A practical method to improve mechanical and electrical properties of ADS copper prepared by cold spray additive manufacturing through powder pretreatment
Source abstract
Abstract
To reduce the oxygen content on the surface of alumina dispersion-strengthened copper alloy powders, and improve properties of the deposits prepared by cold spray additive manufacturing, these powders were pretreated with hydrogen reduction treatment at 300 ℃ and 500 ℃, respectively. The microstructure and mechanical and electrical properties of the deposits before and after powder heat treatment were systematically researched. The results show that hydrogen reduction treatment can effectively reduce the oxide film on the surface of the alumina-dispersion-strengthened copper powder without changing the microstructure and mechanical properties of the powder. The alumina-dispersion-strengthened copper alloy deposit prepared from the as-received powder has obvious pores, and the tensile strength and electrical conductivity are 75 MPa and 38% IACS, while these deposits prepared from the powder treated at 300 ℃ and 500 ℃ present a dense microstructure. The tensile strengths and electrical conductivity are 202 MPa under 45% IACS and 245 MPa under 48% IACS, respectively. At the same time, the nano-Al 2O 3 particles are very stable under the heating and deformation conditions of adiabatic shearing by cold spraying, and the Al 2O 3 particles are not significantly broken during the severe plastic deformation caused by the high-speed impact of cold spraying, which enables the deposits to directly inherit the nano-dispersion strengthening structure of the powder. Therefore, it is effective to improve the mechanical and electrical properties of alumina dispersion-strengthened copper deposits by using hydrogen reduction pre-treatment to reduce the oxide film on the surfaces of the particles.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Advanced materials and composites · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (48)
Show source-provided references
1. Al2O3-dispersed Cu prepared by the combustion synthesized powder
2. Effect of creep annealing on the dimensional stability of dispersion strengthened copper alloy10.1016/j.jallcom.2021.161321 ↗
3. Effect of CeO2 nanoparticles on interface of Cu/Al2O3 ceramic clad composites10.3390/ma13051240 ↗
4. Microstructural refinement and performance improvement of Cu–36 wt% Zn alloy by Al2O3 nanoparticles coupling electromagnetic stirring10.1007/s12598-016-0723-6 ↗
5. Strength and electrical conductivity behavior of nanoparticles reaction on new alumina dispersion-strengthened copper alloy10.1016/j.jallcom.2019.05.271 ↗
6. Research progress on advanced rail materials for electromagnetic railgun technology10.1016/j.dt.2020.03.014 ↗
7. Microstructure and mechanical properties of mechanically alloyed ODS copper alloy for fusion material application10.1016/j.nme.2018.05.019 ↗
8. Research status and development trend of preparation technology of ceramic particle dispersion strengthened copper-matrix composites10.1016/j.jallcom.2020.156475 ↗
9. Microstructure development of Y–Ti–O dispersion strengthened Cu alloys fabricated by mechanical alloying10.1016/j.matchar.2022.111808 ↗
10. Metal additive manufacturing: a review10.1007/s11665-014-0958-z ↗
11. A review of topology optimization for additive manufacturing: status and challenges10.1016/j.cja.2020.09.020 ↗
12. Selective electron beam melting of oxide dispersion strengthened copper10.1002/adem.201800068 ↗
13. On the processability of copper components via powder-based additive manufacturing processes: potentials, challenges and feasible solutions10.1016/j.jmapro.2021.10.038 ↗
14. Solid-state additive manufacturing and repairing by cold spraying: a review10.1016/j.jmst.2017.09.015 ↗
15. Current implementation status of cold spray technology: a short review10.1007/s11666-022-01382-4 ↗
16. Improving deposition efficiency and inter-particle bonding of cold sprayed Cu through removing the surficial oxide scale of the feedstock powder10.1016/j.surfcoat.2020.126709 ↗
17. Effects of powder characteristics and mixing powders on cold sprayability and corrosion properties of tantalum coatings10.1016/j.surfcoat.2021.127763 ↗
18. Particle-based simulation of cold spray: influence of oxide layer on impact process
