journal article·2024-09

Effect of gadolinium on the machinability of an Al-killed high sulfur steel

Hong Wei, Shengchao Duan, Lifeng Zhang

Publisher page

Abstract

The effect of various gadolinium contents on the number density and morphology of sulfide in Al-killed high-sulfur steel was investigated. Meanwhile, the effect of characterization of sulfide inclusions, i.e., number density and morphology on the cutting performance of steel also were studied. The evolution process of sulfide inclusions with the increasing T.Gd content from 0 ppm to 198 ppm in steel samples could be described as follows: MnS → (Gd-O-S)-MnS→(Gd-S)-MnS →Gd-S. As the gadolinium content in the steel increased, sulfide inclusions with an aspect ratio of < 3 increased from 26.1 % to 99.7 % and the number density of sulfides decreased from 438 #/mm 2 to 80.4 #/mm 2 . Spherical sulfides could form micro-holes during cutting, facilitating the chip-breaking process, whereas long-strip MnS tended to self-break during cutting. The higher the proportion of C-type chips in the cutting process, the better the cutting performance of the material. Therefore, spherical sulfides exhibited superior modification effects on surface finishes compared to long-strip sulfides. In low-speed cutting, sulfide morphology predominantly affected surface roughness, while in high-speed cutting, the number density of sulfides became the dominant factor. The addition of gadolinium can effectively decrease the surface roughness of the material at various cutting parameters. Moreover, the Gd-O film can be formed on the tool surface was observed after the addition of gadolinium in the steel, which can increase the lubrication during the cutting process and reduce the tool surface wear.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallurgical Processes and Thermodynamics · Advanced machining processes and optimization · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (67)

