journal article·2024-11

Effects of trace nano-TiB2 particles and multiple cooling rates on microstructure and properties of Al-4.5Cu alloy

Yuewu Zheng, Hong Xu, Xiang Kong, Yu Wang, Xiaofeng Li, Yu Bai, Hongkui Mao

Publisher page

Abstract

Ceramic particles and cooling rates have important effect on the Strength and plasticity of aluminum-based materials. In this paper, the microstructure and mechanical properties of Al-4.5Cu alloy were controlled by adding ultra-trace amounts of in-situ synthesized TiB 2 particles and multiple cooling rates. The results show, that the average size of TiB 2 particles is about 86.35 nm. The lattice dis-registry between TiB 2 and α-Al was calculated to be 4.5 %, the TiB 2 particles can be used as α-Al heterogeneous nucleation cores. The average grain size and standard deviation of Al-4.5Cu alloy with the addition of 0.02 wt% TiB 2 and high cooling rate are 30.5 μm and 15.9, respectively. Compared with the Al-4.5Cu alloy without adding TiB 2 particles and at medium cooling rate, the average grain size and standard deviation decreased by 68.1 % and 44.2 %, respectively. It can be seen from the room temperature tensile properties of the alloy after T6 heat treatment, that the yield strength, tensile strength and elongation of the Al-4.5Cu alloys with the addition of 0.02 wt% TiB 2 and high cooling rate are 468.3 MPa, 513.9 MPa, and 13.4 %, respectively. Compared with the Al-4.5Cu alloy without adding ceramic particles and at medium cooling rate, the yield strength, tensile strength and elongation increased by 15.6 %, 9.2 % and 25.2 %, respectively.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. The growth behavior and kinetics of intermetallic compounds in Cu–Al interface at 600°C–800 °C10.1016/j.intermet.2024.108244 ↗
2. Anomalous two-step repair mechanism of Al–Cu alloy regulated by the surroundings during E-beam irradiation10.1016/j.jmrt.2024.01.011 ↗
3. Enhancement of mechanical properties of Al-Cu alloy composite reinforced by Ni element: A combination of mixture design of experiment and artificial neural network approach
4. Stress-induced symmetrical tilt boundaries in layer-structured Al-Cu eutectic alloys10.1016/j.scriptamat.2024.116025 ↗
5. The nucleation sequence of α-Al on TiB2 particles in Al-Cu alloys10.1016/j.actamat.2021.116652 ↗
6. Low-temperature CO preferential oxidation in H2-rich stream over Indium modified Pd-Cu/Al2O3 catalyst10.1016/j.jcis.2024.02.003 ↗
7. Microstructure evolution and strengthening mechanisms of a high-performance TiN-reinforced Al–Mn–Mg–Sc–Zr alloy processed by laser powder bed fusion10.1016/j.jmst.2023.11.033 ↗
8. Microstructure evolution and mechanical properties strengthening in laser powder bed fusion of high-strength SiC and TiB2 co-reinforced Al-Zn-Mg-Cu composites10.1016/j.jallcom.2023.171463 ↗
9. Interfacial strain evolution and abnormal Poisson's ratios in Al nuclei for the Al/TiB2 heterostructure10.1016/j.scriptamat.2023.115508 ↗
10. Interfacial precipitation of the in-situ TiB2-reinforced Al–Zn–Mg–Cu–Zr composite10.1016/j.matchemphys.2023.127561 ↗
11. Low-temperature synthesis and sinterability of high-purity submicron TiB2 powder via microwave-assisted carbothermal reduction10.1016/j.jeurceramsoc.2024.01.054 ↗
12. Achieving strength-ductility balance in a laser powder bed fusion fabricated TiB2/Al–Cu-Mg-Ag alloy10.1016/j.jallcom.2023.169311 ↗
13. On the preparation and mechanical properties of in situ small-sized TiB2/Al-4.5Cu composites via ultrasound assisted RD method10.1016/j.jallcom.2018.06.303 ↗
14. Effect of laser additive manufacturing on the microstructure and mechanical properties of TiB2 reinforced Al-Cu matrix composite10.1016/j.msea.2022.142950 ↗
15. Enhancing mechanical properties of uniformly distributed nano TiB2/2024 Al composite rolling sheet by pre-stretch aging10.1016/j.jallcom.2022.165172 ↗
16. Selective laser melting of nano-TiB2 decorated AlSi10Mg alloy with high fracture strength and ductility10.1016/j.actamat.2017.02.062 ↗
