journal article·2018-05

Effects of Mo films prepared via different sputtering conditions on the formation of MoSe2 during selenization

Yong-Jian Liu, Chang-Ying Ou, Chung-Hsin Lu

Publisher page

Abstract

Abstract The effects of Mo films prepared via various sputtering conditions on the formation of MoSe2 during selenization were investigated. After selenization treatment, the morphology of Mo films changed from pyramidal-like grains to round grains due to the formation of MoSe2, and the sheet resistance increased. The sheet resistance of the selenized Mo films was increased with the increase in the selenization temperature because of the raised amount of formed MoSe2. As the sputtering power for preparing Mo films was increased from 100 W to 250 W, an increase in the grain size of Mo films was observed. The enlarged grains of Mo films resulted in a small amount of grain boundaries, thereby reducing the contact area between Mo films and selenium vapor during the selenization process. The conversion ratio of MoSe2 calculated according to the increase in the film thickness significantly decreased as the sputtering power was increased. It is indicated that increasing the sputtering power for preparing Mo films significantly reduced the reactivity of Mo films with selenium and suppressed the formation of MoSe2.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Chalcogenide Semiconductor Thin Films · Semiconductor materials and interfaces · Quantum Dots Synthesis And Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. Potassium-induced surface modification of Cu(In, Ga)Se2 thin films for high-efficiency solar cells10.1038/nmat3789 ↗
2. Effects of heavy alkali elements in Cu(In, Ga)Se2 solar cells with efficiencies up to 22.6%10.1002/pssr.201600199 ↗
3. BIPV: merging the photovoltaic with the construction industry10.1002/pip.920 ↗
4. A comprehensive characterization of the interfaces in Mo/CIS/CdS/ZnO solar cell structures10.1016/0927-0248(95)00107-7 ↗
5. Electronic level alignment at the deeply buried absorber/Mo interface in chalcopyrite-based thin film solar cells10.1063/1.2955532 ↗
6. Alternative back contact materials for thin film Cu(In, Ga)Se2 solar cells
7. Optimization of molybdenum thin films for electrodeposited CIGS solar cells10.1016/j.solmat.2010.12.011 ↗
8. Effect of dimethylaluminumhydride-derived aluminum oxynitride passivation layer on the interface chemistry and band alignment of HfTiO-InGaAs gate stacks10.1063/1.4808243 ↗
9. Interface control and modification of band alignment and electrical properties of HfTiO/GaAs gate stacks by nitrogen incorporation10.1039/C4TC00572D ↗
10. Microstructure optimization and optical and interfacial properties modulation of sputtering-derived HfO2 thin films by TiO2 incorporation10.1016/j.jallcom.2014.05.074 ↗
11. Modulating the interface quality and electrical properties of HfTiO/InGaAs gate stack by atomic-layer-deposition-derived Al2O3 passivation layer10.1021/am506351u ↗
12. Characterization of the Cu(In, Ga)Se2/Mo interface in CIGS solar cells10.1016/S0040-6090(00)01846-0 ↗
13. Electrical properties of the Cu(In, Ga)Se2/MoSe2/Mo structure10.1016/S0927-0248(00)00283-X ↗
14. Determining factor of MoSe2 formation in Cu(In, Ga)Se2 solar cells10.1016/j.solmat.2012.02.015 ↗
15. Effects of selenization conditions on densification of Cu(In, Ga)Se2 (CIGS) thin films prepared by spray deposition of CIGS nanoparticles10.1063/1.3141755 ↗
16. Optimization of MoSe2 formation for Cu(In, Ga)Se2-based solar cells by using thin superficial molybdenum oxide barrier layers10.1016/j.tsf.2013.07.038 ↗
17. Control of an interfacial MoSe2 layer in Cu2ZnSnSe4 thin film solar cells: 8.9% power conversion efficiency with a TiN diffusion barrier10.1063/1.4740276 ↗
18. Phase formation and ferroelectric characteristics of nonfatigue barium bismuth tantalate thin films10.1063/1.371695 ↗
19. Preparation and characterization of Cu(In, Ga)Se2 films from nanosized alloy precursors10.1007/s10854-014-1944-9 ↗
20. Structural and electrical properties of DC sputtered molybdenum films10.1016/S0927-0248(97)00236-5 ↗
21. Investigation of sputtered Mo layers on soda-lime glass substrates for CIGS solar cells10.1088/0268-1242/27/11/115020 ↗
22. Electrical and morphological properties of low resistivity Mo thin films prepared by magnetron sputtering10.1590/S0103-97332006000600049 ↗
23. High-pressure effect on MoS2 and MoSe2 single crystals grown by CVT method10.1007/BF02708507 ↗