journal article·2023-03

Effects of vacuum hot-pressed sintering parameters on the microstructures and mechanical properties and process optimization of TiB2p/Al7050 composites

Yuelun Leng, Yong Hu, Mingxu Xu, Tong Wu, Shijie Liu, Hao Zhang, Nan Sun, Shen Liu

Publisher page

Abstract

In this paper, TiB 2p/Al7050 composites are studied, which lays a foundation for their development in aerospace materials and other fields. TiB 2p /Al7050 composites were prepared by vacuum hot-pressed sintering, and the process parameters were optimized based on an orthogonal experiment. The effects of sintering temperature A, axial pressure B, and holding time C on density, hardness, and strength are studied by range analysis, analysis of variance, and multi-index matrix analysis. The calculation shows that the order of influence of each factor is C>A>B, then the important parameters of holding time and sintering temperature were explored. The results show that the relative density, microhardness, and tensile strength of TiB 2p /Al7050 composites increase with the increase of holding time during sintering. Only the elongation increases first and then decreases at 600 °C, indicating that excessive holding time reduces the plasticity. The density, hardness, strength, and elongation increase first and then decrease with the increase in sintering temperature. Obvious porosity begins to appear after reaching 600 °C, resulting in performance degradation. The optimum process parameters were finally determined as 590 °C, 20 MPa, and 120 min, and the effects of other TiB 2 mass fraction composites on microstructure and mechanical properties were studied to verify the superiority of the process. With the increase of TiB 2 content, the relative density, hardness, and strength of the composites increase greatly, but the plasticity decreases gradually.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced materials and composites · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (44)

Show source-provided references
1. Application of modern aluminum alloys to aircraft10.1016/0376-0421(95)00004-6 ↗
2. Recent developments in advanced aircraft aluminium alloys10.1016/j.matdes.2013.12.002 ↗
3. Recent advances in the development of aerospace materials10.1016/j.paerosci.2018.01.001 ↗
4. Temperature and wear analysis in milling of aerospace grade aluminum alloy Al-705010.1007/s11740-015-0623-x ↗
5. Effect of hot pressing temperature on microstructure and mechanical properties of SiC particle reinforced aluminum matrix composites
6. Mechanical and thermal expansion behavior of hipped aluminum–TiB2 composites10.1016/j.matchemphys.2005.07.075 ↗
7. Reinforcement behavior in laser welding of A356/TiB2p MMCs10.2320/matertrans.M2011385 ↗
8. Processing and properties of monolithic TiB2 based materials10.1179/174328006X102529 ↗
9. Evaluation of residual stress distribution and relaxation on in situ TiB(2)/7050 Al composites10.3390/ma11050706 ↗
10. High cycle fatigue behavior of the in-situ TiB2/7050 composite10.1016/j.msea.2015.06.023 ↗
11. Fabrication and analysis of TIG welding-brazing butt joints of in-situ TiB2/7050 composite and TA210.1016/j.dt.2020.06.022 ↗
12. Development of Al 6063–TiB2 in situ composites10.1016/j.matdes.2009.10.019 ↗
13. Formation of TiB2 particles during dissolution of TiAl3 in Al–TiB2 metal matrix composite using an in situ technique10.1016/j.compscitech.2005.04.016 ↗
14. Effect of TiB2 particles on sliding wear behaviour of Al–4Cu alloy10.1016/j.wear.2006.04.003 ↗
15. Microstructures and mechanical properties of an Al-Cu-Mg-Sc alloy reinforced with in-situ TiB2 particulates10.1016/j.msea.2020.139603 ↗
16. Commercial processing of metal matrix composites10.1016/S0921-5093(97)00828-9 ↗
17. Influence of hot pressing sintering temperature and time on microstructure and mechanical properties of TiB2 ceramics10.1016/S0955-2219(01)00424-1 ↗
18. Effects of sintering and extrusion on the microstructures and mechanical properties of a SiC/Al-Cu composite10.1007/s11665-011-9940-1 ↗
19. The effect of production parameters on microstructure and wear resistance of powder metallurgy Al–Al2O3 composite10.1016/j.matdes.2010.07.016 ↗
20. Study of microstructure of SiCp/ZL101A composites by vacuum hot-pressing sintering processing
21. Effects of die-pressing pressure and extrusion on the microstructures and mechanical properties of SiC reinforced pure aluminum composites10.1016/j.matdes.2009.08.011 ↗
22. An electron microscope investigation of the microstructure in an aluminium-zinc-magnesum alloy10.1016/0001-6160(70)90016-7 ↗
23. Evolution of eutectic structures in Al-Zn-Mg-Cu alloys during heat treatment10.1016/S1003-6326(06)60101-5 ↗
24. Powder metallurgy processing of 2xxx and 7xxx series aluminium alloys10.1179/1879139511Y.0000000003 ↗
25. Effects of sintering atmosphere on the mechanical properties of Al-Fe particle-reinforced Al-based composites10.1007/s11665-015-1470-9 ↗
26. Tensile properties of laminated composites based on ultrahigh carbon steel10.1177/002199839102500704 ↗
27. C. Butler, A primer on the Taguchi method: by Ranjit Roy, Published by Van Nostrand Rheinhold, USA, 1990, Comput. Integr. Manuf. Syst., 1992, p. 247. 〈https://doi.org/10.1016/0951-5240(92)90037-D〉.10.1016/0951-5240(92)90037-D ↗
28. An optimization method for multi-objective and multi-factor designing of a ceramic slurry: combining orthogonal experimental design with artificial neural networks10.1016/j.ceramint.2018.06.010 ↗
29. Optimisation of the spark plasma sintering process for high volume fraction SiCp/Al composites by orthogonal experimental design10.1016/j.ceramint.2020.09.240 ↗
30. L. Ren, Test Design and Optimization, Science, Beijing, 2009, pp. 71–77.
31. An improved process for grain refinement of large 2219 Al alloy rings and its influence on mechanical properties10.1016/j.jmst.2018.09.007 ↗
32. Effects of forming temperature on properties of SiCP /Al composite
33. Solid state sintering and consolidation of Al powders and Al matrix composites10.1016/S1471-5317(03)00004-X ↗
34. The crystallinity and hardness properties of Al-Cu/SiCp new composite materials10.4028/www.scientific.net/AMR.576.450 ↗
35. Phase transformations in metals and alloys10.1007/978-1-4899-3051-4 ↗
36. The effect of particle size, sintering temperature and sintering time on the properties of Al–Al2O3 composites, made by powder metallurgy10.1016/j.jmatprotec.2009.04.007 ↗
37. Microstructural characterization and tensile properties of hot pressed Al–SiC composites prepared from pure Al and Cu powders10.1016/S0921-5093(00)01656-7 ↗
38. Effect of hot pressing temperature on microstructure and tensile properties of SiC/Al-Zn-Mg-Cu composites
39. Liquid phase sintering of an AA2014-based composite prepared from an elemental powder mixture10.1023/A:1004594628862 ↗
40. Strengthening mechanisms in particulate metal matrix comosites10.1016/0956-716X(91)90349-6 ↗
41. Spark plasma sintering and characterization of Al-TiB2 composites10.3390/met10091110 ↗
42. High-temperature wetting and interfacial interaction between liquid Al and TiB2 ceramic10.1007/s10853-015-8814-6 ↗
43. George E. Dieter, Mechanical metallurgy-1976, second ed., 1961.10.5962/bhl.title.35895 ↗
44. Microstructure and mechanical properties of in-situ TiB2/Al composites