Research on anisotropy of the 7B50 super thick plate
Source abstract
Abstract
In this study, the microstructure and in-plane anisotropy (IPA) of mechanical properties along the normal direction (ND) of the 7B50 Al super thick plate are mainly studied. When adopting the same heat treatment for the experiment, higher degree of recrystallization is displayed on the surface of the plate and lower degree is achieved in the center along the ND. The main textures developed through the plate are Brass, Cube, Copper and R textures. The maximum texture density along the ND occurs at the center and there exists a complex stress condition, resulting in the texture weakening at 10 mm & SIM; 20 mm depth from the rolling surface. Considering the final mechanical properties, the IPA is not substantial along the ND com-pared with thin plates in other studies and the differences in tensile properties are mainly embodied in the nonuniform elongation. The main reason for this phenomenon may be attributed to the fact that growth and aggregation of micropores along the transverse direction (TD) are easier.& COPY; 2023 Published by Elsevier B.V.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (49)
Show source-provided references
1. Synergy in hybrid multi-scale particles for the improved formability of Al–Zn–Mg–Cu alloys10.1016/j.jmrt.2020.12.068 ↗
2. Effect of various aging treatment on thermal stability of a novel Al-Zn-Mg-Cu alloy for oil drilling10.1016/j.msea.2020.140490 ↗
3. Enhanced stiffness of Al–Zn–Mg–Cu alloys via heterogeneous structure of soft and hard microdomains10.1016/j.msea.2022.143028 ↗
4. Effect of minor Sc and Zr on recrystallization behavior and mechanical properties of novel Al–Zn–Mg–Cu alloys10.1016/j.jallcom.2015.10.122 ↗
5. Microstructures and tensile properties of a selective laser melted Al–Zn–Mg–Cu (Al7075) alloy by Si and Zr microalloying10.1016/j.msea.2020.139492 ↗
6. Heat treatment of 7xxx series aluminium alloys—Some recent developments10.1016/S1003-6326(14)63306-9 ↗
7. Prediction of properties distribution of 7B50 alloy thick plates after quenching and aging by quench factor analysis method10.1007/s12598-018-1083-1 ↗
8. Effect of thermal exposure on microstructure and mechanical properties of friction stir welding 7B50-T7451 aluminium alloy thick plate joint10.1016/j.jmrt.2021.11.082 ↗
9. Creep aging behavior and performance of Al-Zn-Mg-Cu alloys under different parameters in retrogression aging treatment10.1007/s11771-022-4955-3 ↗
10. Effects of shot peening with different coverage on surface integrity and fatigue crack growth properties of 7B50-T7751 aluminum alloy10.1016/j.engfailanal.2021.106010 ↗
11. Effects of Ultrasonic surface rolling on the localized corrosion behavior of 7B50-T7751 aluminum alloy10.3390/ma13030738 ↗
12. Influence of ultrasonic rolling on surface integrity and corrosion fatigue behavior of 7B50-T7751 aluminum alloy10.1016/j.ijfatigue.2019.04.005 ↗
13. The fracture behavior of 7085-T74 Al alloy ultra-thick plate during high cycle fatigue10.1007/s11661-020-05759-4 ↗
14. Deformation and strengthening behaviors of Al–Cu–Mg alloy thick plate during hot forming-quenching integrated process10.1016/j.jmrt.2021.12.069 ↗
15. Study on microstructure and fracture characteristics of 5083 aluminum alloy thick plate10.1016/j.jallcom.2020.153960 ↗
16. Anisotropy of localized corrosion in 7050–T7451 Al alloy thick plate10.1016/S1003-6326(13)62758-2 ↗
17. Anisotropy in fatigue crack propagation behavior of Al-Cu-Li alloy thick plate10.1016/j.matchar.2017.07.025 ↗
18. Effect of solution treatment on recrystallization, texture and mechanical properties of 7A65-T74 aluminum alloy super-thick hot rolled plate10.1007/s11595-022-2552-9 ↗
19. Effect of the initial texture, recrystallization and Re-dissolution process on the evolution of texture during solution treatment of the 7A65 hot rolled plate10.3390/met12010008 ↗
