Location-dependent deformation behavior of additively manufactured copper and copper-carbon nanotube composite
Source abstract
Abstract
Pure copper (Cu) and copper-carbon nanotube (Cu-CNTs) alloys were fabricated using laser powder bed fusion additive manufacturing (LPBF-AM) with a relatively high density. Their location-dependent (i.e., distance from build plate) microstructure and nanomechanical properties at room temperature were investigated. The microstructure of the as-build Cu showed ~40% lower porosity as compared to the AM Cu-CNTs. The amount of porosity was dependent on location for Cu sample with the bottom surface had ~61% lower porosity as compared to the top surface, however the change in porosity was negligible for as-build Cu-CNTs depending on the distance from the build plate. With the addition of 0.5 wt% CNTs, the mechanical properties of the composite were decreased slightly may be due to porosity, weak interfacial bonding of Cu and CNTs, CNT agglomeration, and degraded CNTs. Nanoindentation tests showed that the average modulus value and hardness of the composites were in the range of 40–80 GPa and 0.7–1.1 GPa, respectively depending on the strain rates and distance from the build plate; 18% and 25% decreases were achieved compared with pure copper, respectively. Creep displacement also increased for as-build Cu-CNTs as compared to the pure Cu. Further, for each system, increase in porosity led to increase in strain rate sensitivity and decrease in maximum creep displacement.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Additive Manufacturing Materials and Processes · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (54)
Show source-provided references
1. Laser 3D printing of complex copper structures
2. Process development for the manufacturing of 99.94% pure copper via selective electron beam melting10.1016/j.matlet.2014.12.105 ↗
3. A review on additive manufacturing of pure copper10.3390/coatings11060740 ↗
4. Sundaram · 2018 · 5
5. Mechanical properties of carbon nanotube-copper nanocomposites10.1088/0960-1317/18/3/035013 ↗
6. L. Ladani, Multi-scale Manufacturing of Carbon Nanotube Composites, no. 1658254.109US0. pp. 1–19, 2016.
7. Cohesive zone model for the interface of multiwalled carbon nanotubes and copper: molecular dynamics simulation10.1115/1.4029462 ↗
8. Interfacial strength between single wall carbon nanotubes and copper material: molecular dynamics simulation10.1115/1.4026939 ↗
9. Mechanical integrity of a carbon nanotube/copper-based through-silicon via for 3D integrated circuits: a multi-scale modeling approach10.1088/0957-4484/26/48/485705 ↗
10. Fabrication of carbon nanotube/copper and carbon nanofiber/copper composites for microelectronics10.1016/j.mtcomm.2017.03.004 ↗
11. Size effects on microstructure and mechanical properties of additively manufactured copper–chromium–niobium alloy10.1016/j.msea.2021.141511 ↗
12. Microstructure and mechanical properties of additive manufactured copper alloy10.1016/j.matlet.2016.05.064 ↗
13. Review of powder bed fusion additive manufacturing for metals10.3390/met11091391 ↗
14. Local and global mechanical behavior and microstructure of Ti6Al4V parts built using electron beam melting technology10.1007/s11661-015-2965-6 ↗
15. L. Ladani, Additive Manufacturing of Metals: Materials, Processes, Tests, and Standards. DEStech Publications, Incorporated, 2020.
16. L. Awad,Ibrahim; Ladani, “No Title,” Proceedings of the ASME 2014 International Mechanical Engineering Congress and Exposition IMECE2014 November 14–20, 2014, Montreal, Quebec, Canada, 2014.
