Novel applications of ferroalloys for manufacturing of ultra-clean CoCrFeMnNi high-entropy alloy by slagging method
Source abstract
Abstract
The present study provides a benchmark of a sustainable solution utilizing ferroalloys to prepare ultra-clean CoCrFeMnNi high-entropy alloy (HEA). The designed CaO-MgO-Al 2O 3 slags saturated with CaAl 2O 4-MgAl 2O 4 (CA-MA, Slag A) and CaO-MgO (C-M, Slag M) were used to refine the HEA in Al 2O 3 and MgO refractory in an induction furnace under high-purity Ar atmosphere at 1773 K. The characteristics of non-metallic inclusions in the sampled HEA at different time intervals were quantitatively investigated. The results showed that three types of inclusions, i.e., sulfide (MnS), oxide, and complex type (oxide+sulfide), were found in the HEA regardless of refractory and slag types. The oxide inclusions such as MnAl 2O 4 and MgAl 2O 4 spinel particles can exist stably in the HEA melted in Al 2O 3 and MgO refractories with slag A and slag M, respectively. This fact is also confirmed not only by the electrolytic extraction method with elimination of the alloy matrix affection but also by the thermodynamic stability diagram for the HEA. For the structure of the complex inclusions, the core of oxide inclusions usually can act as the subsequent nucleation site for MnS since the precipitation temperature of the oxide inclusions (above the liquidus temperature of the HEA, T L ≅ 1623 K) is higher than that of MnS (below the solidus temperature of the HEA, T S ≅ 1573 K). The HEA melted in the MgO refractory with slag M had a higher cleanliness compared with that melted in the Al 2O 3 refractory with slag A, indicating that the MgO refractory with C-M saturated CaO-MgO-Al 2O 3 slag is suitable for producing an ultra-clean CoCrFeMnNi HEA prepared by the ferroalloys feedstock as the raw materials.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Entropy Alloys Studies · High-Temperature Coating Behaviors · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (73)
Show source-provided references
1. Science and technology in high-entropy alloys10.1007/s40843-017-9195-8 ↗
2. Stainless steel in construction: a review of research, applications, challenges and opportunities10.1016/j.jcsr.2008.07.011 ↗
3. The machinability of nickel-based alloys: a review10.1016/S0924-0136(98)00314-8 ↗
4. Cobalt-based superalloys for applications in gas turbines10.1016/0025-5416(87)90061-9 ↗
5. Review of Mg alloy corrosion rates10.1016/j.jma.2020.08.002 ↗
6. Technology innovation in aluminum products10.1007/s11837-001-0115-7 ↗
7. Davis · 2001
8. Brittle intermetallic compound makes ultrastrong low-density steel with large ductility10.1038/nature14144 ↗
9. Davis · 1990
10. Nanostructured high-entropy alloys with multiple principal elements: Novel alloy design concepts and outcomes10.1002/adem.200300567 ↗
11. High-entropy alloy: challenges and prospects10.1016/j.mattod.2015.11.026 ↗
12. A critical review of high entropy alloys and related concepts10.1016/j.actamat.2016.08.081 ↗
13. Microstructural development in equiatomic multicomponent alloys10.1016/j.msea.2003.10.257 ↗
