journal article·2024-10

Comparation of non-proportional hardening behavior and microscopic mechanism for CP-Ti under strain-controlled and stress-controlled multiaxial low cycle fatigue

Tian-Hao Ma, Le Chang, Jian-Ping Zhao, Chang-Yu Zhou

Publisher page

Abstract

Proportional and non-proportional multiaxial low cycle fatigue tests were performed on commercial pure titanium (CP-Ti), employing both strain-controlled and stress-controlled modes. CP-Ti exhibits a four-stage characteristic under higher applied strain amplitude. For other cases and under stress-controlled mode, the initial hardening dissipated, giving way to a typical three-stage cyclic softening characteristics. Two failure modes, fatigue failure and ratcheting failure, occur depending on the applied stress amplitude. CP-Ti exhibits obvious asymmetric strain response under symmetric stress-controlled mode depending on the loading level. CP-Ti demonstrates non-proportional hardening under both strain-controlled mode and stress-controlled mode with different microscopic mechanisms. The additional hardening due to non-proportional loading results in an increase in the axial response stress with increasing multiaxial strain ratio. Interactions between dislocations with different slip systems hinder the development of stable dislocation structures, leading to pronounced non-proportional hardening of CP-Ti under strain-controlled mode. As for stress-controlled mode, the significant growth of twin content improves the grain boundary strength, leading to the non-proportional hardening of CP-Ti.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fatigue and fracture mechanics · Titanium Alloys Microstructure and Properties · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (57)

