journal article·2022-02

Effects of different holding pressures on the microstructure and mechanical properties of Al-5.9Zn-2.2Mg-1.8Cu alloy

Xuanjie Yan, Pan Tan, Yudong Sui, Yehua Jiang, Qudong Wang

Publisher page

Abstract

Abstract In this study, a low-pressure casting process was used to examine the influence of the holding pressure on the Al–5.9Zn–2.2Mg–1.8Cu alloy. The study aimed to refine the grain structure and optimize the microstructural homogeneity and mechanical properties of the alloy. The phase composition, microstructure, chemical composition, and fracture morphology of the alloy were determined using optical microscopy, SEM, inductively coupled plasma spectroscopy, and XRD. As the holding pressure increased, the theoretical crystallisation temperature of the alloy increased, which increased the degree of undercooling during solidification and the effective number of nuclei, resulting in grain refinement. In addition, increase in the holding pressure strengthened the feeding ability of the alloy melt and reduced the occurrence of shrinkage porosity defects. When the optimal pressure was exceeded, the nucleation rate as well as the denseness of the alloy decreases. When the holding pressure was 0.035 MPa, the grain refining effect was the best and the microstructure was the most uniform. The yield strength, tensile strength, and elongation of the alloy reached the maximum values of 264.6 MPa, 290.8 MPa, and 7.7%, respectively. When the holding pressure was >0.035 MPa, the structure was not further refined; in contrast, the grains were larger, and the mechanical properties were inferior.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. Damage micromechanisms in high Mn and Zn content 7XXX aluminum alloys10.1016/j.msea.2020.139423 ↗
2. Precipitation strengthening of aluminum alloys by room-temperature cyclic plasticity10.1126/science.aav7086 ↗
3. Study of the constitutive behavior of 7075-T651 aluminum alloy10.1016/j.ijimpeng.2017.05.002 ↗
4. Predicting yield strengths of Al-Zn-Mg-Cu-(Zr) aluminium alloys based on alloy composition or hardness10.1016/j.matdes.2016.03.071 ↗
5. A study of crack initiation mechanism in the aluminum alloy 7475-T7351 when loading10.1016/j.prostr.2020.01.131 ↗
6. Mechanical property and characterization of 7A04-T6 aluminum alloys bonded by friction stir welding10.1016/j.jmapro.2020.02.018 ↗
7. Study of buckling behavior for 7A04-T6 aluminum alloy rectangular hollow columns10.1016/j.tws.2021.108410 ↗
8. Selective laser melting of Al-Zn-Mg-Cu: heat treatment, microstructure and mechanical properties10.1016/j.jallcom.2016.11.210 ↗
9. The influence of natural aging and repeated solution annealing on microstructure and mechanical properties of hot extruded alloys Al 7020 and Al 717510.1016/j.msea.2017.10.048 ↗
10. Age-hardening of high pressure die casting AlMg alloys with Zn and combined Zn and Cu additions10.1016/j.matdes.2019.107927 ↗
11. Microstructures, mechanical properties and solidification mechanism of a hot tearing sensitive aluminum alloy asymmetric part fabricated by squeeze casting10.1016/j.jallcom.2021.161254 ↗
12. Impact behaviour of A356 alloy for low-pressure die casting automotive wheels10.1016/j.jmatprotec.2008.03.027 ↗
13. Numerical simulation and optimization of low pressure die casting of aluminum alloy cylinder block
14. Gas entrainment behavior of aluminum alloy engine crankcases during the low-pressure-die-casting process10.1016/j.jmatprotec.2018.11.016 ↗
15. Effect of Zr, Er and Cr additions on microstructures and properties of Al–Zn–Mg–Cu alloys10.1016/j.msea.2014.05.021 ↗
16. Influence of alloyed Sc and Zr, and heat treatment on microstructures and stress corrosion cracking of Al–Zn–Mg–Cu alloys10.1016/j.msea.2014.10.058 ↗
17. Influence of process parameters and sr addition on the microstructure and casting defects of LPDC A356 Alloy for engine blocks10.1016/j.jmst.2016.03.010 ↗
18. Low-pressure die casting of magnesium alloy AM50: response to process parameters10.1016/j.jmatprotec.2007.11.111 ↗
19. Effect of holding pressure on density and cooling rate of cast Al-Si alloy during additive pressure casting10.1007/s41230-019-9085-7 ↗
20. Effect of process parameters on porosity distributions in high-pressure die-cast AM50 Mg-alloy10.1016/j.msea.2006.04.082 ↗
21. On the influence of process variables on the thermal conditions and properties of high pressure die-cast magnesium alloys10.1016/S0924-0136(97)00221-5 ↗
22. An investigation on the microstructure and tensile properties of direct squeeze cast and gravity die cast 2024 wrought Al alloy10.1016/j.matdes.2008.04.012 ↗
23. Squeeze casting: an overview10.1016/S0924-0136(99)00291-5 ↗
24. Effect of pressure on microstructures and mechanical properties of Al-Cu-based alloy prepared by squeeze casting10.1016/S1003-6326(07)60122-8 ↗
25. The study on microstructures and properties of the direct squeeze casting Al-Zn-Mg-Cu-Zr-Sc alloy, advanced materials research
26. Effect of the gap distance on the cooling behavior and the microstructure of indirect squeeze cast and gravity die cast 5083 wrought Al alloy10.1016/S0921-5093(02)00054-0 ↗
27. Studies on the microstructures and properties in phase transformation of homogenized 7050 alloy10.1016/j.msea.2014.06.027 ↗
28. Substitution of Cu and/or Al in η phase (MgZn2) and the implications for precipitation in Al–Zn–Mg–(Cu) alloys10.1016/j.intermet.2014.01.012 ↗
29. Influence of Zr content on microstructure and mechanical properties of As-cast Al-Zn-Mg-Cu alloy10.1016/j.jallcom.2021.158920 ↗