Failure mechanism of single-crystal superalloy NiAlReRu components with film cooling holes under the coupling high-speed rotating and high temperature condition
Source abstract
Abstract
In order to make up for the deficiency that the laboratory testing of standard samples cannot approximately simulate the turbine blade geometry and service environment, the creep experiment of the nickel-based single crystal superalloy NiAlReRu components with film cooling holes (FCHs) is carried out under the coupling high-speed rotating and high temperature condition. The component with the FCHs exposed to the coupling high-speed rotating of 20000 rpm and high temperature of 1000 ℃ continuously lasts 255.92 h until it breaks. The microstructural evolution and fracture process are analyzed. The results indicate that the existence of the FCHs evidently changes the stress distribution of the region with the FCHs, which makes the microstructural evolution of γ′ phase significantly different. The component is fractured along the second row of the FCHs and the normal direction of the fracture surface is basically parallel to the centrifugal force direction. The fracture process can be divided into three typical stages. The coupling effect of temperature and stress on the failure mechanism is discussed.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: High Temperature Alloys and Creep · Turbomachinery Performance and Optimization · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (34)
Show source-provided references
1. The effect of stress state on rafting mechanism and cyclic creep behavior of Ni-base superalloy10.1016/j.mechmat.2020.103563 ↗
2. Evolution of Ni-based superalloys for single crystal gas turbine blade applications10.1016/S1270-9638(99)00108-X ↗
3. A review of shaped hole turbine film-cooling technology10.1115/1.1860562 ↗
4. Gas turbine film cooling10.2514/1.18034 ↗
5. Assessment of various film-cooling configurations including shaped and compound angle holes based on large-scale experiments10.1115/1.1515337 ↗
6. Ieee, new approach to the inspection of cooling holes in aero-engines10.1109/MESA.2008.4735655 ↗
7. Oxidation behavior of recast layer of air-film hole machined by EDM technology of Ni-based single crystal blade and its effect on creep strength
8. Gas turbine aero-engine first stage turbine blade failure investigation10.1115/1.3078782 ↗
9. Influence of Cooling Holes Distribution on High Cycle Fatigue Fracture Behavior of DD6 Single Crystal Superalloy
10. Low cycle fatigue fracture mechanism of a modeling specimen with cooling film hole of DD6 single crystal superalloy
11. Thermomechanical fatigue on the nickel based single crystal superalloy DD6 with film cooling hole
12. Creep rupture mechanism and microstructure evolution around film-cooling holes in nickel-based single crystal superalloy specimen10.1016/j.engfracmech.2020.107187 ↗
13. Anisotropic creep fracture mechanism and microstructural evolution in nickel-based single crystal specimen with a center film hole10.1016/j.tafmec.2020.102680 ↗
14. Surface slip deformation characteristics of nickel-base single crystal thin plates with film cooling holes10.1109/ACCESS.2020.2989034 ↗
15. Creep-fatigue rupture mechanism and microstructure evolution around film-cooling holes in nickel-based DS superalloy specimen10.1016/j.intermet.2021.107359 ↗
16. Experimental investigation on low cycle fatigue properties of Ni-based alloy with single hole10.3139/146.111904 ↗
17. The inter-hole interference on creep deformation behavior of nickel-based single crystal specimen with film-cooling holes10.1016/j.ijmecsci.2019.105090 ↗
18. Tensile behavior of single-crystal superalloy with different structured cooling holes10.1016/j.ijmecsci.2022.107514 ↗
19. In-situ observation of crack initiation and propagation in Ni-based superalloy with film cooling holes during tensile test10.1016/j.jallcom.2019.04.139 ↗
20. Crystallographic failure analysis of film near cooling hole under temperature gradient of nickel-based single crystal superalloys10.1016/j.tafmec.2006.11.007 ↗
21. Experimental and numerical modeling of the stress rupture behavior of nickel-based single crystal superalloys subject to multi-row film cooling holes
22. Effect of film-hole configuration on creep rupture behavior of a second generation nickel-based single crystal superalloys10.1016/j.matchar.2017.06.019 ↗
23. Microstructure stability of 4th Generation Single Crystal Superalloy, PWA 1497, during high temperature creep deformation10.2320/matertrans.MB201003 ↗
24. High-temperature tensile creep behavior of A [001] orientation single crystal nickel-base superalloy
25. Microstructure and high-temperature strength of monocrystalline nickel-base superalloys10.1002/1527-2648(200006)2:6<319::AID-ADEM319>3.0.CO;2-S ↗
26. Microstructure evolution mechanisms in nickel-based single crystal superalloys under multiaxial stress state10.1016/j.jallcom.2019.05.143 ↗
27. Dependence of the high-temperature low-cycle fatigue behaviour of the monocrystalline nickel-base superalloys CMSX-4 and CMSX-6 on the γ/γ′-morphology10.1016/S0921-5093(99)00453-0 ↗
28. Thermomechanical fatigue of a directionally-solidified Ni-base superalloy: smooth and cylindrically-notched specimens10.1016/j.ijfatigue.2010.02.002 ↗
29. Failure analysis of a gas turbine blade made of Inconel 738LC alloy10.1016/j.engfailanal.2004.10.002 ↗
30. Failure analysis towards reliable performance of aero-engines10.14429/dsj.49.3843 ↗
31. Effect of stress state on microstructure of DD5 single crystal superalloy
32. W.P. Wu, Y.F. Guo, Y.S. Wang, 2006. Finite element analysis of gamma-phase raft mechanism in Ni-based single crystal superalloy, 16 (2006) S1990-S1994.
33. Effect of applied stress on gamma '-rafting behavior in a Ni-based single-crystal superalloy: experiments and finite element analysis, J10.1007/s42243-018-0076-5 ↗
34. Effect of stress distribution around original pore defects on microstructure evolution of Ni-based single crystal superalloy