journal article·2022-03Open access

Influence of second phase particles on the mechanical properties of a high solute Al-Zn-Mg alloy fabricated through laser powder bed fusion

A.P. Babu, M.C. Lam, J. Ma, A. Huang, N. Birbilis

Abstract

Abstract A high solute 7xxx series aluminium alloy, Al-14Zn-3Mg (in wt. %), was prepared using laser powder bed fusion (LPBF). To provide an insight into the correlation of second phase particles and mechanical properties, several heat treatment conditions were modelled with CALPHAD, and phase transformations were realised through in-situ characterisation techniques. It was revealed that the formation of T-phase (Mg32(Zn, Al)49) at 400°C contributed to loss of ductility from the direct heat treatment of as-LPBF Al-14Zn-3Mg. However, the improvement in hardness of solutionised and peak aged Al-14Zn-3Mg was attributed to the formation of high volume fraction of η’ and η (MgZn2) precipitates with low inter-precipitate spacing.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. Lucio · 1976
2. Polmear · 2010
3. Davies · Corros. Alum. Alum. Alloy. · 199910.31399/asm.tb.caaa.9781627082990 ↗
4. Characterisation of the composition and volume fraction of η′ and η precipitates in an Al-Zn-Mg alloy by a combination of atom probe, small-angle X-ray scattering and transmission electron microscopy10.1016/j.actamat.2005.03.004 ↗
5. Influence of predeformation and ageing of an Al-Zn-Mg Alloy-II. Modeling of precipitation kinetics and yield stress10.1016/S1359-6454(98)00296-1 ↗
6. Solute strengthening from first principles and application to aluminum alloys10.1016/j.actamat.2012.03.037 ↗
7. Physical Metallurgy of Aluminum Alloys, Alum
8. Mesoscopic structure control of spray formed high strength Al-Zn-Mg-Cu alloys10.1016/j.actamat.2005.03.007 ↗
9. Precipitation behavior and mechanical properties of Al–Zn–Mg alloy with high Zn concentration10.1016/j.jallcom.2020.154005 ↗
10. High strength and large ductility in spray-deposited Al-Zn-Mg-Cu alloys10.1016/j.jallcom.2014.02.126 ↗
11. Effects of Mg and Cu on microstructures and properties of spray-deposited Al-Zn-Mg-Cu alloys10.1016/j.jallcom.2017.05.101 ↗
12. Additive manufacturing of metals: a brief review of the characteristic microstructures and properties of steels, Ti-6Al-4V and high-entropy alloys10.1080/14686996.2017.1361305 ↗
13. Selective laser melting of Al-Zn-Mg-Cu: Heat treatment, microstructure and mechanical properties10.1016/j.jallcom.2016.11.210 ↗
14. Selective laser melting of Al7050 powder: Melting mode transition and comparison of the characteristics between the keyhole and conduction mode10.1016/j.matdes.2017.09.014 ↗
15. Microstructures and tensile properties of a selective laser melted Al–Zn–Mg–Cu (Al7075) alloy by Si and Zr microalloying10.1016/j.msea.2020.139492 ↗
16. Selective laser melting additive manufacturing of 7xxx series Al-Zn-Mg-Cu alloy: Cracking elimination by co-incorporation of Si and TiB2
17. Microstructure characterization of SLM-processed Al-Mg-Sc-Zr alloy in the heat treated and HIPed condition
18. Precipitation kinetics, microstructure evolution and mechanical behavior of a developed Al-Mn-Sc alloy fabricated by selective laser melting10.1016/j.actamat.2020.04.015 ↗
19. Microstructure, tensile properties and thermal stability of AlMgSiScZr alloy printed by laser powder bed fusion10.1016/j.jmst.2020.08.033 ↗
20. Towards a high strength aluminium alloy development methodology for selective laser melting10.1016/j.matdes.2019.107775 ↗
21. Selective laser melting of a high strength Al[sbnd]Mn[sbnd]Sc alloy: Alloy design and strengthening mechanisms10.1016/j.actamat.2019.04.014 ↗
22. Rometsch · 2019
23. Laser powder bed fusion of high solute Al-Zn-Mg alloys: Processing, characterisation and properties10.1016/j.matdes.2020.109183 ↗
24. On the heat treatment and mechanical properties of a high solute Al–Zn–Mg alloy processed through laser powder bed fusion process10.1016/j.msea.2021.140857 ↗
25. Single-crystal growth of the complex metallic alloy phase Mg32(Al,Zn)4910.1016/j.intermet.2008.04.012 ↗
26. Microstructure and strength of a novel heat-resistant aluminum alloy strengthened by T-Al6Mg11Zn11 phase at elevated temperatures10.1016/j.msea.2018.10.034 ↗
27. Morphology and mechanical properties of the T-Al6Mg11Zn11 phase in the eutectic microstructure of Al–Zn–Mg ternary alloys10.1016/j.intermet.2020.106881 ↗
28. Friction stir welding of novel T-phase strengthened Zn-modified Al–Mg alloy10.1007/s10853-020-05609-z ↗
29. A high-strength AlZnMg alloy hardened by the T-phase precipitates10.1016/j.jallcom.2014.04.185 ↗
30. Intermetallic phase evolution of 7050 aluminum alloy during homogenization10.1016/j.intermet.2012.03.006 ↗
31. An electron microscope investigation of the microstructure in an aluminium-zinc-magnesium alloy10.1016/0001-6160(70)90016-7 ↗
32. GP-zones in Al-Zn-Mg alloys and their role in artificial aging10.1016/S1359-6454(01)00251-8 ↗
33. L.F. (Lucio F. Mondolfo, Al-Mg-Zn alloys - A review of the literature, Res. Dev. Center, Reverse Copp. Brass Inc.,. (1967).