Optimizing the mechanical and corrosion properties of an ultrafine-grained Al-Cu-Mg alloy through cyclic deformation: Clusters and lattice defects
Source abstract
Abstract
To optimize its corrosion and mechanical properties, an Al-Cu-Mg alloy is cyclically processed by high-pressure torsion (HPT), involving a 1/2 turn clockwise and a 1/2 turn counter-clockwise per cycle. The dislocation density increases to 3.04×10 14 m −2 on 1 cycle HPT and decreases gradually to 2.23×10 14 m −2 for higher cyclic rotations (i.e. 5 cycle HPT). Due to the rapid elimination of the geometrically necessary dislocations, the refinement of grain size in cyclic HPT is more efficient than the monotonic HPT (i.e. it decreases from 2.48 μm to 112 nm on 1 cycle HPT). The HPT samples are electrochemically corroded in a simulated seawater environment. 1-cycle HPT process causes a strong increase in hardness (to 232 HV) and an increase in corrosion potential (to −0.517 V). The trade-off between hardness/strength and corrosion resistance is broken on cyclic HPT processing. Aided by excess vacancies induced by HPT, Cu-Mg clusters form on and near grain boundaries through a ‘vacancy-pump’ mechanism, causing solute depleted zones (SDZ) adjacent to GBs. The combined effects of ultrafine grains, solute cluster segregation and SDZs enhance the strength and corrosion resistance of the Al-Cu-Mg alloys. This study provides a potential strategy to design the microstructures of an Al alloy, and to achieve a higher hardness and a better corrosion performance of that material.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (65)
Show source-provided references
1. Enhanced strength-plasticity combination in an Al–Cu–Mg alloy—atomic scale microstructure regulation and strengthening mechanisms10.1016/j.msea.2020.139447 ↗
2. The optimum grain size for strength-ductility combination in metals10.1016/j.ijplas.2023.103574 ↗
3. New insights on the initial local corrosion of composite Al7Cu2Fe/Al20Cu2Mn3 intermetallic particles in 2024-T351 aluminum alloy10.1016/j.corsci.2022.110657 ↗
4. Aluminium AA2024 T351 aeronautical alloy: Part 1. Microbial influenced corrosion analysis10.1016/j.msea.2007.06.079 ↗
5. Influence of hydrogen on the propagation of intergranular corrosion defects in 2024 aluminium alloy10.1016/j.corsci.2018.12.019 ↗
6. Using high-pressure torsion for metal processing: fundamentals and applications10.1016/j.pmatsci.2008.03.002 ↗
7. Analytical and numerical approaches to modelling severe plastic deformation10.1016/j.pmatsci.2018.02.001 ↗
8. Nanomaterials by severe plastic deformation: review of historical developments and recent advances10.1080/21663831.2022.2029779 ↗
9. Severe plastic deformation for producing superfunctional ultrafine-grained and heterostructured materials: an interdisciplinary review10.1016/j.jallcom.2024.174667 ↗
10. Strengthening of an Al–Cu–Mg alloy processed by high-pressure torsion due to clusters, defects and defect–cluster complexes10.1016/j.msea.2014.12.107 ↗
11. Microstructural evolution, strengthening and thermal stability of an ultrafine-grained Al–Cu–Mg alloy10.1016/j.actamat.2016.02.050 ↗
12. Dynamic precipitation, segregation and strengthening of an Al-Zn-Mg-Cu alloy (AA7075) processed by high-pressure torsion10.1016/j.actamat.2018.09.060 ↗
13. Temperature-dependent-composition of η phase in an Al-Zn-Mg-Cu alloy under high pressure torsion: kinetics and thermodynamics10.1016/j.actamat.2022.118181 ↗
14. Achieving ultra-high strength of Al-Cu-Li alloys by the combination of high pressure torsion and age-hardening10.1016/j.msea.2021.142504 ↗