Show source-provided references
1. Deep analysis of free-cutting phase and its distribution in japanese SF20T pen tip steel10.1088/1757-899X/611/1/012019 ↗
2. Inclusions modification and improvement of machinability in a non-quenched and tempered steel with Mg treatment10.1051/metal/2020021 ↗
3. Wear and MnS layer adhesion in uncoated cutting tools when dry and wet turning free-cutting steels10.3390/met9050556 ↗
4. Wear reduction mechanisms in modulated turning of compacted graphite iron with coated carbide tool10.1016/j.triboint.2022.108062 ↗
5. Effect of MnS inclusions on plastic deformation and fracture behavior of the steel matrix at high temperature
6. Inclusion deformation and toughness anisotropy in hot-rolled steels10.1179/030716976803391656 ↗
7. Study on transverse-longitudinal fatigue properties and their effective-inclusion-size mechanism of hot rolled bearing steel with rare earth addition10.1016/j.ijfatigue.2019.105193 ↗
8. Effect of S content on the MnS precipitation in steel with oxide nuclei10.2355/isijinternational.36.1014 ↗
9. Effect of sulfur content and solidification variables on morphology and distribution of sulfide in steel ingots10.2355/isijinternational1966.18.564 ↗
10. Effect of titanium addition on the formation and distribution of MnS inclusions in steel during solidification10.2355/isijinternational.37.332 ↗
11. Consideration on distribution and size of dendritic type II MnS-inclusion in steel dendrite structure10.2355/isijinternational.34.992 ↗
12. Study on mitigating center macro-segregation during steel continuous casting process10.1002/srin.201100085 ↗
13. Formation of manganese sulfide in steel10.2355/isijinternational1966.21.477 ↗
14. Mechanical anisotropy and local ductility in transverse tensile deformation in hot rolled steels: the role of MnS inclusions10.1016/j.msea.2018.12.026 ↗
15. Spheroidization of type II manganese sulfides by heat treatment10.1007/BF02648360 ↗
16. Effect of heat treatment conditions on shape control of large-sized elongated MnS inclusions in resulfurized free-cutting steels10.2355/isijinternational.51.1995 ↗
17. Morphology study on inclusion modifications using Mg–Ca treatment in resulfurized special steel10.3390/ma12020197 ↗
18. A review of research on MnS inclusions in high-quality steel
19. The effect of tellurium on the formation of MnTe-MnS composite inclusions in non-quenched and tempered steel10.3390/met8080639 ↗
20. Study on the high-temperature evolution and formation mechanism of inclusions in Te-treated resulfurized special steel10.1002/srin.202100235 ↗
21. Morphology and composition characteristics of solid solution in Te-treated Y1Cr17 steel
22. Enhancement of impurity, machinability and mechanical properties in Te-treated 0Cr18Ni9 steel10.1007/s12540-019-00545-3 ↗
23. Deformation of MnS–MnTe inclusions in a sulfur-containing free-cutting steel with tellurium treatment10.1007/s11663-022-02698-w ↗
24. Effect of bismuth and telluride on the inclusions of sulfur free-cutting steel
25. Bi-sulfide existence in 0Cr18Ni9 steel: correlation with machinability and mechanical properties10.1016/j.jmrt.2020.06.043 ↗
26. Effect of Al2O3 content in inclusions on the precipitation of MnS during cooling of a heavy rail steel10.1007/s11663-023-02773-w ↗
27. Experimental study on rare earth and magnesium composite treatment of 49MnVS3 non-quenched and tempered steel10.1002/srin.202100190 ↗
28. Modification of sulfides in a high sulfur steel by cerium addition10.1007/s11663-022-02660-w ↗
29. Effect of La content on inclusion morphology in automobile sulfur-containing gear steel SCr420H10.1002/srin.202300127 ↗
30. Development of high impact toughness offshore engineering steel by yttrium-based rare earth addition10.1080/03019233.2021.1996181 ↗
31. Effect of rare earth Yttrium on the hot ductility of eco-friendly Bi-S based free cutting steel10.1515/htmp-2013-0077 ↗
32. Effect of lanthanum and cerium on inclusions in GCr15 bearing steel10.1007/s12666-022-02572-y ↗
33. Effect of rare earth cerium content on manganese sulfide in U75V heavy rail steel10.3390/met12061012 ↗
34. MnS-Pr2S3 phase diagram10.1134/S0036023610040182 ↗
35. Study on the machinability of two different sulfur free cutting steels10.4028/www.scientific.net/AMR.69-70.510 ↗
36. Effect of surfactant Te on the formation of MnS inclusions in steel10.1007/s11663-017-1050-5 ↗
37. Effect of volume fraction and shape of sulfide inclusions on through-thickness ductility and impact energy of high-strength 4340 plate steels10.1007/BF02648395 ↗
38. Sulfide shape control in high strength low alloy steels10.1007/BF03037861 ↗
39. Modification of MnS inclusion with trace tellurium to improve the machinability of medium-carbon low-sulfur steel10.1080/03019233.2023.2197526 ↗
40. An investigation on the machinability of newly developed low-carbon sulphurised free-cutting steels10.1177/0954405415599944 ↗
41. Study on the inner surface finishing of aluminum alloy 2014 by ball burnishing process10.1016/j.jmatprotec.2007.10.040 ↗
42. Modeling and analysis of surface roughness of microchannels produced by μ-WEDM using an ANN and Taguchi method10.1007/s12206-017-1039-7 ↗
43. The effect of inclusion composition on tool wear in hard part turning using PCBN cutting tools10.1016/j.wear.2015.04.008 ↗
44. Effect of S addition on mechanical and machinability properties in austenitic Fe–Mn–Al–C lightweight steels10.1016/j.msea.2022.143939 ↗
45. Effect of prealloyed MnS content and sintered density on machinability and mechanical properties
46. The effect of different non-metallic inclusions on the machinability of steels10.3390/ma8020751 ↗
47. Study on the machinability of two different sulfur free cutting steels10.4028/www.scientific.net/AMR.69-70.510 ↗
48. Thermodynamic analysis of sulfide precipitation in low-carbon high-sulfur high-phosphorus steels in solidification Process
49. M.L. Li Study on formation behavior and homogenization control of sulfide inclusions in free-cutting non-guenched and tempered steel 2015 University of Science and Technology Beijing.
50. Study on micro-machining mechanics based on direct SEM observation (2nd Report) dynamic crack behavior in shear type chip formation
51. Application of tellurium in free-cutting steels10.1007/s42243-018-0123-2 ↗
52. L. Yuan, Effect of rare earth Ce on cutting properties and mechanical properties of 42CrMo machined steel, in, Shenyang Ligong University, 2022.
53. Smelting process and machinability of BN-type free cutting steel
54. Study on micro-machining mechanics based on direct SEM observation (lst report) dynamic behavior of MnS inclusions during machining
55. Study on micro·machining mechanics based on direct SEM observation
56. Mechanism of the improvement of globular RE sulfide inclusions on the machinability
57. Investigation on the improvment of cutting properties of tool steels by the addition of rare earth elements
58. Summary of development of cutting tool coating technology at home and abroad
59. Effects of the composition, shape factor and area fraction of sulfide inclusions on the machinability of re-sulfurized free-machining steel10.1016/0924-0136(95)02144-2 ↗
60. An investigation of adhering layer formation during tool wear progression in turning of free-cutting stainless steel10.1016/0043-1648(96)06924-4 ↗
61. Development of wear-resistant coatings compounds for high-speed steel tool using a combined cathodic vacuum arc deposition
62. PVD/CVD technology for coating cemented carbides10.1016/0257-8972(94)02325-K ↗
63. K. Xue, Cutting performance appraisement and experiment study of coating tools, in, Shanghai Jiao Tong University, 2008.
64. Experimental study of built-up layer formation during machining of high strength free-cutting steel10.1016/j.jmatprotec.2016.05.016 ↗
65. Effect of oxide inclusions on machinability of free cutting steel with low carbon and high sulphur
66. Precipitation and control of BN inclusions in 42CrMo steel and their effect on machinability10.1007/s12613-013-0805-5 ↗
67. Effect of SiC addition to Al2O3 ceramics used in cutting tools10.3390/ma13225195 ↗