Upgrading recycling of Al–7 wt%Si alloys using electromagnetic force in directional solidification
Source abstract
Abstract
The highly reactive chemical nature of aluminum makes it production energy-intensive or essentially impossible to extract alloying elements from Al-based liquids. Using molten salt fluxing and electrolysis processes can effectively refine coarse Al scraps. However, the generation of toxic gases and hazardous dross during these processes can cause significant environmental protection challenges and result in notable social concerns. Therefore, the primary recycling of post-consumer Al in industries currently proceeds mainly in a cascade manner, which is not sustainable when considering the Al cycle trends in the coming decades. Herein, we develop a novel process to separate primary Al from the crystallizing liquid when a constant electromagnetic force (EMF) is applied. Using this technique, we successfully upgraded Al–7mass%Si (hereafter, unless specified otherwise) alloy to approximately Al–3.6%Si in directional solidification . The separation mechanism was discussed in terms of the electrical properties of the respective phases during solidification. Fluid flow simulation results were applied to elucidate the separation behavior in the alloy. The upper and lower limits to separate the crystallizing alloy into an Al-rich and Si-rich areas were determined when the controlling factors were clarified, which made it possible to scale up the present laboratory-based setup to an industrial level. Moreover, the energy consumption of the process was slightly higher than that required for remelting only. Using the EMF technique to separate the crystallizing alloy into Al-rich and Si-rich regions did not produce hazardous dross or toxic gases. This energy-saving and eco-friendly process can provide a breakthrough to overcome the “dead metal” crisis and thus realize sustainability by upgrading recycling of post-consumer hypoeutectic Al–Si casting alloys.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Bauxite Residue and Utilization · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. International Aluminium Institute. 〈https://international-aluminium.org/〉 (accessed on 16 May 2023).
2. Alloy development and process innovations for light metals casting10.1016/j.jmatprotec.2022.117606 ↗
3. E. Musk, Tesla annual shareholder meeting presentation. Sep 22, 2020, Fremont, CA, USA.
4. Automotive News Europe, Giga presses---the giant die casts that are reshaping car manufacturing, 10 Feb 2023.
5. Mapping the global flow of aluminum: From liquid aluminum to end-use goods10.1021/es304256s ↗
6. U.S. Energy Requirements for Aluminum Production; Historical Perspective, Theoretical Limits and Current Practices, U.S. Department of Energy, February 2007, p. 64.
7. International Aluminium Institute, Life cycle inventory data and environmental metrics for the primary aluminium industry , 2019 data, final report, p. 40.
8. Materials recycling: the virtue of necessity10.1016/0361-3658(86)90137-2 ↗
9. Report of inventory survey of scrap melting, 〈https://www.aluminum.or.jp/environment/pdf/2–1.pdf〉. (Japan Aluminum Association, 2007).
10. Improving aluminum recycling: a survey of sorting and impurity removal technologies10.1016/j.resconrec.2011.10.010 ↗
11. Thermodynamic analysis of contamination by alloying elements in aluminium recycling10.1021/es9038769 ↗
12. Thermodynamic criteria for the removal of impurities from end-of-life magnesium alloys by evaporation and flux treatment10.1088/1468-6996/12/3/035003 ↗
13. Design for recycling: evaluation and efficient alloy modification10.1111/j.1530-9290.2010.00229.x ↗
14. Challenges in metal recycling10.1126/science.1217501 ↗
15. The role of automobiles for the future of aluminum recycling10.1021/es300648w ↗
16. Role and potential of aluminium and its alloys for a zero-carbon society10.2320/matertrans.MT-LA2022009 ↗
17. Evolution of aluminum recycling initiated by the introduction of next-generation vehicles and scrap sorting technology10.1016/j.resconrec.2012.06.006 ↗
18. Al–Si alloys10.2464/jilm.38.426 ↗
19. The properties and uses of fluxes in molten aluminum processing10.1007/s11837-998-0285-7 ↗
20. The production of high-purity aluminium in Japan10.1007/BF03220434 ↗
21. A solid-state electrolysis process for upcycling aluminium scrap10.1038/s41586-022-04748-4 ↗
22. Applications of molten salt and progress of molten salt electrolysis in secondary metal resource recovery10.1007/s12613-020-2175-0 ↗
23. On trending technologies of aluminum dross recycling: a review10.1016/j.psep.2023.01.010 ↗
24. Strategies for improving the sustainability of structural metals10.1038/s41586-019-1702-5 ↗
25. Making sustainable aluminum by recycling scrap: the science of “dirty” alloys10.1016/j.pmatsci.2022.100947 ↗
26. Alternative fractional crystallization-based methods to produce high-purity aluminum10.1016/j.jmrt.2021.03.025 ↗
27. Refining by fractional solidification10.1007/BF02653975 ↗
28. Electromagnetic separation of coarse Al–Si melts: the migration behavior of iron-rich phase and continuous growth of primary silicon10.1016/j.jallcom.2019.153006 ↗
29. Separation mechanism of primary silicon from hypereutectic Al–Si melts under alternating electromagnetic fields10.1007/s11661-015-2889-1 ↗
30. Simultaneous removal of silicon and iron-rich phases from coarse Al–Si alloys using manganese under electromagnetic field10.1007/s11663-018-1412-7 ↗
31. Effects of silicon content on the separation and purification of primary silicon from hypereutectic aluminum–silicon alloy by alternating electromagnetic directional solidification10.1016/j.seppur.2018.10.033 ↗
32. Continuous solidification of Si from Si–Al melt under the induction heating10.2355/isijinternational.47.582 ↗
33. Separation mechanism of the primary Si phase from the hypereutectic Al–Si alloy using a rotating magnetic field during solidification10.1016/j.actamat.2014.03.031 ↗
34. Separation and purification of Si from solidification of hypereutectic Al–Si melt under rotating magnetic field10.1016/j.jcrysgro.2014.04.003 ↗
35. Macro segregation formation mechanism of the primary silicon phase in directionally solidified Al–Si hypereutectic alloys under the impact of electric currents10.1016/j.actamat.2015.07.002 ↗
36. Impurity phases and their removal in Si purification with Al–Si alloy using transition metals as additives10.1016/j.jallcom.2017.10.292 ↗
37. 〈https://aluminium-guide.com/en/innovacii-kompanii-tesla-v-alyuminij/〉 (accessed on 16 May 2023).
38. S. Jason, P. Grant, H. Quinlin, P. Avinash, P. Sivanesh, L. Omar, Die casting aluminum alloys for structural components, Patent WO 2021/150604.
39. Impurity behavior in aluminum extraction by low-temperature molten salt electrolysis10.1149/1945-7111/ab98ad ↗
40. Kurz · 2023 · 342
41. Thermophysical properties of liquid aluminum10.1007/s11661-017-4053-6 ↗
42. Thermal and electrical conductivity of liquid Al–Si alloys10.1007/s10765-019-2497-1 ↗
43. Controlling microstructures of AZ31 magnesium alloys by an electromagnetic vibration technique during solidification: From experimental observation to theoretical understanding10.1016/j.actamat.2007.04.035 ↗
44. Prediction of dendritic growth and microsegregation patterns in a binary alloy using the phase-field method10.1016/0956-7151(94)00285-P ↗
45. Density and thermal expansion of liquid Al–Si alloys10.1007/s10853-011-6219-8 ↗