The effect of rolling on the microstructure and compression behavior of AA5083 subjected to large-scale ECAE
Source abstract
Abstract
Abstract In the present work, an aluminum alloy AA5083 that went through equal channel angular extrusion (ECAE) was further processed with rolling under two different conditions. Mechanical examination on both as-ECAE and ECAE + Rolling samples suggests that such post-ECAE processes can further effectively enhance the strength of the alloy. The underlying mechanisms were investigated with the assistance of microstructural examination using transmission electron microscopy (TEM). Precipitates of two morphologies were found in the alloys with dimensions ranging from a few to hundreds of nanometers. These precipitates were determined to have a minor effect on the strength differences between the alloys with or without post-ECAE rolling. However, the work hardening caused by the high number of dislocations accumulated inside the grains and the concomitant grain size reduction along the normal direction (ND) due to plate thickness reduction were considered as the primary reasons for the strength increase in the post-ECAE rolled AA5083.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (39)
Show source-provided references
1. The deformation and ageing of mild steel: III. Discussion of results10.1088/0370-1301/64/9/303 ↗
2. The cleavage strength of polycrystals
3. Mechanical behavior and strengthening mechanisms in ultrafine grain precipitation-strengthened aluminum alloy10.1016/j.actamat.2013.09.042 ↗
4. Low-temperature superplastic behavior of a submicrometer-grained 5083 Al alloy fabricated by severe plastic deformation10.1007/s11661-002-0271-6 ↗
5. Grain refinement and superplasticity in an aluminum alloy processed by high-pressure torsion10.1016/j.msea.2004.11.007 ↗
6. Single layer and multilayer wear resistant coatings of (Ti,Al)N: a review10.1016/S0921-5093(02)00259-9 ↗
7. Plasma electrolysis for surface engineering10.1016/S0257-8972(99)00441-7 ↗
8. Protective coatings on magnesium and its alloys - a critical review10.1016/S0925-8388(01)01899-0 ↗
9. Manufacture, characterisation and application of cellular metals and metal foams10.1016/S0079-6425(00)00002-5 ↗
10. Softening of nanocrystalline metals at very small grain sizes10.1038/35328 ↗
11. Structural and thermodynamic properties of nanocrystalline fcc metals prepared by mechanical attrition10.1557/JMR.1992.1751 ↗
12. Particle reinforced aluminium and magnesium matrix composites10.1179/imr.1994.39.1.1 ↗
13. Creep and microstructure in ultrafine-grained 5083 Al10.1007/s10853-012-7115-6 ↗
14. On torsion combined with compression10.1063/1.1714987 ↗
15. The effect of hydrostatic pressure on plastic flow under shearing stress10.1063/1.1707772 ↗
16. Strength and ductility of ultrafine grained aluminum and iron produced by ARB and annealing10.1016/S1359-6462(02)00282-8 ↗
17. Microstructures and mechanical properties of 6061 aluminum alloy processed by accumulative roll-bonding10.1016/S0921-5093(01)01416-2 ↗
18. Strengthening mechanisms in nanostructured high-purity aluminium deformed to high strain and annealed10.1016/j.actamat.2009.05.017 ↗
19. Microstructural evolution and mechanical-properties of a forged gamma-titanium aluminide alloy10.1016/0956-7151(92)90411-7 ↗
20. Temperature effect on fine-grained structure formation in high-strength Al alloy 7475 during hot severe deformation10.1016/j.msea.2009.03.037 ↗
21. Microstructure and mechanical properties of multi-directionally forged Mg-Al-Zn alloy10.1016/j.scriptamat.2011.10.005 ↗
22. On the homogeneity of deformation by high pressure torsion10.1016/j.scriptamat.2004.04.025 ↗
23. Microstructure and mechanical properties of super-strong nanocrystalline tungsten processed by high-pressure torsion10.1016/j.actamat.2006.05.005 ↗
24. Extreme grain refinement by severe plastic deformation: a wealth of challenging science10.1016/j.actamat.2012.10.038 ↗
25. Equal channel angular extrusion: from macromechanics to structure formation10.1016/S0921-5093(99)00248-8 ↗
26. Materials processing by simple shear10.1016/0921-5093(95)09705-8 ↗
27. Principles of equal-channel angular pressing as a processing tool for grain refinement10.1016/j.pmatsci.2006.02.003 ↗
28. Grain structure and texture in aluminium alloy AA5083 after equal angular channel extrusion, warm rolling and subsequent annealing10.1179/026708310X12701095964360 ↗
29. Microstructure characterization in cryomilled Al 508310.1016/j.msea.2006.05.039 ↗
30. Precipitation behavior of the ß phase in Al-508310.1016/j.msea.2009.10.007 ↗
31. Microstructure-based modelling of isotropic and kinematic strain hardening in a precipitation-hardened aluminium alloy10.1016/j.actamat.2011.02.035 ↗
32. Microstructures in the 6060 aluminium alloy after various severe plastic deformation treatments10.1016/j.matchar.2011.01.009 ↗
33. Effect of second phase particles on grain refinement during equal-channel angular pressing of an Al–Mg–Mn alloy10.1016/j.actamat.2011.10.023 ↗
34. Engineering and commercialization of equal channel angular extrusion (ECAE)10.1016/S0921-5093(04)00934-7 ↗
35. An investigation of microstructure and grain-boundary evolution during ECA pressing of pure aluminum10.1007/s11661-002-0049-x ↗
36. The origin of non-uniform microstructure and its effects on the mechanical properties of a friction stir processed Al–Mg alloy10.1016/j.actamat.2009.07.065 ↗
37. Tabor · 1951
38. Physics and phenomenology of strain hardening: the FCC case10.1016/S0079-6425(02)00003-8 ↗
39. Revisiting the Considère criterion from the viewpoint of dislocation theory fundamentals10.1016/j.scriptamat.2013.12.009 ↗