14. Fundamental deformation behavior in high-entropy alloys: an overview10.1016/j.cossms.2017.08.003 ↗
15. Microstructure and texture evolution during annealing of equiatomic CoCrFeMnNi high-entropy alloy10.1016/j.jallcom.2013.10.237 ↗
16. Mechanical properties, microstructure and thermal stability of a nanocrystalline CoCrFeMnNi high-entropy alloy after severe plastic deformation10.1016/j.actamat.2015.06.025 ↗
17. Influence of deformation and annealing twinning on the microstructure and texture evolution of face-centered cubic high-entropy alloys10.1016/j.actamat.2018.02.048 ↗
18. Heavy carbon alloyed FCC-structured high entropy alloy with excellent combination of strength and ductility10.1016/j.msea.2018.01.045 ↗
19. Effects of N addition on microstructure and mechanical properties of CoCrFeNiMn high entropy alloy produced by mechanical alloying and vacuum hot pressing sintering10.1016/j.intermet.2017.09.013 ↗
20. Boron doped ultrastrong and ductile high-entropy alloys10.1016/j.actamat.2018.04.004 ↗
21. Enhanced strength and ductility in a high-entropy alloy via ordered oxygen complexes10.1038/s41586-018-0685-y ↗
22. Beating hydrogen with its own weapon: nano-twin gradients enhance embrittlement resistance of a high-entropy alloy10.1016/j.mattod.2018.07.015 ↗
23. High-entropy alloys by mechanical alloying: a review10.1557/jmr.2019.37 ↗
24. A combinatorial assessment of AlxCrCuFeNi2 (0<x<1.5) complex concentrated alloys: microstructure, microhardness, and magnetic properties10.1016/j.actamat.2016.06.025 ↗
25. Microstructures and properties of high-entropy alloys10.1016/j.pmatsci.2013.10.001 ↗
26. Influence of manufacturing conditions on inclusion characteristics and mechanical properties of FeCrNiMnCo alloy10.3390/met10101286 ↗
27. High entropy alloys: challenges in commercialization and the road ahead
28. Manufacturing of high entropy alloys10.1007/s11837-015-1540-3 ↗
29. Mechanical and corrosion properties of additively manufactured CoCrFeMnNi high entropy alloy
30. A fracture-resistant high-entropy alloy for cryogenic applications10.1126/science.1254581 ↗
31. Characterization of non-metallic inclusions and their influence on the mechanical properties of a FCC single-phase high-entropy alloy10.1016/j.jallcom.2018.05.339 ↗
32. Oxide MnCr2O4 induced pitting corrosion in high entropy alloy CrMnFeCoNi10.1016/j.mtla.2019.100275 ↗
33. Pitting at inclusions of the equiatomic CoCrFeMnNi alloy and improving corrosion resistance by potentiodynamic polarization in H2SO410.1016/j.corsci.2021.109748 ↗
34. Microstructure and corrosion behavior of FeCrNiCoMnx (x = 1.0, 0.6, 0.3, 0) high entropy alloys in 0.5 M H2SO410.1016/j.corsci.2021.109694 ↗
35. Inclusion engineering in Co-based duplex entropic alloys10.1016/j.matdes.2021.110097 ↗
36. The ability of slags to absorb solid oxide inclusions10.2355/isijinternational.46.450 ↗
37. Improvement of steel cleanliness by controlling slag composition10.1179/030192302225004160 ↗
38. Effect of physicochemical properties of slag and flux on the removal rate of oxide inclusion from molten steel10.1007/s11663-016-0789-4 ↗
39. Chapter 1 – Introduction
40. 〈https://www.usgs.gov/centers/nmic/minerals-yearbook-metals-and-minerals#F〉.
