journal article·2025-01

Microstructure and mechanical properties of strength-ductility synergetic SiC/ZK60 composites by a pre-dispersion strategy

Yinghao Feng, Chaoyang Sun, Sinuo Xu, Jingchen Liu, Lingyun Qian

Publisher page

Abstract

The strength-ductility trade-off presents a significant challenge in the development of magnesium matrix composites (MMCs). A novel strategy that combines powder pre-dispersion, nano-SiC/Al master alloy sintering, stir casting, and hot extrusion combined method was introduced to prepare the strength-ductility synergetic SiC/ZK60 composites. The microstructural evolution and mechanical properties of these composites have been thoroughly investigated and compared. The results demonstrate that SiC particles are uniformly distributed within the as-solution-treated composites, and extrusion processes promote cluster refinement. Microstructural characterization shows that adding nano-SiC/Al enhances grain refinement and facilitates the precipitation of secondary phases. The grain refinement is attributed to the accelerated dynamic recrystallization (DRX) and nano-particle pinning, where particle stimulated nucleation (PSN), continue DRX (CDRX), and discontinue DRX (DDRX) are the dominant DRX mechanisms of composites. This process is further enhanced by increased nucleation sites induced by SiC, which facilitate the precipitation of MgZn 2 and Zr phases. Additionally, a microscale Al 3Zr phase precipitates within the composites due to aluminum addition. Notably, both strength and ductility, as well as elastic modulus (E) of 10SiC/ZK60 and 20SiC/ZK60 composites were improved simultaneously, with optimal ultimate tensile strength and elongation (EL) increasing by nearly 10 %. Grain refinement emerges as a primary factor contributing to enhanced mechanical properties. Also, load transfer and stress release caused by multiple crack sources contribute significantly to strength and ductility strengthening, respectively.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (52)

