journal article·2024-05

Tailoring heat treatment for AlSi7Mg0.6 parts with as-built surface generated by laser powder bed fusion to reduce surface roughness sensitivity

Konrad Gruber, Irina Smolina, Robert Dziedzic, Wojciech Stopyra, Michał Karoluk, Bogumiła Kuźnicka, Tomasz Kurzynowski

Publisher page

Abstract

The most important advantage of additive manufacturing by laser powder bed fusion (PBF-LB) technique is the ability to produce geometrically complex parts, but the problem is their rough surfaces, often difficult or inaccessible to finish by machining. Therefore, research to improve the reproducibility of the mechanical behavior of parts manufactured from aluminum alloy powders with as-built surfaces is of vital importance for the aerospace and automotive industries. Since local notches occurring on rough surfaces after the PBF-LB process are unavoidable, the way to solve this problem is to obtain as-built surfaces of the highest possible quality and to adapt a post-process heat treatment that increases the ductility and fracture toughness of the material. To this end, the present work focused on the study of the mechanical performance of AlSi7Mg0.6 samples with a rough as-built surface in the as-built state and after several variants of post-process heat treatment, combined with a detailed analysis of the microstructures corresponding to these states. Tensile samples built on a platform preheated to 100 °C, achieved a relative density of 99.85%, satisfactory surface quality, a relatively low level of residual stress and moderate crystallographic texture. Despite the rough surface, the samples under the as-built condition and after different variants of heat treatment (direct aging (DA), stress relieving (SR), and solution annealing followed by artificial aging (T6)), achieved tensile properties comparable to those reported in the literature for PBF-LB samples with machined surfaces. The resulting combinations of tensile properties of PBF-LB samples after different heat treatment variants were evaluated using the quality index (QI) commonly used to assess the quality of heat-treated Al-Si-Mg castings. It was found that the proposed T6 treatment provides the best combination of strength properties and ductility, compared to those obtained after both DA and SR, as well as after T6 treatment of high-quality castings, from the point of view of reducing the sensitivity of AlSi7Mg0.6 alloy to surface roughness.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (46)