20. Microstructure and mechanical properties of dissimilar double-side friction stir welds between medium-thick 6061-T6 aluminum and pure copper plates10.1007/s40195-022-01436-0 ↗
21. Effects of heat treatment on the microstructure, texture and mechanical property anisotropy of extruded 2196 Al-Cu-Li alloy10.1016/j.jallcom.2020.158102 ↗
22. Modeling plasticity of an aluminum 2024T351 thick rolled plate for cold forming applications10.1016/j.ijsolstr.2020.05.005 ↗
23. Improvement in the anisotropic mechanical properties and formability of Al–Si–Mg–Cu-based alloy sheets10.1016/j.msea.2020.140199 ↗
24. Study on a new retrogression and re-aging treatment of spray formed Al-Zn-Mg-Cu alloy10.1557/jmr.2016.44 ↗
25. Modeling the precipitation kinetics and tensile properties in Al-7Si-Mg cast aluminum alloys10.1016/j.msea.2016.12.042 ↗
26. Modeling precipitation hardening and yield strength in cast Al-Si-Mg-Mn alloys10.3390/met10101356 ↗
27. Novel strategy of electroshock treatment for improving mechanical performances of Al-Zn-Mg-Cu alloy by edge dislocation increment10.1016/j.msea.2022.143805 ↗
28. Effect of aging state on fatigue property of wrought aluminum alloys10.1016/j.ijfatigue.2021.106682 ↗
29. Examining the effect of the aging state on strength and plasticity of wrought aluminum alloys10.1016/j.jmst.2021.11.075 ↗
30. Experimental investigation and modelling of yield strength and work hardening behaviour of artificially aged Al-Cu-Li alloy10.1016/j.matdes.2019.108121 ↗
31. Effect of quenching rate and its coupling model on precipitation and strength of Al–Cu–Cd alloys10.1016/j.msea.2019.06.032 ↗
32. Microstructural evolution and strengthening mechanisms in a heat-treated additively manufactured Al–Cu–Mn–Zr alloy10.1016/j.msea.2022.142928 ↗
33. Process model to predict yield strength of AA6063 alloy10.1016/j.msea.2015.07.070 ↗
34. Quantitative prediction of the mechanical properties of precipitation-hardened alloys with special application to Al–Mg–Si10.1016/j.msea.2017.07.080 ↗
35. Prediction of aging kinetics and yield strength of 6063 alloy10.1007/s11665-019-04086-z ↗
36. Modeling the hardness and yield strength evolutions of aluminum alloy with rod/needle-shaped precipitates10.1016/j.msea.2006.08.025 ↗
37. Yield strength prediction of rolled Al−(1.44−12.40)Si−0.7Mg alloy sheets under T4 condition10.1016/S1003-6326(20)65359-6 ↗
38. Strength behavior of circular concrete-filled steel tube stub columns under axial compression: a review10.1016/j.conbuildmat.2021.126144 ↗
39. An investigation on the anisotropic plastic behavior and forming limits of an Al-Mg-Li Alloy sheet10.1007/s11665-021-05981-0 ↗
40. Influence of microstructural and crystallographic inhomogeneity on tensile anisotropy in thick-section Al–Li–Cu–Mg plates10.1016/j.msea.2021.142135 ↗
41. Influence of aging treatment on the microstructure, mechanical properties and anisotropy of hot extruded Al-Mg-Si plate10.1016/j.matdes.2019.107999 ↗
42. Effects of heat treatment on the microstructure, texture and mechanical property anisotropy of extruded 2196 Al-Cu-Li alloy10.1016/j.jallcom.2020.158102 ↗
43. Microstructure evolution and physical-based diffusion constitutive analysis of Al-Mg-Si alloy during hot deformation10.1016/j.matdes.2019.108181 ↗
44. Effect of mushy state rolling on the microstructure, microhardness, and microtexture in Al-4.5wt%Cu-5wt%TiB2 in situ composite10.1007/s11837-016-1911-4 ↗
45. Modeling of continuous dynamic recrystallization of Al-Zn-Cu-Mg alloy during hot deformation based on the internal-state-variable (ISV) method10.1016/j.ijplas.2018.03.002 ↗
46. Anisotropic ductile fracture10.1016/j.actamat.2004.06.020 ↗
47. Ductile failure modeling10.1007/s10704-016-0142-6 ↗
48. A general physics-based hardening law for single phase metals10.1016/j.actamat.2022.117877 ↗
49. Relationship between strength and uniform elongation of metals based on an exponential hardening law10.1016/j.actamat.2022.117866 ↗