journal article·2023-06

Mechanical properties and microstructure evolution of 2219 aluminum alloy via electromagnetic ring expansion & electromagnetic treatment

Huijuan Ma, Wenjie Mao, Ning Zhao, Hui Zhu, Peiliao Wang, Qian Sun, Zhili Hu, Liang Huang, Jianjun Li

Publisher page

Abstract

As an emerging technology to solve the bottleneck of plastic processing of light alloys, electromagnetic forming usually causes a complex mechanical response and microstructure evolution of materials. In this work, based on the electromagnetic ring expansion (EMRE) experiment, the relationship between microstructure evolution and mechanical properties of AA2219-T6 under EMRE with different discharge energies is established. In particular, to reveal the influence of strain and temperature parameters on the output response during the electromagnetic pulse process, a Q235 steel sleeve and an epoxy resin sleeve with different thermal conductivities are applied to constrain the deformation of the ring, respectively, thus the performance under electromagnetic treatment (EMT) are investigated. It is found that, under the threshold discharge energy of 4.23 kJ, the microhardness of the ring via EMT with the steel sleeve is similar to that of AA2219-T6, but increases by 20.9% compared with the ring via EMT with the epoxy sleeve and 17.1% compared with the ring via EMRE. The electromagnetic pulse has no significant effect on the evolution of precipitates in AA2219-T6-EMT (Steel), but the adiabatic temperature rise in AA2219-T6-EMT (Epoxy) caused redissolution of G.P.Ⅱ zones. With the gradual increase of discharge energy under EMRE, the microhardness of AA2219-T6 increases initially and followed by a decrease, while the fracture strain increases continuously. When discharge energy reaches 8.63 kJ, 2219 aluminum alloy has the optimal mechanical properties that, compared with AA2219-T6, the microhardness increased by 14.2% and the fracture strain increased by 18.0%. The dislocation density shows a trend of first increasing and then decreasing with the increase of discharge energy. Combined with the observed phase transformation, it is shown that dislocations generated by EMRE will promote G.P.Ⅱ zones to transform into θ ′′ phases, and affected by dislocation density, the transformation effect is most obvious at 8.63 kJ. In addition, the transformation of precipitates greatly increases the probability of hindering the motion of dislocations, which promotes the precipitates to be dispersed, and AA2219-T6 is further strengthened after EMRE. As discharge energy continues to increase, the dislocations begin to annihilate and G.P.Ⅱ zones are redissolved due to the adiabatic temperature rise.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Electromagnetic Effects on Materials · Microstructure and mechanical properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (46)

