journal article·2024-05

Effect of Mn substitution on Cr in the Al-Cu-Er-Mg-Zr-Fe-Si-Ti cast alloy

Sayed M. Amer, Maria V. Glavatskikh, Ruslan Yu. Barkov, Irina S. Loginova, Andrey V. Pozdniakov

Publisher page

Abstract

The microstructure, phase composition, precipitates evaluation, casting, and mechanical properties of the novel cast Al-4Cu-2.1Er-1Mg-0.2Zr-0.2Cr-0.15Fe-0.15Si-0.1Ti alloy were analyzed using by optical microscope, scanning and transmission electron microscopes, differential scanning calorimetry, thermodynamic calculations, hot cracking and mechanical properties measurements. The positive effect of Cr as a substitution of Mn on plasticity and precipitation strengthening was demonstrated. The 0.2Zr, 0.2Cr and 0.1 Ti as a grain refiners provide a fine grain size of 25 μm in the as-cast state due to primary Al 75–80Cu 10–12Er 3–4Cr 7 phase particles formation as a nucleation centers of Al. The hot cracking index (HCI) of the AlCuErMgCr alloy was 12–14 mm which is similar with HCI of the cast Al-Si-Cu-Mg alloys. The good casting properties in the AlCuErMgCr alloy achieved due to a fine grain structure and narrow solidification range. The contribution of the Al 3(Zr,Er) (40 nm), Al 45Cr 7 (6 nm), and S’(θ’) (100/5 nm) precipitates is 38.5 MPa, 140.4 MPa, and 198.9 MPa and the calculated contribution from dislocation and precipitates is 262.3 MPa. The ultimate tensile strength (UTS) and elongation (El.) of the AlCuErMgCr alloy are 372 MPa and 6% which is higher in 16.6% and 150%, respectively, than in the Mn-containing alloy. Novel alloy has an excellent combination of yield strength (YS) and plasticity at 20–250°C. The YS and El. are 301 MPa and 6% and 225–250 MPa and 4.6–11.5% at 20 and 200–250°C, respectively. The rupture strength at 250°C after 100 h ( σ 100 250 ) is 106 MPa. Mechanical and casting properties of the novel alloy are superior to the properties of commercial 201.0 (Al-Cu-Mn-Mg-Ag-Ti) alloy.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (58)

