journal article·2023-06

Forming mechanism of growth twins and microstructure evolution on improvement of strength and toughness properties by β-eutectoid element in Ti-7Mo-4Al-4Zr-3Nb-2Cr-xFe alloys

Yili Li, Hongze Fang, Xiaofu Zhang, Shichen Sun, Ruirun Chen, Xiang Xue, Jingjie Guo

Publisher page

Abstract

To form growth twins and simultaneously improve strength and toughness by using a β-eutectoid element, Ti-7Mo-4Al-4Zr-3Nb-2Cr- x Fe alloys were prepared. The phase composition, morphology of growth twins, tensile properties and fracture toughness were tested. Also, the formation of growth twins and the strength-toughness mechanism were studied. The results show that α and β phases exist after heat treatment. The relative content of β phase increases from 6.1 % to 12.5 % with increasing Fe content. Dislocation entanglements and dislocation walls appear at the α/β interface. There are two kinds of α phases, which are α p and α s phases. The growth twin with a width of ∼20 nm is found in α s phase due to the mismatch with the matrix lattice during solidification process. The smallest size of α p phase is at 1.0 wt% Fe. As the stable element of the β phase, Fe increases the phase transformation resistance from β phase to α phase to limit the growth of α phase. When Fe content increases from 0 to 1.5 wt%, tensile strength increases from 1107 to 1314 MPa. By increasing Fe content from 0 to 1.0 wt%, fracture toughness and elongation increase from 64 to 80 MPa·m 1/2 and 5.4–7.1 %, respectively. The strength and toughness of the alloys increase simultaneously within 0–1.0 wt%Fe. The solution strengthening of Fe, the refinement of α p phase, and the formation of growth twins and dislocation walls are the main reasons for the improvement in strength and toughness.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Intermetallics and Advanced Alloy Properties · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (62)