17. Temperature profile, bead geometry, and elemental evaporation in laser powder bed fusion additive manufacturing process10.1007/s11837-019-03872-3 ↗
18. Finite element simulation of laser additive melting and solidification of Inconel 718 with experimentally tested thermal properties10.1016/j.finel.2017.07.002 ↗
19. F. Ahsan, J. Razmi, L. Ladani, Multi-physics modeling of laser interaction with surface in powder bed melting process, ASME International Mechanical Engineering Congress and Exposition, Proceedings (IMECE), 2, no. November, 2018, doi: 10.1115/IMECE2018–86566.10.1115/IMECE2018-86566 ↗
20. Laser additive melting and solidification of inconel 718: finite element simulation and experiment10.1007/s11837-015-1765-1 ↗
21. Thermal modeling of laser based additive manufacturing processes within common materials10.1016/j.promfg.2015.09.012 ↗
22. Direct metal laser melting of Inconel 718: process impact on grain formation and orientation10.1016/j.jallcom.2017.11.130 ↗
23. Mechanical behavior of electron beam powder bed fusion additively manufactured Ti6Al4V parts at elevated temperatures10.1115/1.4049092 ↗
24. Mechanical anisotropy and strain rate dependency behavior of Ti6Al4V produced using E-beam additive fabrication10.1115/1.4027729 ↗
25. Effective liquid conductivity for improved simulation of thermal transport in laser beam melting powder bed technology
26. Optimizing quality of additively manufactured Inconel 718 using powder bed laser melting process
27. Temperature distribution and melt geometry in laser and electron-beam melting processes - a comparison among common materials
28. Mechanical anisotropy and surface roughness in additively manufactured parts fabricated by stereolithography (SLA) using statistical analysis
29. Microstructural and mechanical characterization of high-alloy quenching and partitioning TRIP steel manufactured by electron beam melting10.1016/j.msea.2020.139684 ↗
30. Tribo-corrosion response of additively manufactured high-entropy alloy10.1038/s41529-021-00177-2 ↗
31. Development and characterisation of direct laser sintering Cu-based metal powder10.1016/S0924-0136(03)00755-6 ↗
32. Metallurgical mechanisms in direct laser sintering of Cu-CuSn-CuP mixed powder10.1016/j.jallcom.2006.08.040 ↗
33. Direct laser sintering of a copper-based alloy for creating three-dimensional metal parts10.1016/S0924-0136(03)00766-0 ↗
34. Influence of selective laser melting process parameters on texture evolution in pure copper10.1016/j.jmatprotec.2019.02.022 ↗
35. Electrical resistivity of pure copper processed by medium-powered laser powder bed fusion additive manufacturing for use in electromagnetic applications
36. Mechanical and electrical properties of selective laser-melted parts produced from surface-oxidized copper powder
37. Mechanical properties and failure mechanisms at high temperature in carbon nanotube reinforced copper matrix nanolaminated composite10.1016/j.compositesa.2018.10.022 ↗
38. Strain rate sensitivity of a novel refractory high entropy alloy: Intrinsic versus extrinsic effects10.1016/j.msea.2019.138326 ↗
39. Small-scale mechanical behavior of a eutectic high entropy alloy10.1038/s41598-020-59513-2 ↗
40. Deformation and tribological behavior of ductile refractory high-entropy alloys
41. Strength, strain-rate sensitivity and ductility of copper with nanoscale twins10.1016/j.actamat.2006.06.062 ↗
42. Strain gradient plasticity in multiprincipal element alloys10.1007/s11837-019-03703-5 ↗
43. Micromechanics and indentation creep of magnesium carbon nanotube nanocomposites: 298 K–573 K10.1016/j.msea.2020.140418 ↗
44. W.D. Nix*$, H. Gao, Indentation Size Effects in Crystalline Materials: A Law for Strain Gradient Plasticity, 1998.10.1016/S0022-5096(97)00086-0 ↗
45. M. Li, S.J. Zinkle, 4.20 Physical and Mechanical Properties of Copper and Copper Alloys.
46. Effect of size and shape of metal particles to improve hardness and electrical properties of carbon nanotube reinforced copper and copper alloy composites10.1016/j.compscitech.2010.07.012 ↗
47. Tribological application of carbon nanotubes in a metal-based composite coating and composites10.1016/S0008-6223(02)00265-8 ↗
48. Laser additive manufacturing bulk graphene-copper nanocomposites10.1088/1361-6528/aa8946 ↗
49. Contact-damage-resistant ceramic/single-wall carbon nanotubes and ceramic/graphite composites10.1038/nmat1161 ↗
50. C.L. Xu, B.Q. Wei, R.Z. Ma, J. Liang, X.K. Ma, D.H. Wu, Fabrication of aluminum-carbon nanotube composites and their electrical properties, 1999.
51. Single-wall carbon nanotubes as attractive toughening agents in alumina-based nanocomposites10.1038/nmat793 ↗
52. Indentation strain rate sensitivity of ball-milled spark-plasma sintered Cu-C metal matrix composite10.1016/j.jallcom.2018.07.155 ↗
53. High-temperature nano-indentation creep behavior of multi-principal element alloys under static and dynamic loads10.3390/met10020250 ↗
54. Creep behaviour of SAC387 lead free solder alloy reinforced with single walled carbon nanotubes10.1007/s12666-014-0458-8 ↗