Show source-provided references
1. Comparisons of low cycle fatigue behavior of CP-Ti under stress and strain-controlled modes in transverse direction10.1016/j.msea.2018.12.125 ↗
2. The difference in low cycle fatigue behavior of CP-Ti under fully reversed strain and stress controlled modes along rolling direction10.1016/j.msea.2018.11.003 ↗
3. Analysis of back-weld spatters in laser welding of CP-Ti10.1016/j.jmapro.2020.01.030 ↗
4. Comparison of multiaxial low cycle fatigue behavior of CP-Ti under strain-controlled mode at different multiaxial strain ratios10.1016/j.ijfatigue.2020.105818 ↗
5. Low-cycle fatigue behavior and life prediction of CP-Ti under non-proportional and multiaxial loading10.1016/j.engfracmech.2021.107930 ↗
6. Improved rotating bending fatigue performance of laser directed energy deposited Ti6Al4V alloys by laser shock peening10.1016/j.jallcom.2024.173664 ↗
7. Recent advances on notch effects in metal fatigue: a review10.1111/ffe.13195 ↗
8. Evaluation and prediction of material fatigue characteristics under impact loads: review and prospects10.1108/IJSI-10-2021-0112 ↗
9. The RED criterion for fatigue life assessment of metals under non-proportional loading10.1016/j.ijfatigue.2022.107080 ↗
10. Stress gradient effect in metal fatigue: review and solutions10.1016/j.tafmec.2022.103513 ↗
11. Low cycle fatigue behavior of CP-Ti under multiaxial load-controlled mode at different multiaxial stress ratios10.1016/j.ijfatigue.2022.106868 ↗
12. Multiaxial fatigue of extruded ZK60 magnesium alloy10.1111/ffe.13048 ↗
13. A critical plane approach to multiaxial fatigue damage including out-of-phase loading10.1111/j.1460-2695.1988.tb01169.x ↗
14. Multiaxial fatigue damage models10.1115/1.3225980 ↗
15. Fatigue and cyclic plasticity of 304L stainless steel under axial-torsional loading at room temperature10.1016/j.ijfatigue.2019.04.009 ↗
16. An experimental evaluation of three critical plane multiaxial fatigue criteria10.1016/j.ijfatigue.2006.10.028 ↗
17. Fracture mechanisms and life assessment under high-strain biaxial cyclic loading of type 304 stainless steel10.1111/j.1460-2695.1989.tb00515.x ↗
18. Load path sensitivity and fatigue life estimation of 30CrNiMo8HH10.1016/j.ijfatigue.2011.10.009 ↗
19. Low-cycle multiaxial fatigue behaviour and fatigue life prediction for CuZn37 brass using the stress-strain models10.1016/j.ijfatigue.2017.04.011 ↗
20. Multiaxial low cycle fatigue life of Ti-6Al-4V under non-proportional loading with mean strain10.1016/j.tafmec.2017.04.004 ↗
21. On the material’s sensitivity to non-proportionality of fatigue loading10.1016/j.acme.2016.09.010 ↗
22. A survey on multiaxial fatigue damage parameters under non-proportional loadings10.1111/ffe.12659 ↗
23. Nonproportional low cycle fatigue criterion for type 304 stainless steel10.1115/1.2804541 ↗
24. Evaluation of multiaxial low cycle fatigue life for type 316L stainless steel notched specimen under non-proportional loading10.1016/j.tafmec.2016.02.007 ↗
25. A design procedure for assessing low cycle fatigue life under proportional and non-proportional loading10.1016/j.ijfatigue.2005.08.007 ↗
26. de Freitas M. Simulation of cyclic stress/strain evolutions for multiaxial fatigue life prediction10.1016/j.ijfatigue.2005.07.038 ↗
27. Strain-based multiaxial fatigue damage modelling10.1111/j.1460-2695.2005.00957.x ↗
28. Analysis of the experimental data on a low cycle fatigue under nonproportional straining10.1016/S0142-1123(00)00005-0 ↗
29. Life assessment for metallic materials with the use of the strain criterion for low-cycle fatigue10.1016/j.ijfatigue.2009.04.011 ↗
30. A new method for studying the effect of multiaxial strain states on low cycle non-proportional fatigue prediction10.1016/j.ijfatigue.2018.08.030 ↗
31. Low-cycle fatigue deformation behavior and evaluation of fatigue life on extruded magnesium alloys10.1016/j.proeng.2011.04.207 ↗
32. On the high cycle fatigue behavior of a type 304L stainless steel at room temperature10.1016/j.ijfatigue.2011.11.010 ↗
33. Multiaxial low cycle fatigue behavior and life prediction of CP-Ti under non-proportional stress-controlled mode10.1111/ffe.13870 ↗
34. Microstructure-sensitive small fatigue crack growth assessment: effect of strain ratio, multiaxial strain state, and geometric discontinuities10.1016/j.ijfatigue.2015.09.007 ↗
35. Low-cycle fatigue behavior and life prediction of TA15 titanium alloy by crystal plasticity-based modelling10.1016/j.jmrt.2023.01.063 ↗
36. ASTM-E2207-08. Standard practice for strain-controlled axial-torsional fatigue testing with thin-walled tubular specimens. Annual book of ASTM standards. vol. 03.01. 2015.
37. Influence of low cycle fatigue on deformation twins in commercial purity titanium10.1023/A:1006532227698 ↗
38. Low-cycle fatigue behaviors of commercial-purity titanium10.1016/S0921-5093(98)00650-9 ↗
39. Tensile and low-cycle fatigue behavior of commercially pure titanium and Ti–5Al–2.5Sn alloy at 293 and 77 K10.1016/S0921-5093(01)01249-7 ↗
40. Uniaxial ratchetting and low-cycle fatigue failure of the steel with cyclic stabilizing or softening feature10.1016/j.msea.2007.03.029 ↗
41. A nonproportionality parameter and a cyclic viscoplastic constitutive model taking into account amplitude dependences and memory effects of isotropic hardening
42. Low cycle fatigue behaviour of engineering metallic materials: review on cyclic deformation micro-mechanism10.1016/j.mechmat.2023.104852 ↗
43. Cycle fatigue under multiaxial stresses (in the case of combined cyclic tension-compression and cyclic torsion at room temperature
44. Cyclic plasticity for nonproportional paths: part 1—cyclic hardening, erasure of memory, and subsequent strain hardening experiments10.1115/1.3443456 ↗
45. Cyclic Deformation of 1% Cr-Mo-V Steel under Out-of-phase Loads10.1111/j.1460-2695.1979.tb01357.x ↗
46. Effect of microstructure and hardness on non-proportional cyclic hardening coefficient and predictions10.1016/j.msea.2010.01.056 ↗
47. Texture evolution and their effects on the mechanical properties of duplex Mg–Li alloy10.1016/j.jallcom.2016.01.174 ↗
48. Application of texture simulation to understanding mechanical behavior of Mg and solid solution alloys containing Li or Y10.1016/S1359-6454(01)00297-X ↗
49. Effect of temperature on microstructure and texture evolution during uniaxial tension of commercially pure titanium10.1016/j.msea.2017.07.081 ↗
50. Microstructure and texture evolution of commercial pure titanium deformed at elevated temperatures10.1016/j.msea.2009.01.065 ↗
51. Environmental effects on fatigue failure micromechanisms in titanium10.1016/S0921-5093(04)01018-4 ↗
52. Fatigue Damage Mechanism of Titanium in Vacuum and in Air10.1016/j.proeng.2012.07.350 ↗
53. A comparative assessment of iron and cobalt-based hard-facing alloy deformation using HR-EBSD and HR-DIC10.1016/j.actamat.2018.08.021 ↗
54. Tailoring properties of directed energy deposited Al-Mg alloy by balancing laser shock peening and heat treatment10.1016/j.jmst.2024.03.051 ↗
55. Geometrically necessary dislocation and size-dependent plasticity10.1016/S1359-6462(02)00329-9 ↗
56. Ultra-strong heavy-drawn eutectic high entropy alloy wire10.1016/j.actamat.2022.118515 ↗
57. Measurement of stored energy in Fe–48%Ni alloys strongly cold-rolled using three approaches: Neutron diffraction, Dillamore and KAM approaches10.1016/j.msea.2014.07.037 ↗