Effect of plasma spray FeCrAly coating on microstructural and mechanical properties of Ni61Cr22Mo9Fe5 - ER2209 nickel based alloy fabricated using wire arc additive manufacturing process
Source abstract
Abstract
In this current research, the Ni61Cr22Mo9Fe5 (NiCr) - ER2209 (FeCr) wire was proposed to produce a nickel based alloy materials utilising the wire arc additive manufacturing (WAAM) process. Wire arc additive manufacturing (WAAM) and wire arc additive manufacturing coated (WAAM-C) samples of two different types were created. In order to improve the WAAM sample`s mechanical strength and corrosion resistance, the outer surface layer was coated using the plasma spray FeCrAlY composite coating technique. The deposition of powder was kept as constant as 200 µm during plasma spray coating process. Microstructure analyses showed that the composite bonding sample had NiFe 2O 4 , Single phase nickel ferrite (SPNF), Ni-Co ferrite, α-phase, and Spinel ferrite structures. The metallic functional phase (MFP) of Ni61Cr22Mo9Fe5 - ER2209 wire was shaped utilizing additive manufacturing process, whilst homogeneous structure and NiCr structure were established collateral bonding in the base materials. Texture results of WAAM-C sample showed As 1 < 111 > , As 2 < 200 >, As 3 < 211 > and As 4 < 222 > cub structure at the outer surface. The hardness values of outer surface layers of WAAM-C have been continuously increased by 4 % compared to the WAAM sample. The hardness values of WAAM-C and WAAM were seen as 180 HV and 166 HV, respectively. The WAAM-C showed the elongation of 3 % and yield strength of 600 MPa. Further, the fracture morphology revealed that both the samples did not show dimples, void, crack and hole. WAAM-C materials achieved higher corrosion resistance and good surface finish. Further, potential dynamic investigations were conducted on both WAAM and WAAM-C samples.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · Additive Manufacturing and 3D Printing Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. Microstructure characterization and tensile properties of squeeze-cast AlSiMg alloys10.1016/j.matlet.2004.11.041 ↗
2. Hybrid manufacturing of components from Ti-6Al-4V by metal forming and wire-arc additive manufacturing10.1016/j.jmatprotec.2020.116689 ↗
3. Multi-layer ultrasonic imaging of as-built wire+Arc additive manufactured components
4. Microstructure and mechanical properties of high strength steel deposits obtained by Wire-Arc additive manufacturing10.1016/j.jmatprotec.2020.116759 ↗
5. Wire arc additive manufacturing of titanium aluminide alloys using two-wire TOP-TIG welding: processing, microstructures, and mechanical properties
6. Influence of severe double-shot peening and plasma spray arc TiAlCr/AlCrSi coating on tribological behaviour of pure aluminium alloy10.1007/s10904-022-02429-3 ↗
7. Wire arc additive manufacturing of Al-Zn-Mg-Cu alloy: microstructures and mechanical properties
8. Effect of post heat treatment on the microstructure and mechanical properties of wire-arc additively manufactured A357 alloy components10.1016/j.matlet.2020.127674 ↗
9. Interfacial bonding between a wire arc additive manufactured 420 martensitic stainless steel part and its wrought base plate10.1016/j.matchemphys.2020.123199 ↗
10. Microstructure and mechanical properties of wire arc additively manufactured AZ80M magnesium alloy10.1016/j.matlet.2019.03.063 ↗
11. Fluctuation effects in wire arc additive manufacturing of aluminium analysed by high-speed imaging10.1016/j.jmapro.2020.05.030 ↗
12. A hypoeutectic Al-Ni-Mg in situ composite processed by wire-arc additive manufacturing: phase evolution and mechanical behavior10.1016/j.matdes.2022.111066 ↗
13. Microstructures and mechanical properties of Al–Zn–Mg aluminium alloy samples produced by wire+ arc additive manufacturing10.1016/j.jmrt.2020.09.114 ↗
14. Residual stress distributions in thick specimens excavated from a large circular wire+ arc additive manufacturing mockup10.1016/j.jmapro.2020.05.007 ↗
15. Homogenization of microstructure and mechanical properties of wire arc additive manufactured martensitic stainless steel through optimization of post-process heat treatment10.1016/j.jmrt.2022.10.077 ↗
16. Laser opto-ultrasonic dual detection for simultaneous compositional, structural, and stress analyses for wire+ arc additive manufacturing
17. Microstructure, hardness and mechanical properties of two different unalloyed tantalum wires deposited via wire+ arc additive manufacture10.1016/j.ijrmhm.2019.104974 ↗
18. Microstructure characterization and tensile properties of CMT-based wire plus arc additive manufactured ER259410.1016/j.matchar.2020.110671 ↗
19. Welding and additive manufacturing with nanoparticle-enhanced aluminum 7075 wire10.1016/j.jallcom.2020.154987 ↗
20. Microstructure and mechanical properties of wire arc additively manufactured Hastelloy C276 alloy10.1016/j.matdes.2020.109007 ↗
21. Robot based wire arc additive manufacturing system with context-sensitive multivariate monitoring framework10.1016/j.promfg.2020.10.103 ↗
22. Influence of severe shot peening and Plasma spray FeCr18Ni10Mo3 coating on microstructure and mechanical properties of super austenite stainless steel sheets by laser beam welding10.1016/j.jmrt.2020.11.098 ↗
23. Influence of filler wires and high velocity oxygen fuel coating on the structural properties of Inconel 600 and Nickel alloy 800 HT dissimilar joints using autogenous cold metal transfer welding10.1088/2053-1591/ab31b0 ↗
24. Influence of ship-based vibration on characteristics of arc and droplet and morphology in wire arc additive manufacturing
25. Influence of plasma spray WCCrCNi coating and shot peening on surface properties and corrosion behavior of AZ31 Mg alloy10.1016/j.jmrt.2022.05.183 ↗
26. Effects of heat accumulation on the arc characteristics and metal transfer behavior in wire arc additive manufacturing of Ti6Al4V10.1016/j.jmatprotec.2017.07.037 ↗
27. Effects of heat accumulation on microstructure and mechanical properties of Ti6Al4V alloy deposited by wire arc additive manufacturing
28. Enhanced interface strength in steel-nickel bimetallic component fabricated using wire arc additive manufacturing with interweaving deposition strategy10.1016/j.jmst.2020.04.019 ↗
29. Zavdoveev, A., Klapatyuk, A., Baudin, T., MacDonald, E., G Mohan, D., Oliveira, J.P., Gajvoronskiy, A., Poznyakov, V., Kim, H.S., Brisset, F. and Khokhlov, M., Non-Equimolar Cantor High Entropy Alloy Fabrication Using Metal Powder Cored Wire Arc Additive Manufacturing.