17. Processing, multiscale microstructure refinement and mechanical property enhancement of hypoeutectic Al–Si alloys via in situ bimodal-sized TiB2 particles10.1016/j.msea.2020.139081 ↗
18. Microstructure evolution and properties improvement of in-situ TiB2/6061 composites via trace Mn addition10.1016/j.molstruc.2023.137423 ↗
19. Synergistic optimization in solidification microstructure and mechanical performance of novel (TiC N − TiB2)p/Al nanocomposites: Design, tuning and mechanism10.1016/j.compositesa.2022.106843 ↗
20. Enhanced combination of strength and ductility in the semi-solid rheocast hypereutectic Al Si alloy with the effect of in-situ TiB2 particles10.1016/j.matchar.2021.111143 ↗
21. The effect of carbide and nitride additions on the heterogeneous nucleation behavior of liquid iron10.1007/BF03037838 ↗
22. Manufacturing of (Al–10Zn) / TiB2 in-situ nanocomposites by reactive liquid metallurgy and hot-extrusion for enhanced interfacial bonding and mechanical properties10.1016/j.msea.2022.144200 ↗
23. Integrated model for describing the microstructure evolution of the inoculated Al-Zn-Mg-Cu alloys in continuous solidification10.1016/j.rinp.2021.104465 ↗
24. Correlation between tensile properties, microstructure, and processing routes of an Al–Cu–Mg–Ag–TiB2 (A205) alloy: additive manufacturing and casting10.1016/j.msea.2022.142989 ↗
25. Enhancing strength-ductility synergy and mechanisms of Al-based composites by size-tunable in-situ TiB2 particles with specific spatial distribution10.1016/j.compositesb.2021.108912 ↗
26. Effect of high cooling rate on the solidification microstructure of Al–Cu/TiB2 alloy fabricated by freeze-ablation casting10.1016/j.jmrt.2023.05.215 ↗
27. Effects of cooling rates on the solidification behavior, microstructural evolution and mechanical properties of Al–Zn–Mg–Cu alloys10.1016/j.jmrt.2022.12.082 ↗
28. Effects of nano-TiCp on the microstructures and tensile properties of TiCp/Al–Cu composites10.1016/j.matchar.2014.05.012 ↗
29. Investigation on work hardening rate of Al-Zn-Mg-Cu alloy under solid solution process and thermomechanical coupled multi-step fast aging process10.1016/j.jallcom.2024.174892 ↗
30. Effect of Mg on the microstructure evolution and mechanical properties of 5%TiB2/Al−4.5%Cu composites
31. Effects of cooling rate and TiC nanoparticles on the microstructure and tensile properties of an Al–Cu cast alloy10.1016/j.msea.2020.139737 ↗
32. Effects of nanoparticles on the solution treatment and mechanical properties of nano-SiCp/Al-Cu composites10.1016/j.jmatprotec.2021.117195 ↗
33. Enhanced age-hardening behavior in Al–Cu alloys induced by in-situ synthesized TiC nanoparticles10.1016/j.jmst.2018.09.029 ↗
34. Improving the strength-ductility trade-off of TiB2/Al-4.5%Cu composites via Mg–Ag microalloying and multi-step heat treatment10.1088/2053-1591/ac0264 ↗
35. The nano-sized TiC particle reinforced Al–Cu matrix composite with superior tensile ductility10.1016/j.msea.2014.11.006 ↗
36. Controlling the sizes of in-situ TiC nanoparticles for high-performance TiC/Al–Cu nanocomposites10.1016/j.ceramint.2021.07.017 ↗
37. In-situ investigation on the microstructure evolution and plasticity of two magnesium alloys during three-point bending10.1016/j.ijplas.2015.05.010 ↗
38. Annealing behavior of a cast Mg-Gd-Y-Zr alloy with necklace fine grains developed under hot deformation10.1016/j.msea.2017.02.008 ↗
39. Role of {10–12} twinning characteristics in the deformation behavior of a polycrystalline magnesium alloy10.1016/j.actamat.2010.07.002 ↗
40. Basal slip mediated tension twin variant selection in magnesium WE43 alloy10.1016/j.actamat.2019.03.018 ↗
41. Grain fragmentation associated continuous dynamic recrystallization (CDRX) of hexagonal structure during uniaxial isothermal compression: High-temperature α phase in TiAl alloys10.1016/j.intermet.2020.107028 ↗
42. Acquiring Mg-Ag microalloying TiB2/Al-4.5Cu composite simultaneously with ultrahigh strength and ductility via optimized salt-metal reaction and multistage heat treatment10.1016/j.matdes.2022.111252 ↗