Yield locus and texture evolution of AA7475-T761 aluminum alloy under planar biaxial loading: An experimental and analytical study
Source abstract
Abstract
AA7475 aluminum alloy is used as a structural material in aerospace and automobile applications where complex loading conditions are applicable. The material properties under multi-axial loading are recommended for efficient component design. Hence, the mechanical behaviour of AA7475-T761 aluminium alloy was investigated through planar biaxial tensile tests. The yield locus evolution and plastic strain direction were measured at higher plastic strain values (up to 7 %) at various load ratios. The yield loci were constructed and compared with existing yield criteria. Yld2000–2d yield criterion demonstrated accurate predictions with a deviation of approximately 1 %, highlighting its effectiveness in capturing the yield behavior of AA7475. Microstructure analysis using Electron Backscatter Diffraction (EBSD) was conducted to understand the misorientation evolution under the multi-axial loading. Bulk-texture analysis was performed using X-ray diffraction method. Texture analysis revealed that uniaxial deformation favoured the development of Cube and Inverse-Copper textures, while biaxial deformation yielded split Inverse-Goss texture formation. Fractography study shows very different fracture surfaces of biaxial samples compared to uniaxial samples. Overall, this study contributes to a comprehensive understanding of the yield behavior, microstructure, and texture evolution of AA7475-T761 aluminium alloy under different loading conditions at very large strains.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal Forming Simulation Techniques · Metallurgy and Material Forming · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (88)
Show source-provided references
1. A reduced Yld2004 function for modeling of anisotropic plastic deformation of metals under triaxial loading
2. Corrosion inhibition of 7000 series aluminium alloys with cerium diphenyl phosphate10.1016/j.jallcom.2010.09.151 ↗
3. Experimental and numerical investigation of a strain rate controlled hydraulic bulge test of sheet metal10.1016/j.jmatprotec.2016.04.022 ↗
4. Investigation of size effects of very thin aluminum and copper sheets using aero-bulge test10.1016/j.msea.2010.07.076 ↗
5. Biaxial formability and microstructure of an Al-Mg-Si alloy sheet post solution heat treatment10.1016/j.jallcom.2022.163753 ↗
6. Multiaxial tube expansion test method for measurement of sheet metal deformation behavior under biaxial tension for a large strain range10.1016/j.ijplas.2012.12.003 ↗
7. High temperature shakedown of a 2nd generation nickel-base single crystal superalloy under tension-torsion loadings10.1016/j.msea.2021.142457 ↗
8. Influence of axial and torsional cyclic loading on the fatigue behavior of 304LN stainless steel using solid and hollow specimens10.1016/j.mechmat.2018.03.012 ↗
9. The M-Integral based failure description on elasto-plastic materials with defects under biaxial loading10.1016/j.mechmat.2017.06.004 ↗
10. Fracture behaviors of commercially pure titanium under biaxial tension: experiment and modeling10.1016/j.jmst.2022.08.035 ↗
11. The yielding behavior and plastic deformation of oxygen-free copper under biaxial quasi-static and dynamic loadings10.1016/j.ijsolstr.2023.112333 ↗
12. Nonlinear biaxial tensile stress path experiment without intermediate elastic unloading for validation of material model10.1016/j.ijsolstr.2022.111777 ↗
13. Plastic anisotropy evolution of SS316L and modeling for novel cruciform specimen10.1016/j.ijmecsci.2022.107663 ↗
14. Macroindentation of a soft polymer: Identification of hyperelasticity and validation by uni/biaxial tensile tests10.1016/j.mechmat.2013.05.003 ↗
15. Biaxial deformation behaviour of duplex stainless steels: Experiments and crystal plasticity based stress predictions10.1016/j.msea.2023.144597 ↗
16. Design of a biaxial tensile testing device and cruciform specimens for large plastic deformation in the central zone10.1007/s10853-019-03358-2 ↗
17. Local behavior of an AISI 304 stainless steel submitted to in situ biaxial loading in SEM10.1016/j.msea.2017.02.087 ↗
18. Numerical verification of a biaxial tensile test method using a cruciform specimen10.1016/j.jmatprotec.2012.12.007 ↗
19. Investigation on Yield Behavior of 7075-T6 Aluminum Alloy at Elevated Temperatures
20. On the modeling of deformation mechanisms in a Mg-3Al-1Zn alloy under biaxial tension10.1016/j.jmst.2022.09.051 ↗