15. The nanoscale mechanisms of strengthening and ductility enhancement in an Al–Mg–Si–Mn alloy on processing by high-pressure torsion10.1016/j.matchar.2023.113145 ↗
16. An investigation of hardness homogeneity throughout disks processed by high-pressure torsion10.1016/j.actamat.2010.09.034 ↗
17. Making strong nanomaterials ductile with gradients10.1126/science.1255940 ↗
18. Mechanical properties and deformation mechanisms of gradient nanostructured metals and alloys10.1038/s41578-020-0212-2 ↗
19. Towards understanding the structure–property relationships of heterogeneous-structured materials10.1016/j.scriptamat.2020.05.013 ↗
20. Geometrically necessary dislocations and related kinematic hardening in gradient grained materials: a nonlocal crystal plasticity study10.1016/j.ijplas.2023.103553 ↗
21. Al-Mg-Cu based alloys and pure Al processed by high pressure torsion: the influence of alloying additions on strengthening10.1016/j.msea.2010.02.016 ↗
22. Influence of strain reversals during high pressure torsion process on strengthening in Al-Cu-Mg(-Li) alloy10.4028/www.scientific.net/MSF.667-669.809 ↗
23. Effects of solution treatment on the microstructure and mechanical properties of naturally aged EN AW 2024 Al alloy sheet10.1016/j.jallcom.2020.153943 ↗
24. Localized corrosion behavior associated with Al7Cu2Fe intermetallic in Al-Zn-Mg-Cu-Zr alloy10.1016/j.jallcom.2018.12.151 ↗
25. Electrochemical assessment of interfacial characteristics of intermetallic phases present in aluminium alloy 2024-T310.1016/j.corsci.2015.09.012 ↗
26. Regulating solute partitioning utilized to decorate grain boundary for improving corrosion resistance in a model Al-Cu-Mg alloy10.1016/j.corsci.2020.109219 ↗
27. Effect of retrogression treatment with different heating rates on microstructure, strength and corrosion behaviors of 7050 alloy10.1016/j.matchar.2022.111819 ↗
28. Synchronous improvement of mechanical properties and stress corrosion resistance by stress-aging coupled with natural aging pre-treatment in an Al-Zn-Mg alloy with high recrystallization fraction10.1016/j.jmst.2021.11.068 ↗
29. Microhardness and corrosion properties of hypoeutectic Al–7Si alloy processed by high-pressure torsion10.1016/j.matdes.2015.06.018 ↗
30. Corrosion behavior of Al–3Mg–0.2Sc alloy processed by high-pressure torsion and thermal treated10.1016/j.jmrt.2022.03.054 ↗
31. Modelling precipitation kinetics: evaluation of the thermodynamics of nucleation and growth10.1016/j.calphad.2015.04.013 ↗
32. Grain refinement and high strain rate superplasticity in alumunium 2024 alloy processed by high-pressure torsion10.1016/j.msea.2014.11.009 ↗
33. The significance of slippage in processing by high-pressure torsion10.1016/j.scriptamat.2008.08.042 ↗
34. Some unresolved problems of high-pressure torsion10.2320/matertrans.MT-MF2022038 ↗
35. Microstructures and hardness prediction of an ultrafine-grained Al-2024 alloy10.3390/met9111182 ↗
36. Mechanical properties of nanocrystalline materials10.1016/j.pmatsci.2005.08.003 ↗
37. The thermodynamics of and strengthening due to co-clusters: general theory and application to the case of Al-Cu-Mg alloys10.1016/j.actamat.2009.01.021 ↗
38. Atomic-scale analysis of the segregation and precipitation mechanisms in a severely deformed Al–Mg alloy10.1016/j.actamat.2014.03.033 ↗
39. High-pressure torsion for enhanced atomic diffusion and promoting solid-state reactions in the aluminum–copper system10.1016/j.actamat.2013.02.042 ↗
