Overcoming the strength-ductility tradeoff of a 3D-printed Al-Si alloy by equal channel angular pressing
Source abstract
Abstract
The integration of additive manufacturing and severe plastic deformation has produced an Al-Si alloy with superior mechanical properties. The novel processing pathway effectively avoids strength-ductility trade-off, resulting in an elongation increase of three times while maintaining a comparable yield strength to that of the original condition. The implementation of an intermediate annealing heat treatment (HT) before the subsequent equal channel angular pressing (ECAP) processing resulted in the most favorable combinations of strength and ductility. The ECAP process transformed the ultrafine interconnected eutectic network into ultrafine particles. This process also led to the formation of a heterogeneous grain size and the transformation of the 3-dimensional network of aluminides (Al2Cu) and Si-enriched precipitates into particles with varying sizes, ranging from 4¿nm to 500¿nm. In contrast, the ECAP processing without an intermediate annealing heat treatment led to a maximum yield strength increment of 22%. Notably, this enhancement in strength was achieved while preserving comparable levels of elongation to those observed in the as-built material. Hence, achieving the optimal combination of yield strength and ductility ratio demands a careful balance between various strengthening mechanisms, including subgrains and precipitates.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Microstructure and mechanical properties · Additive Manufacturing Materials and Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (69)
Show source-provided references
1. Material-structure-performance integrated laser-metal additive manufacturing10.1126/science.abg1487 ↗
2. Superior mechanical properties of a selective-laser-melted AlZnMgCuScZr alloy enabled by a tunable hierarchical microstructure and dual-nanoprecipitation10.1016/j.mattod.2021.11.019 ↗
3. Opportunities and challenges in additive manufacturing of functionally graded metallic materials via powder-fed laser directed energy deposition: a review10.1016/j.jmatprotec.2021.117117 ↗
4. Material issues in additive manufacturing: a review10.1016/j.jmapro.2016.11.006 ↗
5. The Future of Metals10.1126/science.1185866 ↗
6. Effect of heat treatments on the mechanical and microstructural behavior of a hypoeutectic Al alloy obtained by laser powder bed fusion10.1016/j.msea.2022.144091 ↗
7. Comparative study on wire-Arc additive manufacturing and conventional casting of Al–Si alloys: porosity, microstructure and mechanical property10.1007/s40195-021-01314-1 ↗
8. Melt pool temperature and cooling rates in laser powder bed fusion
9. 3D printing of high-strength aluminium alloys10.1038/nature23894 ↗
10. Additive manufacturing of metallic and ceramic components by the material extrusion of highly-filled polymers: a review and future perspectives10.3390/ma11050840 ↗
11. Influence of sub-cell structure on the mechanical properties of AlSi10Mg manufactured by laser powder bed fusion10.1016/j.msea.2020.138976 ↗
12. Heterogeneity consequences on the mechanical and microstructural evolution of an AlSi11Cu alloy obtained by selective laser melting10.1016/j.matchar.2021.110989 ↗
13. Review on the correlation between microstructure and mechanical performance for laser powder bed fusion AlSi10Mg
14. The origin of high-density dislocations in additively manufactured metals10.1080/21663831.2020.1751739 ↗
