Influence of SLM printing parameters and hot isostatic pressure treatment on the structure and properties of CuNi3Si1 alloy
Source abstract
Abstract
CuNi3Si1 is a precipitation-hardenable copper alloy exhibiting a favorable combination of high mechanical strength and electrical conductivity, sought after in the electrical and automotive industries. In this paper, a Selective Laser Melting process was applied to assess the effect of printing parameters on the structure and properties of this alloy. First, the acquired samples were investigated to determine their microstructure and optimize printing parameters. Furthermore, tensile testing, salt spray testing and potentiostatic measurements were carried out to estimate the application potential of the 3D-printed copper alloy. The samples printed using the optimal strategy with the highest volumetric energy density (laser power equal to 300 W and scanning speed to 500 mm/s) were characterized by high corrosion resistance in both printing directions (the vertical and horizontal one), the high tensile strength of 334±1 MPa and density of 8.798±0.001 g/cm 3 . On the other hand, applying the much lower volumetric energy density of 83 J/mm 3 results in the preparation of samples with a density of 8.689±0.002 g/cm 3 and tensile strength equal to 306±8 MPa. Finally, the possibility of applying Hot Isostatic Pressure technology as a designated post-processing treatment technology was described. It was confirmed that this method could increase the electrical conductivity of printed CuNi3Si1 alloy 4.7 times.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Additive Manufacturing Materials and Processes · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (49)
Show source-provided references
1. State-of-the-art of selective laser melting process: a comprehensive review10.1016/j.jmsy.2022.04.002 ↗
2. Materials characterization in-situ spherical TiB2/Cu composite powder: a new method of liquid phase reaction coupled with gas atomization10.1016/j.matchar.2022.112096 ↗
3. Study of pore defect and mechanical properties in selective laser melted Ti6Al4V alloy based on X-ray computed tomography10.1016/j.msea.2020.139981 ↗
4. Fatigue properties of Ti6Al4V cellular specimens fabricated via SLM: CAD vs real geometry10.1016/j.prostr.2017.11.068 ↗
5. Enhanced densification of copper during laser powder bed fusion through powder surface alloying10.1016/j.jmatprotec.2022.117575 ↗
6. Microstructures and electrical and mechanical properties of Cu-Cr alloys fabricated by selective laser melting10.1016/j.matdes.2019.107815 ↗
7. Mechanical properties and microstructural characterization of Cu-4.3 Pct Sn fabricated by selective laser melting10.1007/s11661-016-3779-x ↗
8. Manufacturing of pure copper with extraordinary strength-ductility-conductivity balance by cryorolling and annealing10.1016/j.cirpj.2022.03.010 ↗
9. Microstructure and mechanical properties of Cu-Ni-Si alloys10.1016/j.msea.2006.12.163 ↗
10. Characterization of aging properties and precipitation of copper base alloys10.1515/HTMP.2010.29.5-6.405 ↗
11. Atmospheric corrosion study in a harbor located in a tropical island10.1002/maco.201810161 ↗
12. Copper alloys
13. Corrosion resistance of Cu-Ni-Si alloy under high- temperature, high-pressure H2S and Cl- environments10.1007/s11665-018-3663-5 ↗
14. Enhanced hardness and moderate thermal conductivity of Cu-2.4Ni-0.7Si alloy processed via selective laser melting followed by suitable heat treatment10.2351/1.5127559 ↗
15. Selective laser melting of CuCrZr alloy: processing optimisation, microstructure and mechanical properties10.1016/j.jmrt.2022.06.158 ↗
16. High-strength silicon brass manufactured by selective laser melting10.1016/j.matlet.2017.09.011 ↗
17. Effective post processing of SLM fabricated Ti-6Al-4 V alloy: machining vs thermal treatment10.1016/j.jmapro.2021.06.035 ↗
18. Additive manufacturing of 24CrNiMo low alloy steel by selective laser melting: influence of volumetric energy density on densification, microstructure and hardness10.1016/j.msea.2021.140957 ↗
19. Synthesis and characterisation of advanced ball-milled Al-Al2O3 nanocomposites for selective laser melting10.1016/j.powtec.2016.04.015 ↗