Show source-provided references
1. Zolotorevsky · 2007
2. Mechanical properties in the semi-solid state and hot tearing of aluminium alloys10.1016/S0079-6425(03)00037-9 ↗
3. Determining hot cracking index of Al–Si–Cu–Mg casting alloys calculated using effective solidification range10.1179/1743133613Y.0000000096 ↗
4. Search for promising compositions for developing new multiphase casting alloys based on Al-Cu-Mg matrix using thermodynamic calculations and mathematic simulation10.1134/S0031918X13120107 ↗
5. Structure, phase composition, and strengthening of cast Al–Ca–Mg–Sc alloys10.1134/S0031918X16020046 ↗
6. Effect of Calcium and Silicon on the Character of Solidification and Strengthening of the Al–8% Zn–3% Mg Alloy10.1134/S0031918X20020155 ↗
7. Microstructure and phase composition of Al-Ce-Cu alloys in the Al-rich corner10.4028/www.scientific.net/MSF.519-521.395 ↗
8. Structure and phase composition of alloys of the Al-Ce-Cu system in the region of the Al-Al8CeCu4 quasi-binary join10.3103/S1067821207010099 ↗
9. Microstructure and materials characterisation of the novel Al–Cu–Y alloy10.1080/02670836.2018.1460536 ↗
10. Comparative Analysis of Structure and Properties of Quasibinary Al–6.5Cu–2.3Y and Al–6Cu–4.05Er Alloys10.1134/S0031918X20030023 ↗
11. Evolution of Microstructure and Mechanical Properties of a New Al–Cu–Er Wrought Alloy10.1134/S0031918X19060097 ↗
12. Microstructure and mechanical properties of novel quasibinary al-cu-yb and al-cu-gd alloys
13. The Y–Cu–Al system10.1016/S0925-8388(02)00873-3 ↗
14. Thermodynamic description of the Al–Cu–Y ternary system, CALPHAD: Comp. Coup. of Ph
15. Phase relationships in the Al-rich region of the Al–Cu–Er system10.1016/j.jallcom.2010.12.029 ↗
16. Thermodynamic assessment of the Al–Cu–Er system
17. Thermodynamic description of the al-cu-yb ternary system supported by first-principles calculations10.2298/JMMB150709013H ↗
18. Thermodynamic assessment of the Al-Cu-Gd system Calphad Comput10.1016/j.calphad.2009.08.003 ↗
19. Thermal Stability of Aluminum Alloys10.3390/ma13153441 ↗
20. Cerium in aluminum alloys10.1007/s10853-019-03892-z ↗
21. On the Al–Al11Ce3 Eutectic Transformation in Aluminum–Cerium Binary Alloys10.3390/ma13204549 ↗
22. Structure and Properties of New Heat-Resistant Cast Alloys Based on the Al–Cu–Y and Al–Cu–Er Systems10.1134/S0031918X21090027 ↗
23. Structure and Properties of New Wrought Al – Cu – Y- and Al – Cu – Er-Based Alloys10.1134/S0031918X21080020 ↗
24. Microstructure and Mechanical Properties of Novel Heat Resistant Cast Al-Cu-Yb(Gd)-Mg-Mn-Zr Alloys10.3390/met12122079 ↗
25. Synergetic effect of Er and Zr on the precipitation hardening of Al–Er–Zr alloy10.1016/j.scriptamat.2011.06.033 ↗
26. Precipitation evolution and coarsening resistance at 400 °C of Al microalloyed with Zr and Er10.1016/j.scriptamat.2012.03.026 ↗
27. Precipitation evolution in Al–Er–Zr alloys during aging at elevated temperature10.1016/j.jallcom.2013.03.237 ↗
28. Effects of minor Zr and Er on microstructure and mechanical properties of pure aluminum10.1016/j.msea.2013.05.035 ↗
29. Effects of Er and Zr additions on precipitation and recrystallization of pure aluminum10.1016/j.scriptamat.2012.09.026 ↗
30. Effect of Zr on microstructure and mechanical properties of the Al–Cu–Er alloy10.1080/02670836.2019.1709689 ↗
31. Effect of Homogenization Treatment Regime on Microstructure, Recrystallization Behavior, Mechanical Properties, and Superplasticity of Al-Cu-Er-Zr Alloy10.1007/s11837-021-04766-z ↗
32. Creep behavior of heat resistant Al–Cu–Mn alloys strengthened by fine (θ′) and coarse (Al20Cu2Mn3) second phase particles10.1016/j.msea.2019.138062 ↗
33. Comparative analysis of structure evolution and thermal stability of сommercial AA2219 and model Al-2 wt%Mn-2 wt%Cu cold rolled alloys10.1016/j.jallcom.2021.158823 ↗
34. Creep behavior of heat resistant Al–Cu–Mn alloys strengthened by fine (θ′) and coarse (Al20Cu2Mn3) second phase particles10.1016/j.msea.2019.138062 ↗
35. The Phase Composition and Mechanical Properties of the Novel Precipitation-Strengthening Al-Cu-Er-Mn-Zr Alloy10.3390/app10155345 ↗
36. Effect of Mn Addition on the Phase Composition and Strengthening Behavior of AlCuYbZr and AlCuGdZr Alloys10.1007/s11837-022-05398-7 ↗
37. The synergistic effects of nano-sized α-Al(Mn,Cr,Fe)Si and Al–Si–Zr dispersoids on the creep behavior Al–Si–Mg–Cu (Mn, Cr, Zr) diesel engine alloy10.1016/j.msea.2023.144949 ↗
38. On the strengthening effect of Al-Cr-Si dispersoid in an Al-Si-Mg-Cu casting alloy with Cr addition10.1016/j.matchar.2020.110457 ↗
39. Effect of trace Cr alloying on centerline segregations in sub-rapid solidified Al–Mg–Si (AA6061) alloys fabricated by twin-roll casting10.1016/j.msea.2021.141896 ↗
40. Heat treatment of the new high-strength high-ductility Al–Mg–Si–Mn alloys with Sc, Zr and Cr additions10.1016/j.mtla.2020.100981 ↗
41. Microstructure and stress corrosion cracking resistance of Al-6.5Zn-2Cu-1.5Mg-0.05Ti alloy modified by Cr addition10.1016/j.matchar.2021.111621 ↗
42. Atomic-scale investigation of the heterogeneous precipitation in the E (Al18Mg3Cr2) dispersoid of 7075 aluminum alloy10.1016/j.jallcom.2020.156890 ↗
43. Precipitates and precipitation behavior in Al–Zr–Yb–Cr alloys10.1016/j.matlet.2012.02.013 ↗
44. A model for the yield strength of overaged Al–Zn–Mg–Cu alloys10.1016/S1359-6454(03)00363-X ↗
45. Influence of predeformation and ageing of an Al–Zn–Mg alloy—II. Modeling of precipitation kinetics and yield stress10.1016/S1359-6454(98)00296-1 ↗
46. Mechanical behavior and strengthening mechanisms in ultrafine grain precipitation-strengthened aluminum alloy10.1016/j.actamat.2013.09.042 ↗
47. Achieving ultra-high strength of Al-Cu-Li alloys by the combination of high pressure torsion and age-hardening10.1016/j.msea.2021.142504 ↗
48. Microstructural evolution, strengthening and thermal stability of an ultrafine-grained Al–Cu–Mg alloy10.1016/j.actamat.2016.02.050 ↗
49. Modeling the age-hardening behavior of Al-Si-Cu alloys10.1007/s11661-006-0221-9 ↗
50. Study of work hardening of quenched and naturally aged Al–Mg and Al–Cu alloys10.1016/j.msea.2008.10.010 ↗
51. Microstructure and mechanical properties of Al–Mg–Er sheets jointed by friction stir welding10.1016/j.matdes.2013.05.100 ↗
52. Structure and Properties of Al–4.5Mg–0.15Zr Compositions Alloyed with Er, Y, and Yb10.1134/S0031918X22050088 ↗
53. Effect of Minor Cr, Mn, Zr, Ti and B on Grain Refinement of As-Cast Al-Zn-Mg-Cu Alloys10.1016/S1875-5372(10)60108-7 ↗
54. S.M. Amer, M.V. Glavatskikh, R.Yu Barkov, I.S. Loginova, A.V. Pozdniakov. Effect of chromium on microstructure and mechanical properties of the Al-Cu-Er-Zr alloy. Metallurgist (2024) in press.10.3390/met13020349 ↗
55. Diffusion controlled early-stage L12-D023 transitions within Al3Zr10.1016/j.scriptamat.2023.115460 ↗
56. On the formation of anti-phase boundaries and interphase boundaries in Al3Zr precipitates of Al-Cu-Zr alloy studied at atomic scale10.1016/j.jallcom.2021.161442 ↗
57. Precipitation evolution in Al–Zr and Al–Zr–Ti alloys during aging at 450–600°C10.1016/j.actamat.2007.11.011 ↗
58. Al-Er (Aluminum-Erbium)10.1007/s11669-011-9877-y ↗