Show source-provided references
1. Enhanced mechanical properties of high-temperature-resistant Al–Cu cast alloy by microalloying with Mg10.1016/j.jallcom.2020.154305 ↗
2. Effects of segmented thermal-vibration stress relief process on residual stresses, mechanical properties and microstructures of large 2219 Al alloy rings10.1016/j.jallcom.2021.161269 ↗
3. Strengthening mechanism in laser-welded 2219 aluminium alloy under the cooperative effects of aging treatment and pulsed electromagnetic loadings10.1016/j.msea.2017.12.081 ↗
4. Modified kinetic model for describing continuous dynamic recrystallization behavior of Al 2219 alloy during hot deformation process10.1016/j.jallcom.2019.153301 ↗
5. High-speed incremental forming–new technologies for flexible production of sheet metal parts10.1016/j.promfg.2018.12.038 ↗
6. Electromagnetic forming—a review10.1016/j.jmatprotec.2010.12.012 ↗
7. Enhanced formability and hardness of AA2195-T6 during electromagnetic forming10.1016/j.jallcom.2021.161891 ↗
8. Precipitation behavior of an Al–Cu alloy during isothermal aging at low temperatures10.1016/j.matlet.2004.10.058 ↗
9. Influence of pre-deformation and subsequent ageing on the hardening behavior and microstructure of 2219 aluminum alloy forgings10.1016/j.jallcom.2016.06.111 ↗
10. The effect of ingot processing treatments on the grain size and properties of Al alloy 707510.1007/BF02644652 ↗
11. Effect of pre-deformation on the microstructures and properties of 2219 aluminum alloy during aging treatment10.1016/j.jallcom.2016.12.006 ↗
12. Effects of cold predeformation on dissolution of second-phase Al2Cu particles during solution treatment of 2219 Al-Cu alloy forgings10.1016/j.matchar.2017.10.026 ↗
13. Effects of deformation temperature on second-phase particles and mechanical properties of 2219 Al-Cu alloy10.1016/j.msea.2017.11.124 ↗
14. Electromagnetic impulse calibration of high strength sheet metal structures10.1016/j.jmatprotec.2010.05.013 ↗
15. Lightweight in automotive components by forming technology10.1007/s42154-020-00103-3 ↗
16. Rate-related study on mechanical properties and fracture characteristics in aluminium alloy via electromagnetic ring expansion test10.1016/j.ijmecsci.2021.106712 ↗
17. Increased ductility in high velocity electromagnetic ring expansion10.1007/BF02651933 ↗
18. Expansion fracture mode of 7075 aluminum ring under electromagnetic loading
19. Ductility of selected metals under electromagnetic ring test loading conditions10.1016/j.ijsolstr.2012.01.005 ↗
20. Y. Wan, J.W. Wu, Z.L. Wu, X.T. Han, Q. Chen, Q.L. Cao, Simulation Research on Necking and Fracture of Electromagnetic Expanding Ring Based on Gurson Model[C]//2020 IEEE 1st China International Youth Conference on Electrical Engineering (CIYCEE). IEEE, (2020) 1–6.〈https://doi.org/10.1109/CIYCEE49808.2020.9332562〉.10.1109/CIYCEE49808.2020.9332562 ↗
21. Effect of electromagnetic ring expansion on the mechanical property of A5083 aluminum alloy10.1109/TASC.2013.2288095 ↗
22. Effect of the electron state of a metal on its mechanical properties and the phenomenon of electroplasticity
23. Application of high-density current in plastic working of metals10.1002/pssa.2210520109 ↗
24. Electric current-induced annealing during uniaxial tension of aluminum alloy10.1016/j.scriptamat.2013.11.019 ↗
25. Influence of electric current on superplastic deformation mechanism of 5083 aluminium alloy10.1179/1743284715Y.0000000120 ↗
26. Low energy electroplasticity in aluminum alloys10.1016/j.msea.2020.140235 ↗
27. Formability of AA 2219-O sheet under quasi-static, electromagnetic dynamic, and mechanical dynamic tensile loadings10.1016/j.jmst.2020.07.023 ↗
28. Microstructural evolution and mechanical properties of 2219 aluminum alloy from different aging treatments to subsequent electromagnetic forming10.1016/j.matchar.2021.111470 ↗
29. On the dynamics of necking and fragmentation-I. Real-time and post-mortem observations in Al 6061-O10.1007/s10704-006-9024-7 ↗
30. Age hardening behaviors of spun 2219 aluminum alloy component10.1016/j.jmrt.2020.02.098 ↗
31. A calorimetric study of precipitation in aluminum alloy 221910.1007/BF02655200 ↗
32. Grain refinement in 7075 aluminum by thermomechanical processing10.1007/BF02642340 ↗
33. Evolution of precipitates in ZK60 magnesium alloy during high strain rate deformation10.1016/j.jallcom.2017.02.158 ↗
34. Analysis of enhanced diffusivity in nickel10.1063/1.1713880 ↗
35. Enhanced diffusion during plastic deformation by mechanical diffusion10.1063/1.1709056 ↗
36. Diffusive transformation at high strain rate: on instantaneous dissolution of precipitates in aluminum alloy during adiabatic shear deformation10.1557/jmr.2016.151 ↗
37. Precipitation thermodynamics and kinetics of the second phase of Al–Zn–Mg–Cu–Sc–Zr–Ti aluminum alloy10.1016/j.jmrt.2020.11.075 ↗
38. Effect of initial microstructure on the hot compression deformation behavior of a 2219 aluminum alloy10.1016/j.matdes.2011.07.061 ↗
39. Precipitates and intermetallic phases in precipitation hardening Al–Cu–Mg–(Li) based alloys10.1179/174328005X14357 ↗
40. Effects of pre-deformation on the microstructures and corrosion behavior of 2219 aluminum alloys10.1016/j.msea.2018.03.041 ↗
41. Microstructure evolution and mechanical behavior of a binary Al–7Mg alloy processed by equal-channel angular pressing10.1016/j.actamat.2014.10.025 ↗
42. Microstructure, residual stress and tensile properties control of wire-arc additive manufactured 2319 aluminum alloy with laser shock peening10.1016/j.jallcom.2018.02.353 ↗
43. Study on cryorolled Al–Cu alloy using X-ray diffraction line profile analysis and evaluation of strengthening mechanisms10.1016/j.matdes.2013.05.095 ↗
44. The effect of dislocation contrast on X-ray line broadening: a new approach to line profile analysis10.1063/1.117951 ↗
45. A process model for age hardening of aluminium alloys—I. The model10.1016/0956-7151(90)90291-N ↗
46. An age hardening model for Al–7Si–Mg casting alloys10.1016/S0921-5093(01)01479-4 ↗