15. Review on field assisted metal additive manufacturing10.1016/j.ijmachtools.2023.104032 ↗
16. Characterization of the gas tungsten arc welding (GTAW) joint of armco iron nanostructured by equal-channel angular pressing (ECAP)10.1016/j.jmatprotec.2020.116902 ↗
17. Equal channel angular sheet extrusion (ECASE) produces twinning heterogeneity in commercially pure titanium10.1016/j.matchar.2021.111460 ↗
18. Severe plastic deformation through high-pressure torsion for preparation of hydrogen storage materials -a review10.2320/matertrans.MT-MF2022039 ↗
19. The hot deformation behaviour of laser powder bed fusion deposited Al–Si–Cu alloy processed by high-pressure torsion10.1007/s10853-022-07847-9 ↗
20. Microstructural and hardness evolution of additively manufactured Al–Si–Cu alloy processed by high-pressure torsion10.1007/s10853-022-07234-4 ↗
21. Significance of grain refinement on micro-mechanical properties and structures of additively-manufactured CoCrFeNi high-entropy alloy10.1016/j.msea.2021.140898 ↗
22. Severe plastic deformation as a processing tool for strengthening of additive manufactured alloys10.1016/j.jmapro.2021.05.070 ↗
23. Overcoming the strength-ductility trade-off in additively manufactured AlSi10Mg alloy by ECAP processing10.1016/j.jallcom.2022.165817 ↗
24. Improving density and strength-to-ductility ratio of a 3D-printed Al–Si alloy by high-pressure torsion10.1007/s10853-023-09298-2 ↗
25. In situ heating neutron and X-Ray diffraction analyses for revealing structural evolution during postprinting treatments of additive-manufactured 316L stainless steel10.1002/adem.202270017 ↗
26. In situ neutron diffraction investigating microstructure and texture evolution upon heating of nanostructured CoCrFeNi high-entropy alloy
27. Heterostructured materials10.1016/j.pmatsci.2022.101019 ↗
28. Heterogeneous materials: a new class of materials with unprecedented mechanical properties10.1080/21663831.2017.1343208 ↗
29. Y. Zhu, X. Wu, Chapter Six - Heterostructured materials: Processing techniques, properties, and potential applications, in: Y. Zhu, X. Wu (Eds.), Introd. to Heterostruct. Mater., Elsevier, 2023: pp. 121–162. https://doi.org/https://doi.org/10.1016/B978-0-323-99326-5.00007-5.10.1016/B978-0-323-99326-5.00007-5 ↗
30. Low-dimensional hard magnetic materials10.1016/j.pmatsci.2023.101143 ↗
31. Influence of the radial-shear rolling (RSR) process on the microstructure, electrical conductivity and mechanical properties of a Cu–Ni–Cr–Si alloy10.1016/j.msea.2021.141676 ↗
32. Dislocation array reflection enhances strain hardening of a dual-phase heterostructured high-entropy alloy10.1080/21663831.2023.2208166 ↗
33. Exceptional cryogenic strength and sufficient ductility of a nanotwinned high-entropy alloy fabricated by cryogenic multi-directional compression10.1016/j.jallcom.2022.167533 ↗
34. Adiabatic shear localization induced by rotationally accelerated shot peening10.1007/s10853-023-08152-9 ↗
35. Microstructure and properties of novel AlSi11CuMn alloy manufactured by selective laser melting10.1016/j.matlet.2018.04.077 ↗
36. The effects of selective laser melting process parameters on relative density of the AlSi10Mg parts and suitable procedures of the archimedes method10.3390/app9030583 ↗
37. Resolving the geometrically necessary dislocation content by conventional electron backscattering diffraction10.1016/j.scriptamat.2008.01.050 ↗
38. Dragonfly | 3D Visualization and Analysis Solutions for Scientific and Industrial Data | ORS, (n.d.). https://www.theobjects.com/dragonfly/index.html (accessed June 21, 2023).
