journal article·2025-01

Aluminum matrix composites reinforced with high-entropy oxides and in situ formed Al2O3 and intermetallic compounds through aluminothermic reactions during spark plasma sintering

Umedjon U. Narzulloev, Danil V. Barilyuk, Ksenia A. Kokina, Mariya N. Fatykhova, Pavel A. Loginov, Artem A. Korol, Anton S. Konopatsky, Andrei T. Matveev, Dmitry V. Shtansky

Publisher page

Abstract

This work proposes a new strategy for producing aluminum matrix composites with strong interfaces by forming additional reinforcing particles in situ through an aluminothermic reaction between the system components. Sol-gel synthesized high-entropy spinel-type (Cr 0.23Mn 0.22Fe 0.22Co 0.19Ni 0.13) 3O 4 oxides (HEO) were added to Al nanopowder and the resulting mixture was subjected to high-energy ball milling (HEBM) and then spark plasma sintering (SPS). As a result of the aluminothermic reaction during SPS, HEO are partially reduced, providing excess oxygen for the formation of reinforcing Al 2O 3 nanoparticles, and the reduced metals react with Al with the formation of various intermetallic compounds (Al 9Me 2, Al 5Me 2, and Al 2Me), which, in addition to HEO, serve as secondary strengthening phases. A new hexagonal AlMe x phase with lattice parameters of approximately a = c = 1.76 nm has been well documented. HEBM has been shown to be an important step not only for uniform HEO distribution, but also for the aluminothermic reaction to occur at a relatively low temperature by improving the interaction between activated Al and HEO nanopowders. The maximum increase in hardness with the addition of HEO is 198 %, tensile strength 90 % (25°C) and 97 % (500°C), and compressive strength 220 % (25°C) and 250 % (500°C). Excellent mechanical properties are achieved at 500°C: the ultimate tensile and compressive strength are 258 MPa and 410 MPa, respectively. The introduction of HEO also leads to a significant reduction in the coefficient of friction (from 0.7 (0 %) to 0.2 (3 %HEO)) and a noticeable reduction in dynamic wear (5.9–6.3 (3 %HEO) and 10.6–14.3 (5 %HEO) times depending on applied load). Thus, our research opens up exciting new possibilities for creating lightweight and high strength composites for use in the mid-temperature range.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Entropy Alloys Studies · Advanced ceramic materials synthesis · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (48)

