journal article·2018-04

Investigation on the properties of nanostructured Cu alloy prepared by mechanical milling and reactive hot-pressing

Litao Han, Jianwei Liu, Huaguo Tang, Xianfeng Ma, Wei Zhao

Publisher page

Abstract

Abstract In this present research, the nanostructured Cu alloy was successfully prepared by mechanical milling (MM) and reactive hot-pressing (RHP). The effects of milling time and sintering temperature on density, microstructure, electrical conductivity and mechanical properties were investigated. The results indicated that the nanostructured Cu had a great influence on the properties of the alloys. The crystallite size of the alloy samples exhibited a minimum value of 12 nm after milling for 6 h (by XRD and TEM). Consequently, the greatly improved mechanical properties were accompanied with a little reduced electrical conductivity due to the grain refinement. The best mechanical properties were obtained by the specimen sintered at 600 °C and ball-milled for 5 h. It shows a better combination of electrical conductivity (71.86% IACS) and tensile strength (649 MPa) in spite of having a density 97.46% compared with the conventional copper and Cu-Fe alloy.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (21)

Show source-provided references
1. Copper and copper alloys
2. Suryanarayana · 2004
3. Enhanced mechanical properties of pure copper with a mixture microstructure of nanocrystalline and ultrafine grains10.1016/j.matlet.2016.09.020 ↗
4. Microstructure characteristic, mechanical properties and sintering mechanism of nanocrystalline copper obtained by SPS process10.1016/j.msea.2009.07.016 ↗
5. A maximum in the strength of nanocrystalline copper10.1126/science.1086636 ↗
6. A bulk of uniform nanocrystalline copper with superior comprehensive mechanical properties electroformed in an ultra-low sulfate concentration bath without additives10.1016/j.msea.2017.08.031 ↗
7. Mechanical alloying and milling10.1016/S0079-6425(99)00010-9 ↗
8. Simultaneous improvement in the strength and corrosion resistance of Al via high-energy ball milling and Cr alloying10.1016/j.matdes.2015.06.120 ↗
9. Processing of advanced materials using high-energy mechanical milling10.1016/S0079-6425(03)00034-3 ↗
10. Huang · 2006
11. Synthesis, sintering, and mechanical properties of nanocrystalline cemented tungsten carbide – a review10.1016/j.ijrmhm.2008.07.011 ↗
12. Mechanical properties and rapid consolidation of binderless nanostructured tantalum carbide10.1016/j.ceramint.2009.06.012 ↗
13. Consolidation of binderless nanostructured titanium carbide by high-frequency induction heated sintering10.1016/j.ceramint.2010.03.007 ↗
14. Rapid sintering of ultra fine WC and WC-Co hard materials by high-frequency induction heated sintering and their mechanical properties10.1007/BF03027821 ↗
15. Reactive hot pressing of ZrB2–SiC composites10.1111/j.1151-2916.2000.tb01558.x ↗
16. Reactive hot pressing of alumina-silicon carbide nanocomposites10.1111/j.1551-2916.2004.00299.x ↗
17. Low-temperature densification of zirconium diboride ceramics by reactive hot pressing10.1111/j.1551-2916.2006.01299.x ↗
18. Nanostructured WC/Co composite powder prepared by high energy ball milling10.1016/j.scriptamat.2003.08.009 ↗
19. Investigation into the sintered behavior and properties of nanostructured WC–Co–Ni–Fe hard metal alloys10.1016/j.msea.2014.03.096 ↗
20. Microstructure and mechanical properties of WC-Ni-Al based cemented carbides developed for engineering applications10.3139/146.110593 ↗
21. Characterization and properties of sintered WC–Co and WC–Ni–Fe hard metal alloys10.1016/j.jallcom.2013.09.188 ↗