21. Deformation mechanism of commercially pure titanium under biaxial loading at ambient and elevated temperatures10.1016/j.jmst.2022.02.027 ↗
22. Prediction and characterization of forming limits at necking from shear to equi-biaxial loading using the biaxial tensile testing method: feasibility study and application to AA6061-T410.1016/j.mechmat.2023.104598 ↗
23. Biaxial tensile behavior of Ti-6Al-4V under proportional loading10.1016/j.cja.2023.03.016 ↗
24. A new measurement technology for forming limit in aluminum alloy under biaxial dynamic loading10.1016/j.jmatprotec.2023.117963 ↗
25. Cruciform specimen design and verification for constitutive identification of anisotropic sheets10.1007/s11340-015-9999-y ↗
26. Development of a biaxial tensile machine for characterization of sheet metals10.1016/j.jmatprotec.2012.12.005 ↗
27. Determination of Yield Surfaces in Accordance With ISO 16842 Using an Optimized Cruciform Test Specimen10.1007/s11340-020-00601-9 ↗
28. Deformation behavior of commercially pure (CP) titanium under equi-biaxial tension10.1016/j.msea.2016.08.018 ↗
29. Plastic instabilities in AA5754-O under various stress states10.1088/1757-899X/418/1/012050 ↗
30. Cruciform specimen to obtain higher plastic deformation in a gauge region10.1016/j.jmatprotec.2015.07.016 ↗
31. Enlargement of measurable strain range in biaxial cruciform test
32. Development of a biaxial tensile machine for characterization of sheet metals10.1016/j.jmatprotec.2012.12.005 ↗
33. Experimental investigation of the biaxial behaviour of an aluminum sheet10.1016/j.ijplas.2003.11.012 ↗
34. Cruciform specimen machining using EDM and a new design verification for biaxial testing10.1007/s11665-020-04921-8 ↗
35. Investigation of evolving yield surfaces of dual-phase steels10.1016/j.jmatprotec.2019.116314 ↗
36. Cruciform specimen design for large plastic strain during biaxial tensile testing10.1088/1742-6596/1063/1/012160 ↗
37. Evolving asymmetric yield surfaces of quenching and partitioning steels: characterization and modeling10.1016/j.jmatprotec.2020.116979 ↗
38. Evolution of yield behavior for AA6016-T4 and DP490 - towards a systematic evaluation strategy for material models10.1016/j.ijplas.2022.103302 ↗
39. Experimental and numerical investigation of differential hardening of cold rolled steel sheet under non-proportional loading using biaxial tensile test10.1016/j.ijplas.2022.103297 ↗
40. Experimental characterization and modeling of complex anisotropic hardening in quenching and partitioning (Q&P) steel subject to biaxial non-proportional loadings10.1016/j.ijplas.2022.103347 ↗
41. Evolution of subsequent yield surfaces with plastic deformation along proportional and non-proportional loading paths on annealed AA6061 alloy: experiments and crystal plasticity finite element modeling
42. The role of brass texture on the deformation response of 7075-T651 aluminum alloy under equi-biaxial tension10.1016/j.msea.2021.141133 ↗
43. Design of a biaxial cruciform specimen with a high degree of plastic deformation and yield locus evolution10.1007/s11340-023-00958-7 ↗
44. A review of characterization and modelling approaches for sheet metal forming of lightweight metallic materials10.3390/ma16020836 ↗
45. A theory of the yielding and plastic flow of anisotropic metals
46. The anomalous behaviour of aluminium sheet under balanced biaxial tension10.1016/0020-7403(70)90087-1 ↗
47. A user-friendly theory of orthotropic plasticity in sheet metals10.1016/0020-7403(93)90061-X ↗
48. Plastic behavior and stretchability of sheet metals. Part I: A yield function for orthotropic sheets under plane stress conditions10.1016/0749-6419(89)90019-3 ↗
49. Plane stress yield function for aluminum alloy sheets - Part 1: theory10.1016/S0749-6419(02)00019-0 ↗
50. Non-quadratic yield criterion for orthotropic sheet metals under plane-stress conditions10.1016/S0020-7403(03)00139-5 ↗
51. An improved analytical description of orthotropy in metallic sheets10.1016/j.ijplas.2004.04.003 ↗
52. Influence of constitutive equations on the accuracy of prediction in sheet metal forming simulation
53. Linear transfomation-based anisotropic yield functions10.1016/j.ijplas.2004.06.004 ↗
54. On the use of homogeneous polynomials to develop anisotropic yield functions with applications to sheet forming10.1016/j.ijplas.2007.07.016 ↗
55. Anisotropic hardening and non-associated flow in proportional loading of sheet metals10.1016/j.ijplas.2009.02.003 ↗
56. On the calculation of plastic strain by simple method under non-associated flow rule10.1016/j.euromechsol.2017.08.017 ↗