Show source-provided references
1. Evolutions of microstructure and mechanical properties for Mg-Al/AlN composites under hot extrusion10.1016/j.msea.2016.05.033 ↗
2. Ultra-high tensile strength induced by multiple precipitates in extruded ZK60 alloy via co-alloying Ca and Er10.1016/j.jallcom.2023.172680 ↗
3. The performance of nano-Y2O3-reinforced ZK60 matrix nanocomposites prepared by powder metallurgy10.1016/j.matdes.2023.112492 ↗
4. Low-cost high-strength Mg-7Zn-xAl-0.3Mn (x=1, 3, 5) cast magnesium alloys via grain boundary strengthening and precipitation strengthening10.1016/j.msea.2023.145664 ↗
5. Improved wear and friction properties by self-formed SiC layers in Mg/SiC composites10.1016/j.ceramint.2024.05.333 ↗
6. Texture development and tensile properties of Mg-Yb binary alloys during hot extrusion and subsequent annealing10.1016/j.jma.2021.05.001 ↗
7. Mechanical, biodegradability and biocompatibility behaviour of seashell and ZrO2 particulates reinforced AZ31 Mg composites10.1016/j.ceramint.2024.02.040 ↗
8. Effect of SiC nanoparticle content and milling time on the microstructural characteristics and properties of Mg-SiC nanocomposites synthesized with powder metallurgy incorporating high-energy ball milling10.1016/j.ceramint.2020.07.173 ↗
9. Microstructure and mechanical properties of SiC particle reinforced magnesium composites processed by injection molding10.1016/j.msea.2011.04.088 ↗
10. Microstructure and room temperature tensile properties of 1 μm-SiCp/AZ31B magnesium matrix composite10.1016/j.jma.2015.03.001 ↗
11. Microstructure and strengthening mechanism of bimodal size particle reinforced magnesium matrix composite10.1016/j.compositesa.2012.03.007 ↗
12. Grain refinement mechanism of SiC nanoparticles/Mg-9 wt% Al composite investigated by sharp interface model at microscale and nanoscale10.1016/j.jallcom.2022.166269 ↗
13. Microstructure and tribological properties of as-cast and multi-pass friction stir processed Mg-0.5Zn-0.5Zr/SiC composite fabricated by stir casting technique10.1016/j.jmrt.2023.11.205 ↗
14. Processing and properties of magnesium containing a dense uniform dispersion of nanoparticles10.1038/nature16445 ↗
15. Different effects of SiC dimensions on the microstructure and mechanical properties of magnesium matrix composites10.1016/j.msea.2022.143273 ↗
16. The investigation of strength-ductility mechanism of bimodal size SiCp/Mg–Zn matrix composite10.1016/j.ceramint.2024.06.046 ↗
17. Strengthening of Mg-Al-Zn-Mn alloy using SiC/Al nanocomposite extrusion10.1016/j.jallcom.2022.166243 ↗
18. Achieving high strength and modulus in graphene reinforced Mg matrix composites via an in-situ process10.1016/j.msea.2022.143713 ↗
19. Microstructure characteristics and enhanced tensile properties of in-situ AlN/AZ91 composites prepared by liquid nitriding method10.1016/j.msea.2018.03.126 ↗
20. Achieving high strength-ductility combination and negligible yield asymmetry in extruded AlN/AZ91 composite rods10.1016/j.msea.2019.138842 ↗
21. Simultaneously enhancing the strength and ductility of as-extruded AlN/AZ91 composites via nano-precipitation and pyramidal slip10.1016/j.jmst.2023.06.039 ↗
22. Investigation into the fracture behavior of ZK60 Mg alloy rolling sheet under different stress triaxiality10.1016/j.jmrt.2023.11.202 ↗
23. Role of second phases and grain boundaries on dynamic recrystallization behavior in ZK60 magnesium alloy10.1016/j.jallcom.2020.157958 ↗
24. Development of high performance magnesium matrix nanocomposites using nano-SiC particulates as reinforcement10.1007/s11665-015-1707-7 ↗
25. Twinning, dynamic recrystallization, and texture evolution in as-solution AZ80 Mg alloy during hot compression10.1016/j.jmrt.2023.07.004 ↗
26. Microstructure, mechanical properties and wear resistance of Ti particles reinforced AZ31 magnesium matrix composites10.1016/j.jma.2022.06.012 ↗
27. The role of initial grain size on bimodal-grained microstructure and mechanical properties of an extruded Mg-Gd-Y-Nd-Zr alloy10.1016/j.jmrt.2023.02.056 ↗
28. Microstructure evolution and fracture behaviour of TWIP steel under dynamic loading10.1016/j.msea.2022.143657 ↗
29. Dynamic precipitation and enhanced mechanical properties of ZK60 magnesium alloy achieved by low temperature extrusion10.1016/j.msea.2021.142143 ↗
30. Evaluation of whisker alignment and anisotropic mechanical properties of ZK60 alloy reinforced with SiCw during KOBO extrusion method10.1016/j.jmapro.2022.10.012 ↗
31. Tensile properties and microstructure of ZK60/SiCw composite after extrusion and aging10.1016/j.jallcom.2020.154709 ↗
32. Achieving high-strength magnesium matrix nanocomposite through synergistical effect of external hybrid (SiC+TiC) nanoparticles and dynamic precipitated phase10.1016/j.jallcom.2018.09.030 ↗
33. Aging behavior of AZ91 matrix influenced by 5 μm SiCp: Investigation on the microstructure and mechanical properties10.1016/j.jallcom.2017.08.198 ↗
34. Microstructure evolution and mechanical properties of nano-SiCp/AZ91 composite processed by extrusion and equal channel angular pressing (ECAP)10.1016/j.matchar.2016.10.003 ↗
35. Evolutions of microstructure and mechanical properties for SiCp/AZ91 composites with different particle contents during extrusion10.1016/j.msea.2015.03.058 ↗
36. Adding TiC nanoparticles to magnesium alloy ZK60A for strength/ductility enhancement10.1155/2011/642980 ↗
37. Characteristic zirconium-rich coring structures in Mg-Zr alloys10.1016/S1359-6462(02)00046-5 ↗
38. Influence of NbC particles on microstructure and mechanical properties of AlCoCrFeNi high-entropy alloy coatings prepared by laser cladding10.1016/j.jallcom.2019.02.223 ↗
39. Classification of bulk metallic glasses by atomic size difference, heat of mixing and period of constituent elements and its application to characterization of the main alloying element10.2320/matertrans.46.2817 ↗
40. Characterization and corrosion behavior of composites reinforced with ZK60, AlN, and SiC particles
41. Heterogeneous fiberous structured Mg-Zn-Zr alloy with superior strength-ductility synergy10.1016/j.jmst.2022.06.021 ↗
42. Effects of nanosized TiCp dispersion on the high-temperature tensile strength and ductility of in situ TiCp/Al-Cu-Mg-Si nanocomposites10.1016/j.jallcom.2018.10.052 ↗
43. Towards the work hardening and strain delocalization achieved via in-situ intragranular reinforcement in Al-CuO composite10.1016/j.actamat.2023.119110 ↗
44. Adiabatic shear localization induced by dynamic recrystallization in an FCC high entropy alloy10.1016/j.ijplas.2023.103550 ↗
45. Study on the dynamic recrystallization mechanisms of Inconel 740 superalloy during hot deformation10.1016/j.jallcom.2019.153325 ↗
46. Grain refinement of magnesium alloys by dynamic recrystallization (DRX): a review10.1016/j.jmrt.2023.07.150 ↗
47. Mechanical properties and tribological behavior of magnesium metal matrix composites with micron-sized and nano-sized reinforcements
48. Magnesium matrix composite reinforced by nanoparticles - a review10.1016/j.jma.2020.08.018 ↗
49. Microstructure, mechanical properties and fracture toughness of ECAPed magnesium matrix composite reinforced with hydroxyapatite ceramic particulates for bioabsorbable implants10.1016/j.ceramint.2023.02.069 ↗
50. Effect of Yb addition on the microstructure and mechanical properties of ZK60 alloy during extrusion10.1016/j.msea.2020.139033 ↗
51. Effect of nanoscale boron carbide particle addition on the microstructural evolution and mechanical response of pure magnesium10.1016/j.matdes.2013.11.031 ↗
52. Enhancing strength and ductility of Al-matrix composite via a dual-heterostructure strategy10.1016/j.ijplas.2023.103825 ↗