Preparation of CoCrFeMnNi-based high-entropy/aluminide laminated composites: Multielement interdiffusion reactions
Source abstract
Abstract
CoCrFeMnNi-based high-entropy/aluminide laminate (HAL) composites were produced following the hot pressing diffusion sintering method. The microstructure of the samples was analyzed using the SEM, EDS, and EBSD techniques, and the results revealed that the diffusion reaction phases of the HAL composite consisted of a four-layer aluminide structure based on the Al 13(Cr, Mn, Fe, Co, Ni) 4 phase. The diffusion behavior of iron dominated the resulting phase, leading to the formation of Fe-Al compounds. Under the influence of the hysteresis diffusion effect of high entropy alloys, Al 13(Cr, Mn, Fe, Co, Ni) 4 phase layers (ASL I–III) with different grain sizes and growth orientations are formed due to the difference of diffusion rates at different interfaces. At the front end of the diffusion reaction, the aggregation layer of the secondary phase Al 9(Fe, Co, Ni) 2 appears due to the segregation of Co and Ni elements. The growth kinetics model of HAL composites was explored, and it was observed that a mixture diffusion type controlled the growth of the aluminide layer via ‘grain boundary and lattice diffusion’. The mechanical properties and failure modes of the HAL composites were investigated through quasi-static and dynamic mechanical tests. The fracture toughness reached 25 MPa·m 1/2 , and the main energy dissipation modes were the deformation of the ductile layer and the fracture of the hard, brittle layer. The dynamic impact failure modes were primarily deformation and 45% adiabatic shear bands, and the impact strength and energy consumption reached up to 1800 MPa and 2260 J/mm 3 . HAL composites with high alumina content exhibited prominent crack propagation and fragmentation properties under high-speed impact. The stress wave was significantly attenuated in the crushed aluminide layer, which significantly improved the energy absorption effect of aluminide.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Entropy Alloys Studies · High-Temperature Coating Behaviors · Intermetallics and Advanced Alloy Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. A short review on mechanical properties of graphene reinforced metal matrix composites10.1016/j.jmrt.2020.01.077 ↗
2. Mechanical response and microstructure revolution of SiC particle-reinforced Al-MMCs under ultrasonic loading
3. Design, fabrication and characterization of FeAl-based metallic-intermetallic laminate (MIL) composites10.1016/j.actamat.2019.06.039 ↗
4. Study on the microstructure and properties of graphene powder-reinforced Ti-Al metal-intermetallic laminated composite
5. Mesoscale hetero-deformation induced (HDI) stress in FeAl-based metallic-intermetallic laminate (MIL) composites10.1016/j.actamat.2021.116949 ↗
6. On the texture and superstructure formation in Ti–TiAl3–Al MIL composites10.1016/j.intermet.2021.107231 ↗
7. Microstructure evolution and mechanical properties of Ti-Ni-Al ternary metallic-intermetallic laminate (MIL) composites10.1016/j.jallcom.2022.167853 ↗
8. Microstructure and mechanical properties of superelastic NiTi fiber reinforced NiTi/(Al3Ti+ Al3Ni) metal-intermetallic laminated (SFR-MIL) composites10.1088/2053-1591/ac0558 ↗
9. The propagation of a solid‐state combustion wave in Ni‐Al foils10.1063/1.343777 ↗
10. Microstructure evolution in metal-intermetallic laminate (MIL) composites synthesized by reactive foil sintering in air10.1007/s11661-001-0237-0 ↗
11. Effect of sintering pressure and temperature on structure and properties of NiAl metal-intermetallic composites produced by SPS10.1016/j.matchar.2021.111415 ↗
12. Ti-Al3Ti metal-intermetallic laminate (MIL) composite with a cubic titanium trialuminide stabilized with silver: Selection of fabrication regimes, structure, and properties10.1016/j.jallcom.2022.165480 ↗
13. Design of shock wave attenuation effects on multi-impedance-matched laminated composites10.1016/j.jmrt.2023.02.143 ↗
14. Design, fabrication and optimization of FeAl–FeAl2 eutectoid metallic-intermetallic laminate (MIL) composites10.1016/j.mtla.2020.100859 ↗
15. Fabrication and microstructure evolution of B2 structure-based metal-intermetallic-laminate composites10.1016/j.jallcom.2021.162073 ↗
16. Influence of hot pressing on the microstructure of multi-layered ti/al composites10.24425/amm.2021.136435 ↗
17. Three-dimensional processing map based on BP-ANN and interface microstructure of Fe/Al laminated sheet10.1016/j.matchemphys.2023.127431 ↗
18. Synthetic multifunctional metallic-intermetallic laminate composites10.1007/s11837-005-0229-4 ↗
19. Microstructure evolution in Fe-based-aluminide metallic–intermetallic laminate (MIL) composites10.1016/j.msea.2015.10.019 ↗
20. Microstructure characteristics of a high-entropy-alloy intermetallic laminate composite10.1016/j.matlet.2020.127937 ↗
21. Microstructure evolution in a martensitic 430 stainless steel–Al metallic–intermetallic laminate (MIL) composite10.1016/j.msea.2015.07.014 ↗
22. Interaction of iron-chromium alloys containing 10 and 25 mass% chromium with liquid aluminium - Part I - Dissolution kinetics10.1023/A:1025129803413 ↗
23. Microstructure studies of an aluminide coating on 9Cr-1Mo steel during high temperature oxidation10.1016/j.surfcoat.2005.11.038 ↗
24. Nature of CoCrFeMnNi/Fe and CoCrFeMnNi/Al Solid/Solid Interface10.1007/s40195-021-01325-y ↗
25. Phase formation and mechanical properties of iron-based intermetallic/steel laminate composites10.1007/s42114-021-00264-7 ↗
26. Interfacial phases formed in friction stir lap welding high entropy alloy to Al alloy10.1016/j.scriptamat.2021.113972 ↗
27. The effect of particle content and sintering time on the properties of Al-Al9Co2-Al13Co4 composites, made by powder metallurgy10.1016/j.matpr.2022.07.220 ↗
28. Evaluation of data obtained with diffusion couples of binary single-phase and multiphase systems10.1016/0001-6160(69)90131-X ↗
29. Thermodynamic analysis of the Fe-Al-C ternary system by incorporating ab initio energetic calculations into the CALPHAD approach10.2355/isijinternational.44.1738 ↗
30. Aluminization of high purity iron and stainless steel by powder liquid coating10.1016/j.actamat.2004.01.009 ↗