19. A numerical approach to study the oxide layer effect on adhesion in cold spray10.1007/s11666-021-01245-4 ↗
20. Elucidation of cold-spray deposition mechanism by auger electron spectroscopic evaluation of bonding interface oxide film10.1016/j.actamat.2018.09.041 ↗
21. Dynamic evolution of oxide scale on the surfaces of feed stock particles from cracking and segmenting to peel-off while cold spraying copper powder having a high oxygen content10.1016/j.jmst.2020.06.019 ↗
22. Bonding mechanism in cold gas spraying10.1016/S1359-6454(03)00274-X ↗
23. Computational analysis of the interfacial bonding between feed-powder particles and the substrate in the cold-gas dynamic-spray process10.1016/S0169-4332(03)00643-3 ↗
24. Adiabatic shear instability based mechanism for particles/substrate bonding in the cold-gas dynamic-spray process10.1016/j.matdes.2004.03.008 ↗
25. Cold spray deposition: significance of particle impact phenomena10.1016/j.ast.2005.03.005 ↗
26. Significant influence of particle surface oxidation on deposition efficiency, interface microstructure and adhesive strength of cold-sprayed copper coatings10.1016/j.apsusc.2010.03.008 ↗
27. Microstructural features and properties of high-hardness and heat-resistant dispersion strengthened copper by reaction milling10.1007/s11595-011-0334-x ↗
28. Characteristics of nano-alumina particles dispersion strengthened copper fabricated by reaction synthesis10.1016/S1875-5372(16)30095-9 ↗
29. Investigation on microstructure and properties of Cu-Al2O3 composites fabricated by a novel in-situ reactive synthesis10.1016/j.matdes.2015.12.018 ↗
30. Effect of process parameters and heat treatments on properties of cold sprayed copper coatings10.1007/s11666-007-9048-1 ↗
31. Literature review of metal additive manufacturing defects[M]. Gaithersburg, MD, USA: US Department of Commerce
32. Non-destructive characterization of additively manufactured components with x-ray computed tomography for part qualification: a study with laboratory and synchrotron x-rays10.1016/j.matchar.2021.110894 ↗
33. X-ray computed tomography for the ex-situ mechanical testing and simulation of additively manufactured IN718 samples
34. Investigation of pore structure in cobalt chrome additively manufactured parts using X-ray computed tomography and three-dimensional image analysis
35. Effect of hot isostatic pressing (HIP) on microstructure and mechanical properties of Ti6Al4V alloy fabricated by cold spray additive manufacturing
36. Unravelling the deposition mechanism of brittle particles in metal matrix composites fabricated via cold spray additive manufacturing10.1016/j.scriptamat.2020.10.055 ↗
37. Characterization of heat treatment-induced pore structure changes in cold-sprayed titanium10.1016/j.matchar.2017.08.006 ↗
38. Flow stress dependence on the grain size in alumina dispersion-strengthened copper with a bimodal grain size distribution10.1016/j.msea.2009.04.022 ↗
39. Hoganas A.B. , 2018. Sweden. Copper Alloy System with Unrivalled Performance https//www.hoganas.com/en/business-areas/glipcop (2018), Accessed 17th Apr 2018.
40. High temperature mechanical behavior of alumina dispersion strengthened copper alloy with high content of alumina10.1016/S1003-6326(15)63622-6 ↗
41. Microstructure and properties of Cu-0.4 wt% Al2O3 composites fabricated by hot extrusion and cold drawing10.1007/s11665-021-06247-5 ↗
42. Correlating particle impact condition with microstructure and properties of the cold-sprayed metallic deposits10.1016/j.jmst.2019.09.023 ↗
43. High pressure cold sprayed (HPCS) and low pressure cold sprayed (LPCS) coatings prepared from OFHC Cu feedstock: overview from powder characteristics to coating properties10.1007/s11666-012-9790-x ↗
44. Dependency of deposition behavior, microstructure and properties of cold sprayed Cu on morphology and porosity of the powder10.1016/j.surfcoat.2017.08.070 ↗
45. The influence of powder particle velocity and microstructure on the properties of cold sprayed copper coatings10.1007/s11666-011-9614-4 ↗
46. Pure copper components fabricated by cold spray (CS) and selective laser melting (SLM) technology10.1016/j.surfcoat.2020.125936 ↗
47. Copper-Al2O3 composites prepared by reactive spray deposition10.1016/0956-716X(94)90275-5 ↗
48. Effect of heat treatment on properties of cold sprayed nanocrystalline copper alumina coatings10.1016/j.actamat.2007.04.044 ↗