40. Deformation induced grain boundary segregation in nanolaminated Al–Cu alloy10.1016/j.actamat.2019.10.036 ↗
41. Dislocation versus grain boundary strengthening in SPD processed metals: non-causal relation between grain size and strength of deformed polycrystals10.1016/j.msea.2017.08.069 ↗
42. Hardening of pure metals by high-pressure torsion: a physically based model employing volume-averaged defect evolutions10.1016/j.actamat.2012.09.048 ↗
43. Thermal conductivity of Al–Cu–Mg–Si alloys: experimental measurement and CALPHAD modeling10.1016/j.tca.2016.04.019 ↗
44. Understanding formation of Mg-depletion zones in Al-Mg alloys under high pressure torsion10.1016/j.jmst.2018.11.017 ↗
45. Effect of Mg on microstructure and mechanical properties of Al-Mg alloys produced by high pressure torsion10.1016/j.scriptamat.2018.09.033 ↗
46. Developing age-hardenable Al-Zr alloy by ultra-severe plastic deformation: significance of supersaturation, segregation and precipitation on hardening and electrical conductivity10.1016/j.actamat.2020.116503 ↗
47. Equilibrium vacancies and thermophysical properties of metals10.1016/S0370-1573(97)00082-3 ↗
48. Diffusion coefficients of some solutes in fcc and liquid Al: critical evaluation and correlation10.1016/S0921-5093(03)00624-5 ↗
49. The presence and nature of vacancy type defects in nanometals detained by severe plastic deformation10.1016/j.msea.2007.06.093 ↗
50. Significance of temperature increase in processing by high-pressure torsion10.1016/j.msea.2011.06.031 ↗
51. Grain boundary segregation and intermetallic precipitation in coarsening resistant nanocrystalline aluminum alloys10.1016/j.actamat.2018.09.038 ↗
52. Correlation between microstructural evolution and corrosion resistance of hypoeutectic Al–Si–Mg alloy: influence of corrosion product layer10.1016/j.matchar.2022.112276 ↗
53. Effects of Mg contents on microstructures and corrosion behaviors of homogenization Al-Zn-Mg-Cu alloys10.1016/j.corsci.2023.111461 ↗
54. Local corrosion mechanism of an Al-Zn-Mg-Cu alloy in oxygenated chloride solution: cathode activity of quenching-induced η precipitates10.1016/j.corsci.2021.109743 ↗
55. Modifying the microstructure and stress distribution of crossover Al-Mg-Zn alloy for regulating stress corrosion cracking via retrogression and re-aging treatment10.1016/j.msea.2023.145564 ↗
56. Dealloying-driven local corrosion by intermetallic constituent particles and dispersoids in aerospace aluminium alloys10.1016/j.corsci.2020.108947 ↗
57. Simultaneous enhancement in mechanical and corrosion properties of Al-Mg-Si alloys using machine learning10.1016/j.jmst.2023.04.072 ↗
58. Effect of Zr content on corrosion behavior and chemically-milled surface roughness of Al-Cu-Mg alloy10.1016/j.jallcom.2023.171364 ↗
59. In-situ nanoscopic observations of dealloying-driven local corrosion from surface initiation to in-depth propagation10.1016/j.corsci.2020.108912 ↗
60. Corrosion of AA2024-T3 Part II: co-operative corrosion10.1016/j.corsci.2010.09.030 ↗
61. Corrosion of AA2024-T3 Part III: propagation10.1016/j.corsci.2010.09.035 ↗
62. Effect of grain size on corrosion: a review10.5006/1.3462912 ↗
63. Corrosion of ultrafine grained materials by severe plastic deformation, an overview10.2320/matertrans.M2015452 ↗
64. The effect of grain size and strain on the tensile flow stress of aluminium at room temperature10.1016/0001-6160(77)90171-7 ↗
65. Six decades of the Hall–Petch effect – a survey of grain-size strengthening studies on pure metals10.1080/09506608.2016.1191808 ↗