Show source-provided references
1. Metal additive manufacturing in aerospace: a review10.1016/j.matdes.2021.110008 ↗
2. A review of laser powder bed fusion additive manufacturing of aluminium alloys: microstructure and properties
3. Solidification and precipitation behaviour of Al-Si-Mg casting alloys10.1023/A:1004801327556 ↗
4. Analysis of the high growth-rate transition in Al-Si eutectic solidification10.1007/s10853-009-3747-6 ↗
5. Influence of cooling condition after solidification on T5 heat treatment response of hypoeutectic Al-7Si-0.4Mg casting alloy10.1016/j.jallcom.2022.164339 ↗
6. Changes in the microstructure and mechanical properties of additively manufactured AlSi10Mg alloy after exposure to elevated temperatures10.1016/j.matchar.2018.01.028 ↗
7. Effect of heat treatments on microstructure and mechanical properties of AlSi7Mg fabricated by selective laser melting10.1007/s11665-021-06324-9 ↗
8. Study of AlSi7Mg0.6 alloy by selective laser melting: mechanical properties, microstructure, heat treatment
9. Unravelling the multi-scale structure–property relationship of laser powder bed fusion processed and heat-treated AlSi10Mg10.1038/s41598-021-85047-2 ↗
10. Heat treatment of aluminium alloys produced by laser powder bed fusion: a review10.1016/j.matdes.2021.109651 ↗
11. Rapid solidification and non-equilibrium phase constitution in laser powder bed fusion (LPBF) of AlSi10Mg Alloy: analysis of nano-precipitates, eutectic phases, and hardness evolution10.1007/s11661-019-05505-5 ↗
12. The influence of processing parameters on aluminium alloy A357 manufactured by Selective Laser Melting10.1016/j.matdes.2016.07.009 ↗
13. Effect of heat treatment on the microstructure and anisotropy in mechanical properties of A357 alloy produced by selective laser melting10.1016/j.matdes.2018.05.026 ↗
14. Effect of process and post-process conditions on the mechanical properties of an A357 alloy produced via laser powder bed fusion10.3390/met7020068 ↗
15. Heat treatment optimization via thermo-physical characterization of AlSi7Mg and AlSi10Mg manufactured by laser powder bed fusion (LPBF)
16. Aging Profiles of AlSi7Mg0.6 and AlSi10Mg0.3 alloys manufactured via laser-powder bed fusion: direct aging versus T6
17. Tuning the microstructure and mechanical properties of AlSi10Mg alloy via in-situ heat-treatments in laser powder bed fusion10.1016/j.msea.2023.145268 ↗
18. Comparison of AlSi7Mg0.6 alloy obtained by selective laser melting and investment casting processes: microstructure and mechanical properties in as-built/as-cast and heat-treated conditions10.1016/j.msea.2020.139124 ↗
19. Killer notches: The effect of as-built surface roughness on fatigue failure in AlSi10Mg produced by laser powder bed fusion
20. Side surface topography generation during laser powder bed fusion of AlSi10Mg
21. Influence of contour scan variation on surface, bulk and mechanical properties of LPBF-processed AlSi7Mg0.6
22. Combined effect of surface anomalies and volumetric defects on fatigue assessment of AlSi7Mg fabricated via laser powder bed fusion
23. A comparison of fatigue strength sensitivity to defects for materials manufactured by AM or traditional processes10.1016/j.ijfatigue.2016.06.020 ↗
24. Effect of build orientation on fracture and tensile behavior of A357 Al alloy processed by Selective Laser Melting10.1016/j.msea.2019.138392 ↗
25. Influence of the AlSi7Mg0.6 aluminium alloy powder reuse on the quality and mechanical properties of LPBF samples
26. Role of direct aging and solution treatment on hardness, microstructure and residual stress of the A357 (AlSi7Mg0.6) alloy produced by powder bed fusion10.1007/s11663-021-02179-6 ↗
27. Short heat treatments for the F357 aluminum alloy processed by laser powder bed fusion
28. Effects of annealing on the microstructure and mechanical properties of selective laser melted AlSi7Mg alloy10.1016/j.msea.2018.10.047 ↗
29. Microstructure and strength of selectively laser melted AlSi10Mg10.1016/j.actamat.2016.07.012 ↗
30. Impact of high temperature stress relieving on final properties of Inconel 718 processed by laser powder bed fusion10.1016/j.msea.2021.141111 ↗
31. Microstructural analysis of the influences of platform preheating and post-build heat treatment on mechanical properties of laser powder bed fusion manufactured AlSi10Mg alloy10.1016/j.msea.2023.145486 ↗
32. Solid solution hardening in supersaturated AlMgSi alloy10.2320/matertrans.MT-M2019190 ↗
33. Metals handbook desk edition
34. Influence of Si precipitates on fracture mechanisms of AlSi10Mg parts processed by Selective Laser Melting10.1016/j.actamat.2019.06.013 ↗
35. W. Kurz, D.J. Fisher, Fundamentals of Solidification 4th, 4th ed., 1998. 〈https://www.scientific.net/book/fundamentals-of-solidification-4th/978-3-0357-3239-9〉 (accessed October 28, 2023).
36. Numerical analysis of heat transfer during multi-layer selective laser melting of AlSi10Mg10.1016/j.ijleo.2016.06.115 ↗
37. Partially melted zone in aluminum welds-planar and cellular solidification
38. Glicksman · 2011 · 370
39. Atomic radii in crystals10.1063/1.1725697 ↗
40. Multiple precipitation pathways in an Al-7Si-0.6Mg alloy fabricated by selective laser melting10.1016/j.scriptamat.2018.09.045 ↗
41. Solute nanostructures and their strengthening effects in Al-7Si-0.6Mg alloy F35710.1016/j.actamat.2011.10.029 ↗
42. A357 Alloy by LPBF for industry applications10.3390/ma13071488 ↗
43. A rationale for the quality index of Al-Si-Mg casting alloys10.1080/13640461.2000.11819376 ↗
44. The origins for tensile properties of selective laser melted aluminium alloy A357
45. Understanding quality in aluminum castings
46. Defect analysis for additively manufactured materials in fatigue from the viewpoint of quality control and statistics of extremes10.1016/j.prostr.2019.12.014 ↗