023.103738 ↗
54. The effects of α/β phase interfaces on fatigue crack deflections in additively manufactured titanium alloy: A peridynamic study10.1016/j.ijfatigue.2020.105622 ↗
55. Influence of grain shape and orientation on the mechanical properties of high pressure torsion deformed nickel10.1016/j.msea.2012.09.061 ↗
56. Fatigue crack growth behavior of Al-Mg-Sc alloy10.1016/j.msea.2014.01.045 ↗
57. On the reversibility of dislocation slip during cyclic deformation of Al alloys containing shear-resistant particles10.1016/j.actamat.2011.03.007 ↗
58. Investigation of particle fracture during fatigue of aluminum 202410.1016/j.ijfatigue.2018.02.001 ↗
59. Anisotropy in fatigue crack propagation behavior of Al-Cu-Li alloy thick plate10.1016/j.matchar.2017.07.025 ↗
60. Insight into the formation mechanism and interaction of matrix/TiB whisker textures and their synergistic effect on property anisotropy in titanium matrix composites10.1016/j.jmst.2021.08.033 ↗
61. Generalized shear-lag model for load transfer in SiC/Al metal-matrix composite10.1557/JMR.2003.0398 ↗
62. The effect of anisotropic microstructure on the crack growth and fatigue overload behaviour of ultrafine-grained nickel10.1016/j.actamat.2019.11.024 ↗
63. Microstructural effects on short fatigue crack propagation in cast Al-Si alloys10.1016/j.ijfatigue.2023.107788 ↗
64. Analytical and finite element modelling of roughness induced crack closure10.1016/j.actamat.2003.09.019 ↗
65. The relationship between surface roughness and fatigue crack growth ratein AA7050-T7451 subjected to periodic underloads10.1016/j.ijfatigue.2022.107355 ↗
66. Direct observation of three-dimensional short fatigue crack closure behavior in Ti-6Al-4V alloy using ultra-high-resolution X-ray microtomography10.1016/j.ijfatigue.2022.107428 ↗
67. A macrostructural model for simulating the combined effects of roughness and plasticity induced fatigue crack closure10.1016/j.ijfatigue.2012.06.017 ↗
68. Fatigue crack deflection and fracture surface contact: micromechanical models10.1007/BF02816051 ↗
69. Effect of grain size on fatigue-crack growth in 2524 aluminium alloy10.1016/j.ijfatigue.2015.11.011 ↗
70. Revisiting fatigue crack growth in various grain size regimes of Ni10.1016/j.msea.2015.08.071 ↗