Show source-provided references
1. Aluminum metal–matrix composites for automotive applications: tribological considerations10.1023/B:TRIL.0000044492.91991.f3 ↗
2. Advances in hybrid aluminium metal matrix composite produced by stir casting route: a review on applications and fabrication characteristics
3. Dry sliding wear of aluminum composites: a review10.1016/S0266-3538(96)00167-4 ↗
4. Small punch testing of heat resistant ultrafine-grained Al composites stabilized by nano-metric Al2O3 (HITEMAL©) in a broad temperature range10.1016/j.jallcom.2021.161332 ↗
5. Influence of grain boundaries with dispersed nanoscale Al2O3 particles on the strength of Al for a wide range of homologous temperatures10.1016/j.jallcom.2018.09.164 ↗
6. Mechanical properties and corrosion behavior of Al/SiC composites10.1016/j.jallcom.2016.03.180 ↗
7. Fabrication and properties of functionally graded Al/AlB2 composites10.1177/0021998314541490 ↗
8. Influence mechanisms of Cu or Fe on the microstructures and tensile properties at 350 °C of network AlNp reinforced Al composites10.1016/j.jallcom.2017.12.125 ↗
9. Improved dispersion of carbon nanotubes in aluminum nanocomposites10.1016/j.compstruct.2013.10.043 ↗
10. Fabrication, characterization, and mechanical properties of spark plasma sintered Al–BN nanoparticle composites10.1016/j.msea.2015.06.059 ↗
11. Wear and corrosion behavior of high entropy alloys
12. Aluminium matrix composites reinforced with high entropy alloys: a comprehensive review on interfacial reactions, mechanical, corrosion, and tribological characteristics10.1016/j.jmrt.2024.05.153 ↗
13. Interface characteristics and mechanical properties of Al0.6CoCrFeNi/5052Al matrix composites fabricated via vacuum hot-pressing sintering and annealing10.1016/j.msea.2022.144234 ↗
14. Al/SiC composites with enhanced thermomechanical properties obtained from microwave plasma-treated nanopowders10.1016/j.msea.2021.141817 ↗
15. Microwave plasma-produced Al/Al2O3 microparticles as precursors for high-temperature high-strength composites10.1016/j.jallcom.2023.172879 ↗
16. Structural synergy of nanoAl2O3/nanoAl composites with high thermomechanical properties and ductility10.3390/met13101696 ↗
17. Al-based composites reinforced with ceramic particles formed by in situ reactions between Al and amorphous SiNxOy10.1016/j.msea.2022.143105 ↗
18. High-entropy alloy Al0.2Co1.5CrFeNi1.5Ti0.5 prepared from high-entropy oxide (Al0.2Co1.5CrFeNi1.5Ti0.5)3O4 by a deoxidation process via a CaH2-assisted molten salt method10.3390/met14040443 ↗
19. Two-step hydrogen reduction of oxides for making FeCoNiCu high entropy alloy: Part I – Process and mechanical properties10.1016/j.matchar.2022.112271 ↗
20. Possibility of obtaining refractory high-entropy AlTiZrVNb alloys from metal oxides10.1007/s11172-023-3852-7 ↗
21. Entropy-stabilized oxides10.1038/ncomms9485 ↗
22. Synthesis and microstructure of the (Co,Cr,Fe,Mn,Ni)3O4 high entropy oxide characterized by spinel structure10.1016/j.matlet.2017.12.148 ↗
23. Spinel-structured high entropy oxide (FeCoNiCrMn)3O4 as anode towards superior lithium storage performance10.1016/j.jallcom.2020.156158 ↗
24. Facile synthesis of nanosized spinel high entropy oxide (FeCoNiCrMn)3O4 for efficient oxygen evolution reaction
25. Charge-induced disorder controls the thermal conductivity of entropy-stabilized oxides10.1002/adma.201805004 ↗
26. High-entropy ceramics: present status, challenges, and a look forward10.1007/s40145-021-0477-y ↗
27. Tailoring high-entropy oxides to ameliorate interfacial mismatch of aluminum-matrix composites towards superior strength-ductility balance10.1016/j.msea.2024.146813 ↗
28. The solid-state combustion synthesis of in-situ hybrid (Al3Ni+Al2O3)/Al composites and evaluation of its mechanical properties10.1016/j.jallcom.2022.167917 ↗
29. Reactive mechanism and mechanical properties of in-situ hybrid nano-composites fabricated from an Al–Fe2O3 system by friction stir processing10.1016/j.matchar.2017.03.007 ↗
30. Formation of Al/(Al13Fe4 + Al2O3) nano-composites via mechanical alloying and friction stir processing10.1007/s11665-018-3170-8 ↗
31. Mechanism of zinc oxide–aluminum aluminothermic reaction10.1007/s10853-010-4619-9 ↗
32. Elastic strain measurements of miniature tensile specimens10.1007/s11340-013-9785-7 ↗
33. Uncertainty in the determination of elastic modulus by tensile testing
34. Oxidation of Cr(III) to Cr(VI) species during the thermal decomposition process of Zn/Cr-layered double hydroxide carbonate10.1246/cl.1993.1479 ↗
35. Unveiling the potential of (CoFeNiMnCr)3O4 high-entropy oxide synthesized from CoFeNiMnCr high-entropy alloy for efficient oxygen-evolution reaction10.1007/s10853-024-09710-5 ↗
36. Precipitation of iron-rich intermetallic phases in Al-4.6Cu-0.5Fe-0.5Mn cast alloy10.1007/s10853-012-6279-4 ↗
37. Enhancing High-temperature strength and thermal stability of Al2O3/Al composites by high-temperature pre-treatment of ultrafine Al powders10.1007/s40195-020-01038-8 ↗
38. High strength and high creep resistant ZrB2/Al nanocomposites fabricated by ultrasonic-chemical in-situ reaction10.1016/j.jmst.2019.04.020 ↗
39. High-temperature mechanical properties and fracture mechanisms of Al–Si piston alloy reinforced with in situ TiB2 particles10.1016/j.msea.2015.03.021 ↗
40. Synthesis of a (ZrAl3+AlN)/Al composite and the influence of particles content and element Cu on the microstructure and mechanical properties10.1016/j.jallcom.2019.03.416 ↗
41. Experimental comparison of the effects of nanometric and micrometric particulates on the tensile properties and fracture behavior of Al composites at room and elevated temperatures10.1007/s11661-010-0505-y ↗
42. Effect of SiC addition in fabrication of Al/SiC metal matrix composite by stir casting
43. Experimental investigations on mechanical properties of Al-B4C metal matrix composites
44. Industrially fabricated in-situ Al-AlN metal matrix composites (part B): The mechanical, creep, and thermal properties10.1016/j.jallcom.2022.164720 ↗
45. Nanopowder derived Al/h-BN composites with high strength and ductility10.1016/j.jallcom.2022.165199 ↗
46. Elevated-temperature high-strength h-BN-doped Al2014 and Al7075 composites: experimental and theoretical insights10.1016/j.msea.2021.140969 ↗
47. Review of recent trends and developments in aluminium 7075 alloy and its metal matrix composites (MMCs) for aircraft applications10.1016/j.rineng.2023.101372 ↗
48. Review: recent progress in aluminum matrix composites reinforced by in situ oxide ceramics10.1007/s10853-023-09120-z ↗