20. Selective laser melting of graphene reinforced titanium matrix composites: Powder preparation and its formability10.1016/j.apt.2021.03.003 ↗
21. Selective laser melting of Cu–Cr–Zr copper alloy: parameter optimization, microstructure and mechanical properties
22. Additive manufacturing of high strength copper alloy with heterogeneous grain structure through laser powder bed fusion10.1016/j.actamat.2021.117311 ↗
23. The effect of aging on the microstructure of selective laser melted Cu-Ni-Si10.1007/s11661-017-4363-8 ↗
24. Overcoming the strength–ductility trade-off by tailoring grain-boundary metastable Si-containing phase in β-type titanium alloy
25. Achieving ultrahigh-strength in beta-type titanium alloy by controlling the melt pool mode in selective laser melting10.1016/j.msea.2021.141731 ↗
26. Circumventing the strength–ductility trade-off of β-type titanium alloys by defect engineering during laser powder bed fusion
27. Selective laser melting technology: from the single laser melted track stability to 3D parts of complex shape10.1016/j.phpro.2010.08.083 ↗
28. Microstructural and texture development in direct laser fabricated IN71810.1016/j.matchar.2013.12.012 ↗
29. Tuning the strength and ductility balance of a Co32Cr36Ni32 medium entropy alloy fabricated by selective laser melting: effect of segregations along grain boundaries10.1016/j.msea.2022.142923 ↗
30. Design materials based on simulation results of silicon induced segregation at AlSi10Mg interface fabricated by selective laser melting10.1016/j.jmst.2020.01.037 ↗
31. Elemental segregation in an AlCoCrFeNi high-entropy alloy – a comparison between selective laser melting and induction melting10.1016/j.jallcom.2018.12.267 ↗
32. Precipitate structure in a Cu-Ni-Si alloy10.1007/BF00356596 ↗
33. Use of bimodal particle size distribution in selective laser melting of 316L stainless steel
34. Comparative study of performance comparison of AlSi10Mg alloy prepared by selective laser melting and casting10.1016/j.jmst.2019.08.049 ↗
35. Mechanical, thermal, and corrosion properties of Cu-10Sn alloy prepared by laser-powder-bed-fusion additive manufacturing
36. Study of the corrosion properties in a hot forged Cu-Al-Ni alloy with added Cr10.1515/jmbm-2018-0016 ↗
37. Preparation and properties of 3D interconnected CNTs/Cu composites10.1515/ntrev-2020-0013 ↗
38. The anisotropic of corrosion and tribocorrosion behaviors of Ti–15Mo alloy fabricated by selective laser melting10.1016/j.matchar.2022.112000 ↗
39. On the effect of build orientation and residual stress on the corrosion of 316L stainless steel prepared by selective laser melting10.1016/j.corsci.2020.109149 ↗
40. Anisotropic corrosion behavior of Sc and Zr modified Al-Mg alloy produced by selective laser melting10.1016/j.corsci.2020.108657 ↗
41. EBSD investigation on the microstructure of Ti48Al2Cr2Nb alloy hot isostatic pressing formed by Selective laser melting (SLM10.1016/j.matlet.2021.131334 ↗
42. Effects of hot isostatic pressing treatment on the microstructure and tensile properties of Ni-based superalloy CM247LC manufactured by selective laser melting10.1016/j.msea.2022.143083 ↗
43. Effect of hot isostatic pressing on the microstructure and mechanical properties of 17-4PH stainless steel parts fabricated by selective laser melting10.1016/j.msea.2021.141035 ↗
44. Fundamental aspects of hot isostatic pressing: an overview10.1007/s11661-000-0078-2 ↗
45. Additive manufacturing – a review of hot deformation behavior and constitutive modeling of flow stress10.1016/j.cossms.2022.100992 ↗
46. Hot deformation processing of shape memory alloys: a review of effects on plastic flow behaviour, deformation mechanisms, and functional characteristics10.1016/j.aej.2022.06.055 ↗
47. Effects of fabrication parameters and post-processing treatments on the mechanical and tribological behavior of surface-enhanced copper based materials by selective laser melting10.1016/j.jmatprotec.2022.117564 ↗
48. Preparation of Cu–Cr–Zr alloy by selective laser melting: Role of scanning parameters on densification, microstructure and mechanical properties10.1016/j.msea.2022.142740 ↗
49. Thermal effect on the microstructure of the lattice structure Cu-10Sn alloy fabricated through selective laser melting10.1016/j.jallcom.2019.02.196 ↗