57. Evolution of yield behavior for AA6016-T4 and DP490 - towards a systematic evaluation strategy for material models10.1016/j.ijplas.2022.103302 ↗
58. A yield criterion through coupling of quadratic and non-quadratic functions for anisotropic hardening with non-associated flow rule10.1016/j.ijplas.2017.08.007 ↗
59. Analytical description of an asymmetric yield function (Yoon2014) by considering anisotropic hardening under non-associated flow rule10.1016/j.ijplas.2021.102978 ↗
60. Plastic anisotropy of sheet metals under plane strain loading: a novel non-associated constitutive model based on fourth-order polynomial functions10.1016/j.matdes.2022.111187 ↗
61. A non-quadratic pressure-sensitive constitutive model under non-associated flow rule with anisotropic hardening: modeling and validation10.1016/j.ijplas.2020.102808 ↗
62. Anisotropic distortional hardening based on deviatoric stress invariants under non-associated flow rule10.1016/j.ijplas.2022.103214 ↗
63. Modeling stress anisotropy, strength differential, and anisotropic hardening by coupling quadratic and stress-invariant-based yield functions under non-associated flow rule10.1016/j.mechmat.2022.104458 ↗
64. Characterization of the asymmetric evolving yield and flow of 6016-T4 aluminum alloy and DP490 steel10.1016/j.jmst.2022.05.040 ↗
65. A new anisotropic-asymmetric yield criterion covering wider stress states in sheet metal forming10.1016/j.ijplas.2023.103653 ↗
66. A coupled yield criterion for anisotropic hardening with analytical description under associated flow rule: modeling and validation10.1016/j.ijplas.2020.102882 ↗
67. Sato · 2006
68. Towards ductilization of high strength 7XXX aluminium alloys via microstructural modifications obtained by friction stir processing and heat treatments10.1016/j.mtla.2021.101248 ↗
69. Effect of pre-aging process on microstructure and properties of 7075-T8 aluminium alloy10.1016/j.jallcom.2023.170953 ↗
70. Texture and formability studies on AA7020 Al alloy sheets10.1016/j.msea.2012.08.024 ↗
71. Microstructure and texture evolution in cryorolled Al 7075 alloy10.1016/j.jallcom.2010.02.111 ↗
72. An experimental and numerical study on the formability of textured AlZnMg alloys10.1016/j.euromechsol.2007.06.003 ↗
73. Mechanical response and texture evolution of AZ31 alloy at large strains for different strain rates and temperatures10.1016/j.ijplas.2010.08.009 ↗
74. Quasi-static and dynamic response, and texture evolution of two overaged Al 7056 alloy plates in T761 and T721 tempers: experiments and modeling10.1016/j.ijplas.2020.102679 ↗
75. The effect of microstructure on the mechanical behavior and fracture mechanism in a 7050-T76 aluminum alloy10.1016/0921-5093(91)90697-L ↗
76. Effect of microstructure and strength on the fracture behavior of AA2219 alloy10.1016/j.msea.2008.11.024 ↗
77. Effect of pre-stretching deformation treatment process on microstructure and mechanical properties of Al-Cu-Mg alloy
78. Second phase particles and mechanical properties of 2219 aluminum alloys processed by an improved ring manufacturing process10.1016/j.msea.2020.139226 ↗
79. González-velázquez · Struct. Integr. 3 Fractography Fail. Anal. · 201810.1007/978-3-319-76651-5 ↗
80. Quantitative assessment of the impact of second phase particle arrangement on damage and fracture anisotropy10.1016/j.actamat.2018.02.003 ↗
81. Dislocation density evolution of AA 7020-T6 investigated by in-situ synchrotron diffraction under tensile load10.1016/j.matchar.2015.09.004 ↗
82. Influence of out-of-plane stretch forming induced different strain paths on micro-texture evolution, slip system activity and Taylor factor distribution in Al–Li alloy10.1016/j.msea.2021.142267 ↗
83. Microstructure and texture evolution during annealing a cryogenic-SPD processed Al-alloy with a nanoscale lamellar HAGB grain structure10.1016/j.actamat.2009.04.010 ↗
84. Effects of cold working degrees on grain boundary characters and strain concentration at grain boundaries in Alloy 60010.1016/j.corsci.2010.11.022 ↗
85. Quasi-static and dynamic response, and texture evolution of two overaged Al 7056 alloy plates in T761 and T721 tempers: experiments and modeling10.1016/j.ijplas.2020.102679 ↗
86. Mechanical performance improvement of Al–Cu–Mg using various thermomechanical treatments10.1016/j.msea.2022.142869 ↗
87. Effect of strain path change on the evolution of texture and microstructure during rolling of copper and nickel10.1016/j.msea.2011.06.062 ↗
88. The effects of texture on formability of aluminum alloy sheets10.1016/j.actamat.2007.04.014 ↗