journal article·2024-10

Enhancing microstructural control and performance of 5A06 alloy through liquid CO2-assisted friction stir processing

Yingxin Geng, Mengran Zhou, Yixing Zhu, Xiaoyu Zhou, Hongwei Li, Yujie Chen, Gaoqiang Chen, Ruizhi Wu, Qingyu Shi

Publisher page

Abstract

Next-generation armored vehicles possess external structures embellished with O-tempered 5A06 alloy, exhibiting with strength and lightweight attributes. However, a universally applicable method that can concurrently enhance the mechanical properties and corrosion resistance of O-tempered 5A06 alloy has yet to be developed. This study comparatively analyzed between conventional friction stir processing (FSP) and liquid CO 2 -assisted friction stir processing (LCFSP) on the 5A06 aluminum alloy. The findings revealed that LCFSP stands out as a practical approach, leading to notable refinement and homogeneity in microstructure. After LCFSP at a tool rotation speed of 400 rpm, the coarse grains were replaced by refined equiaxial grains with an average diameter of 6.0±3.3 μm. The increase in the strength of the liquid CO 2 -assisted friction stir-processed samples, compared with conventional FSP, primarily stemmed from grain boundary strengthening, dislocation strengthening, and precipitation strengthening. Furthermore, the fine-grained microstructure played a pivotal role in fostering the formation of an amorphous passive layer on the Al alloy, which contributed to the increase in corrosion resistance. Therefore, LCFSP emerges as an effective method for enhancing the performance of 5A06 alloy in armored vehicles.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (61)