41. Ferroalloy quality and steel cleanliness10.1179/030192310X12700328925787 ↗
42. Non-metallic inclusions in different ferroalloys and their effect on the steel quality: a review10.1007/s11663-021-02259-7 ↗
43. Three-dimensional investigations of inclusions in ferroalloys10.1002/srin.201300157 ↗
44. The purity of ferrosilicon and its influence on inclusion cleanliness of steel10.2355/isijinternational.36.Suppl_S132 ↗
45. Influence of ferromanganese additions on microalloyed engineering steel10.1179/030192303225009461 ↗
46. Oxide inclusions in ferromanganese and its influence on the quality of clean steels10.1016/S1006-706X(14)60115-1 ↗
47. Influence of ferroalloy impurities and ferroalloy addition sequence on ultra low carbon (ULC) steel cleanliness after RH treatment10.1179/030192312X13313073941699 ↗
48. Effect of LCFeCr alloy additions on the non-metallic inclusion characteristics in Ti-containing ferritic stainless steel10.1007/s11663-021-02296-2 ↗
49. Sustainable low-cost method for production of high-entropy alloys from alloy scraps10.1007/s40831-022-00523-x ↗
50. Manufacturing an ultra-low-sulfur CoCrFeMnNi high-entropy alloy by slagging through induction melting with ferroalloys feedstock10.1016/j.jallcom.2022.167080 ↗
51. Characterization of nonmetallic inclusions in high-manganese and aluminum-alloyed austenitic steels10.1007/s11661-012-1088-6 ↗
52. Edge-cracking behavior of CoCrFeMnNi high-entropy alloy during hot rolling10.1007/s12540-018-0129-0 ↗
53. Comparative corrosion behavior of Fe50Mn30Co10Cr10 dual-phase high-entropy alloy and CoCrFeMnNi high-entropy alloy in 3.5 wt% NaCl solution10.1016/j.jallcom.2020.155824 ↗
54. The influence of columnar to equiaxed transition on deformation behavior of FeCoCrNiMn high entropy alloy fabricated by laser-based directed energy deposition
55. Dislocation-induced breakthrough of strength and ductility trade-off in a non-equiatomic high-entropy alloy10.1016/j.actamat.2019.11.055 ↗
56. Activities of MnO in CaO-SiO2-Al2O3-MnO (<10 pct)-FetO(<3 pct) slags saturated with liquid iron10.1007/BF02660972 ↗
57. Thermodynamic properties of the MgAl2O4−MnAl2O4 spinel solid solution10.1007/BF02654103 ↗
58. Wagner · 1952
59. Formation and evolution of non-metallic inclusions in medium Mn steel during secondary refining process10.2355/isijinternational.ISIJINT-2017-118 ↗
60. Hino · 2010
61. The thermodynamic behavior of sulfur in molten nickel and nickel-base alloys10.1007/BF02644259 ↗
62. Al deoxidation equilibrium of Fe-10-30 mass% Mn melt at 1873 K10.2355/tetsutohagane.TETSU-2018-118 ↗
63. Deoxidation equilibria of Fe–Mn–Al melt with Al2O3 or MnAl2O4 at 1873 and 1773 K10.2355/isijinternational.ISIJINT-2020-177 ↗
64. In situ observation of the MnS precipitation behavior in high-sulfur microalloyed steel under different cooling rates10.1007/s11663-020-01946-1 ↗
65. Computational thermodynamic calculations: FactSage from CALPHAD thermodynamic database to virtual process simulation10.1007/s11663-020-01908-7 ↗
66. Deoxidation equilibrium of magnesium in liquid iron10.2355/tetsutohagane1955.83.10_623 ↗
67. Activities of the constituents in spinel solid solution and free energies of formation of MgO, MgO·Al2O310.2355/isijinternational.40.1059 ↗
68. Investigation of desulfurization of Inconel 718 superalloys by ESR type slags with different TiO2 content10.1016/j.jmrt.2019.01.027 ↗
69. Effects of remelting current on structure, composition, microsegregation, and inclusions in Inconel 718 electroslag remelting ingots10.1007/s11663-019-01685-y ↗
70. Formation mechanism of oxide-sulfide complex inclusions in high-sulfur-containing steel melts10.1007/s11663-017-1152-0 ↗
71. Prediction of inclusion evolution during refining and solidification of steel: computational simulation and experimental confirmation10.1007/s11663-020-01812-0 ↗
72. Effect of rice husk ash insulation powder on the reoxidation behavior of molten steel in continuous casting tundish10.1007/s11663-017-0971-3 ↗
73. Effect of tundish flux on compositional changes in non-metallic inclusions in stainless steel melts10.2355/isijinternational.ISIJINT-2021-167 ↗