39. Principle of equal-channel angular pressing for the processing of ultra-fine grained materials10.1016/1359-6462(96)00107-8 ↗
40. Influence of specimen dimensions on the tensile behavior of ultrafine-grained Cu10.1016/j.scriptamat.2008.05.031 ↗
41. Microstructure characterization of metallic materials processed by equal channel angular pressing (ECAP): an electron backscatter diffraction (EBSD) analysis10.2320/matertrans.MT-MF2022042 ↗
42. Evidence for a stable single component sharp texture in high purity aluminum during tube high-pressure shearing at room temperature
43. Continuous dynamic recrystallization during severe plastic deformation10.1016/j.mechmat.2015.05.008 ↗
44. A review of dynamic recrystallization phenomena in metallic materials10.1016/j.matdes.2016.09.012 ↗
45. Plastic behavior and microstructure heterogeneity of an AA6063-T6 aluminum alloy processed by symmetric and asymmetric rolling
46. Microstructure and strengthening mechanisms in an Al-Mg-Si alloy processed by equal channel angular pressing (ECAP)10.1007/s00170-017-1310-1 ↗
47. Texture evolution in equal-channel angular extrusion10.1016/j.pmatsci.2009.01.001 ↗
48. S.H. Huo, M. Qian, G.B. Schaffer, E. Crossin, 21 - Aluminium powder metallurgy, in: R. Lumley (Ed.), Fundam. Alum. Metall., Woodhead Publishing, 2011: pp. 655–701. https://doi.org/https://doi.org/10.1533/9780857090256.3.655.10.1533/9780857090256.3.655 ↗
49. Microstructure and mechanical properties of AA6082-T6 by ECAP under warm processing
50. III. Dislocation densities in some annealed and cold-worked metals from measurements on the X-ray debye-scherrer spectrum
51. Recent findings in superior strength and ductility of ultrafine-grained materials10.14723/tmrsj.40.309 ↗
52. The precipitation sequence in Al–Mg–Si alloys10.1016/S1359-6454(98)00059-7 ↗
53. Effect of heat treatment process and optimization of its parameters on mechanical properties and microstructure of the AlSi11(Fe) alloy10.3390/ma14092391 ↗
54. Back stress strengthening and strain hardening in gradient structure10.1080/21663831.2016.1153004 ↗
55. Influence on microstructure, strength and ductility of build platform temperature during laser powder bed fusion of AlSi10Mg10.1016/j.actamat.2020.10.001 ↗
56. Design approaches for printability-performance synergy in Al alloys for laser-powder bed additive manufacturing10.1016/j.matdes.2021.109640 ↗
57. Ductility and plasticity of nanostructured metals: differences and issues10.1016/j.mtnano.2018.09.004 ↗
58. Melt pool boundaries in additively manufactured AlSi10Mg: Correlating inhomogeneous deformation with local microstructure via in-situ microtensile tests10.1016/j.msea.2023.145431 ↗
59. Load partition during hot deformation of AlSi12 and AlSi10Cu6Ni2 alloys: a quantitative evaluation of the stiffness of Si networks10.1007/s10853-020-05023-5 ↗
60. Breaks in the Hall–Petch relationship after severe plastic deformation of magnesium, aluminum, copper, and iron10.3390/cryst13030413 ↗
61. E.T. George, D.S. MacKenzie, Handbook of aluminum. Physical Metallurgy and Processes, Marcel Dek, New York, 2003.
62. A modified Hall–Petch relationship in ultrafine-grained titanium recycled from chips by equal channel angular pressing10.1016/j.scriptamat.2012.02.008 ↗
63. High cycle fatigue of ARMCO iron severely deformed by ECAP10.1016/j.msea.2016.10.010 ↗
64. Hall–Petch relation and boundary strengthening10.1016/j.scriptamat.2004.06.002 ↗
65. Mechanical behavior and strengthening mechanisms in ultrafine grain precipitation-strengthened aluminum alloy10.1016/j.actamat.2013.09.042 ↗
66. Coupling effect of multiple precipitates on the ductile fracture of aged Al–Mg–Si alloys10.1016/j.scriptamat.2007.06.063 ↗
67. Sequential modeling of local precipitation, strength and strain hardening in friction stir welds of an aluminum alloy 6005A-T610.1016/j.actamat.2007.07.012 ↗
68. Stress partitioning behavior of an AlSi10Mg alloy produced by selective laser melting during tensile deformation using in situ neutron diffraction10.1016/j.jallcom.2016.06.011 ↗
69. Extreme shear-deformation-induced modification of defect structures and hierarchical microstructure in an Al–Si alloy10.1038/s43246-020-00087-x ↗