Show source-provided references
1. Microstructure and mechanical properties in friction stir welded 5A06 aluminum alloy thick plate10.1016/j.matdes.2016.10.030 ↗
2. Stress corrosion cracking resistant nanostructured Al-Mg alloy with low angle grain boundaries10.1016/j.actamat.2021.117607 ↗
3. Intergranular Corrosion and Stress Corrosion Cracking of Sensitised AA518210.4028/www.scientific.net/MSF.519-521.641 ↗
4. Effects of alloy modification and thermomechanical processing on recrystallization of Al-Mg-Mn alloys10.1007/BF02663844 ↗
5. Enhanced grain refinement and texture weakening in Al-Mg-Si alloy through a novel thermomechanical processing10.1016/j.jallcom.2022.166654 ↗
6. Fabrication of large-scale steel-aluminum components with homogenously distributed amorphous interfacial layer and enhanced bonding strength using modified friction stir additive manufacturing10.1016/j.jmst.2024.01.036 ↗
7. In-situ rolling friction stir welding of aluminum alloys towards corrosion resistance10.1016/j.corsci.2024.111920 ↗
8. A study on corrosion behavior of friction stir welded and tungsten inert gas welded AA2014 aluminium alloy10.1016/j.corsci.2018.01.012 ↗
9. Microstructure evolution during FSW/FSP of high strength aluminum alloys10.1016/j.msea.2005.06.009 ↗
10. Effect of friction stir processing on the fatigue properties of a Zr-modified 2014 aluminium alloy10.1016/j.matchar.2005.12.015 ↗
11. Characterization of oxide dispersion strengthened copper based materials developed by friction stir processing10.1016/j.matdes.2014.04.012 ↗
12. Relationship between grain size and Zener–Holloman parameter during friction stir processing in AZ31 Mg alloys10.1016/j.scriptamat.2004.05.043 ↗
13. Ultrafine-Grained Al-Mg-Sc Alloy via Friction-Stir Processing10.1007/s11661-012-1461-5 ↗
14. Enhanced corrosion resistance of AZ91 magnesium alloy through refinement and homogenization of surface microstructure by friction stir processing10.1016/j.corsci.2018.04.028 ↗
15. The corrosion behavior of Mg-9Al-xRE magnesium alloys modified by friction stir processing10.1016/j.jallcom.2020.156835 ↗
16. Corrosion resistant and high-strength dual-phase Mg-Li-Al-Zn alloy by friction stir processing10.1038/s43246-022-00245-3 ↗
17. Effect of the processing route on the microstructure and mechanical behavior of superlight Mg-9Li-1Zn alloy via friction stir processing10.1016/j.jma.2021.12.002 ↗
18. Improved corrosion resistance achieved in a friction stir processed Mg-5Zn-0.3Ca alloy with fragmented precipitates10.1016/j.corsci.2022.110675 ↗
19. Achieving synergistic strength-ductility-corrosion optimization in Mg-Li-Al-Zn alloy via cross-pass friction stir processing10.1016/j.jallcom.2023.170581 ↗
20. Simultaneous enhancement of mechanical properties and corrosion resistance of as-cast Mg-5Zn via microstructural modification by friction stir processing10.1016/j.jma.2021.08.029 ↗
21. Effect of friction stir processing conditions on fatigue behavior and texture development in A356-T6 cast aluminum alloy10.1016/j.ijfatigue.2015.06.001 ↗
22. Analysis and Modeling of Friction Stir Processing-Based Crack Repairing in 2024 Aluminum Alloy10.1007/s40195-016-0489-8 ↗
23. Effects of tool rotation speed on the mechanical properties and microstructure of friction stir welded ODS steel10.1016/j.msea.2013.12.022 ↗
24. Mechanical properties of friction stir butt welds of high nitrogen- containing austenitic stainless steel10.1016/j.msea.2010.12.071 ↗
25. Achieving ultra-high strength friction stir welded joints of high nitrogen stainless steel by forced water cooling10.1016/j.jmst.2018.03.014 ↗
26. Deformation behavior of friction-stir welded Al-Mg-Mn alloy with ultrafine-grained structure10.1016/j.matchar.2022.111758 ↗
27. Friction stir welding of AISI 1080 steel using liquid CO2 for enhanced toughness and ductility10.1179/1362171813Y.0000000128 ↗
28. Clarification of microstructure evolution of aluminum during friction stir welding using liquid CO2 rapid cooling10.1016/j.matdes.2017.05.013 ↗
29. Investigation of temperature dependent microstructure evolution of pure iron during friction stir welding using liquid CO2 rapid cooling10.1016/j.matchar.2018.01.004 ↗
30. Multiple effects of forced cooling on joint quality in coolant-assisted friction stir welding10.1016/j.jmrt.2023.06.248 ↗
31. Effects of different cooling conditions on microstructure and precipitation behavior of fine-grained Al-Zn-Mg-Cu alloy friction stir welding joint10.1016/j.jmrt.2023.04.052 ↗
32. Influence of tool material and rotational speed on mechanical properties of friction stir welded AZ31B magnesium alloy10.1016/j.jma.2015.10.001 ↗
33. Microstructure Evolution and Recrystallization Mechanisms of High Mg Alloyed Al-Mg Alloy during Friction Stir Welding with Different Cooling Media10.1007/s11665-022-07349-4 ↗
34. Effect of heat input on microstructure and tensile properties of laser welded Ti-3Al-6Mo-2Fe-2Zr alloy joint10.1016/j.jmrt.2022.01.089 ↗
35. Influence of process parameters on the microstructural evolution and mechanical characterisations of friction stir welded Al-Mg-Si alloy10.1016/j.jmatprotec.2019.116366 ↗
36. Enhanced combination of mechanical properties and electrical conductivity of a hard state Cu-Cr-Zr alloy via one-step friction stir processing10.1016/j.jmatprotec.2020.116880 ↗
37. Grain refining with DDRX by isothermal MDF of Al-Zn-Mg-Cu alloy10.1016/j.jmrt.2020.05.033 ↗
38. Dynamic recrystallization and precipitation behavior of a novel Sc, Zr alloyed Al-Zn-Mg-Cu alloy during hot deformation10.1016/j.matchar.2021.111629 ↗
39. A comparative analysis of a unique DRX process in achieving a homogeneous distribution of β grains in the single phase region of as-cast Ti644321 alloy10.1016/j.matchar.2023.113505 ↗
40. Dislocations and grain size in ball-milled iron powder10.1016/S0965-9773(96)00048-7 ↗
41. The contrast factors of dislocations in cubic crystals: the dislocation model of strain anisotropy in practice10.1107/S0021889899009334 ↗
42. Tool rotational speed impact on temperature variations, mechanical properties and microstructure of friction stir welding of dissimilar high-strength aluminium alloys10.1007/s40430-020-2259-9 ↗
43. Influences of pin profile and rotational speed of the tool on the formation of friction stir processing zone in AA2219 aluminium alloy10.1016/j.msea.2006.12.124 ↗
44. Enhancing friction stir welding efficiency through rotational speed adjustment: a microstructural and mechanical analysis of Al-Cu alloy10.1088/2631-8695/ad1e17 ↗
45. Low temperature superplasticity in a friction-stir-processed ultrafine grained Al-Zn-Mg-Sc alloy10.1016/j.actamat.2005.05.021 ↗
46. Dislocation pipe diffusion10.1016/0001-6160(64)90220-2 ↗
47. Microstructural evolution and its influence on mechanical and corrosion behaviors in a high-Al/Zn containing duplex Mg-Li alloy after friction stir processing10.1016/j.jmst.2023.10.019 ↗
48. Microstructure and mechanical performance of dissimilar friction stir spot welded AA2024-O/AA6061-T6 sheets: Effects of tool rotation speed and pin geometry
49. Al3(Sc,Zr)-based precipitates in Al-Mg alloy: Effect of severe deformation10.1016/j.actamat.2016.10.064 ↗
50. Mechanism of continuous dynamic recrystallization of Ti-6Al-4V alloy during superplastic forming with sub-grain rotation
51. Microstructure evolution and superelastic behavior in Ti-35Nb-2Ta-3Zr alloy processed by friction stir processing10.1016/j.actamat.2017.03.079 ↗
52. Analysis and characterization of dynamic recrystallization and grain structure evolution in friction stir welding of aluminum plates10.1016/j.actamat.2021.116692 ↗
53. D.S. Elswick, Characterization of corrosion pit initiation in aluminum using advanced electron microscopy techniques, 2006, Raleigh, North Carolina.
54. Corrosion of aluminum and aluminum alloys
55. A Compilation of Corrosion Potentials Reported for Intermetallic Phases in Aluminum Alloys10.1149/1.2048447 ↗
56. Enhanced plasticity and corrosion resistance of high strength Al-Zn-Mg-Cu alloy processed by an improved thermomechanical processing10.1016/j.jallcom.2017.05.047 ↗
57. Investigation of aluminum-based nanocomposites with ultra-high strength10.1016/j.msea.2009.07.067 ↗
58. Mechanical behavior of materials10.1016/S1369-7021(09)70086-0 ↗
59. Quasi-in-situ EBSD Study on the Influence of Precipitations on the Strength, Plasticity and Deformation Mechanism in Al-Cu-Li Alloys
60. A review on reinforced particles used on the production of FSP composites10.1016/j.matpr.2021.12.210 ↗
61. Refurbishing damaged surfaces of nickel-aluminum bronze propellers: A robotic approach using gas metal arc welding and friction stir processing10.1063/5.0053484 ↗