Show source-provided references
1. Influence of annealing on the microstructure and Charpy impact toughness of wire arc additive manufactured Ti5111 alloy10.1016/j.msea.2022.144255 ↗
2. Multi-phase trajectory optimization of aerospace vehicle using sequential penalized convex relaxation10.1016/j.ast.2021.107175 ↗
3. High strength and toughness of Ti-6Al-4V sheets via cryorolling and short-period annealing10.1016/j.msea.2022.143766 ↗
4. Fracture toughness of a rejuvenated β-Ti reinforced bulk metallic glass matrix composite10.1016/j.jmst.2021.09.001 ↗
5. Microstructure tailoring and impact toughness of a newly developed high strength Ti-5Al-3Mo-3V–2Cr-2Zr-1Nb-1Fe alloy10.1016/j.matchar.2021.111103 ↗
6. Oxygen-gradient titanium with high strength, strain hardening and toughness10.1016/j.actamat.2023.118674 ↗
7. Microstructure evolution and mechanical properties of directionally solidified large size Ti-47Al-5Nb-0.18C-0.3Si alloy by electromagnetic confinement10.1016/j.jallcom.2021.161762 ↗
8. Design of high strength and wear-resistance β-Ti alloy via oxygen-charging10.1016/j.actamat.2022.117686 ↗
9. Effect of silicon addition on microstructure and mechanical properties of a high strength Ti-4Al-4Mo-4Sn alloy prepared by powder metallurgy10.1016/j.jallcom.2021.162267 ↗
10. High dislocation density-induced large ductility in deformed and partitioned steels10.1126/science.aan0177 ↗
11. Controlling the microstructure and fracture toughness of the Ti-5Al-5Mo-5V–1Cr-1Fe alloy by multiple heat treatments10.1016/j.jmrt.2022.02.020 ↗
12. Development of beta-type Ti-Nb-Zr-Mo alloys for orthopedic applications
13. Deformation mechanism of bimodal microstructure in Ti-6Al-4V alloy: the effects of intercritical annealing temperature and constituent hardness10.1016/j.jmst.2020.08.057 ↗
14. Yielding nature and Hall-Petch relationships in Ti-6Al-4V alloy with fully equiaxed and bimodal microstructures10.1016/j.scriptamat.2019.07.015 ↗
15. Double toughening Ti-based bulk metallic glass composite with high toughness, strength and tensile ductility via phase engineering
16. Microstructural strengthening and toughening mechanisms in Fe-containing Ti-6Al-4V: a comparison between homogenization and aging treated states10.1016/j.jmst.2021.04.063 ↗
17. Toughening effects of Mo and Nb addition on impact toughness and crack resistance of titanium alloys10.1016/j.jmst.2020.11.045 ↗
18. Exploring the elastic, mechanical and anisotropic response of Ti-5Al-XSn alloys through DFT calculations10.1016/j.cjph.2022.02.016 ↗
19. Microstructure evolution and deformation mechanism of α+β dual-phase Ti-xNb-yTa-2Zr alloys with high performance10.1016/j.jmst.2022.04.052 ↗
20. Enhanced strength-ductility synergy in fiber-like structural titanium matrix composites by controlling TiB content10.1016/j.jallcom.2022.165399 ↗
21. Corrosion behavior of dual-phase Ti-6Al-4V alloys: A discussion on the impact of Fe content10.1016/j.jallcom.2020.157708 ↗
22. Effect of Fe content on microstructure and hardness of Ti-4.5Mo-5Al-1.8Zr-2.5Cr-1.1Sn titanium alloy based on high-throughput diffusion couple10.1016/j.msea.2022.143089 ↗
23. Improved mechanical, bio-corrosion properties and in vitro cell responses of Ti-Fe alloys as candidate dental implants10.1016/j.msec.2021.111917 ↗
24. Phase decomposition upon heat-treatment of a eutectoid Ti-Fe alloy processed by dual-wire-arc additive manufacturing10.1016/j.matlet.2022.132305 ↗
25. Influence of Fe on the microstructure, superplasticity and room-temperature mechanical properties of Ti-4Al-3Mo-1V-0.1B alloy10.1016/j.msea.2022.143245 ↗
26. On the influence of the heat treatment on microstructure formation and mechanical properties of near-α Ti-Fe alloys
27. Corrosion behavior of dual-phase Ti-6Al-4V alloys: a discussion on the impact of Fe content10.1016/j.jallcom.2020.157708 ↗
28. Development of Ti-Mo-Fe alloys combining different plastic deformation mechanisms for improved strength-ductility trade-off and high work hardening rate
29. Refinement of αs phase and formation of nano-twins of Ti-7Mo-4Al-3Nb-2Cr alloyed by Zr element10.1016/j.jmrt.2022.10.129 ↗
30. Unravelling the competitive effect of microstructural features on the fracture toughness and tensile properties of near beta titanium alloys10.1016/j.jmst.2021.04.032 ↗
31. A review of microstructure and texture evolution during plastic deformation and heat treatment of β-Ti alloys10.1016/j.jallcom.2021.163242 ↗
32. Plane strain fracture behavior of a new high strength Ti-5Al-3Mo-3V–2Zr-2Cr-1Nb-1Fe alloy during heat treatment10.1016/j.msea.2020.140080 ↗
33. Strength and fracture toughness of TC21 alloy with multi-level lamellar microstructure10.1016/j.msea.2018.10.056 ↗
34. The effect of surface oxidation behavior on the fracture toughness of Ti-5Al-5Mo-5V–1Cr-1Fe titanium alloy10.1016/j.jallcom.2015.05.211 ↗
35. Effect of electroshocking treatment on the microstructure and mechanical properties of laser melting deposited near-β Ti-55531 thin-wall10.1016/j.jallcom.2022.168187 ↗
36. Fracture toughness anisotropy of Ti17 billet processed by the β forging10.1016/j.msea.2021.140825 ↗
37. The interdependence of microstructure, strength and fracture toughness in a novel β titanium alloy Ti-5Al-4Zr-8Mo-7V10.1016/j.msea.2020.139248 ↗
38. The relationship between flow behavior and initial microstructure of Ti-10V–2Fe-3Al alloy during subtransus deformation10.1016/j.jallcom.2022.166302 ↗
39. Effect of heat treatments on microstructure and property of a high strength/toughness Ti-8V-1.5Mo-2Fe-3Al alloy10.1016/j.msea.2014.08.025 ↗
40. Generalized stacking fault energies and critical resolved shear stresses of random α-Ti-Al alloys from first-principles calculations10.1016/j.jallcom.2020.156314 ↗
41. Deformation-induced γ↔α2 phase transformation in TiAl alloy compressed at room temperature10.1016/j.intermet.2006.10.016 ↗
42. Stacking faults observed in {1012̅} extension twins in a compressed high Sn content Zr alloy10.1016/j.scriptamat.2017.07.028 ↗
43. Balancing strength and ductility by controllable heat-treatment twinning in a near β-Ti alloy10.1016/j.jmrt.2020.04.045 ↗
44. Additive manufacturing of TTFNZ (Ti-4.5Ta-4Fe-7.5Nb-6Zr), a novel metastable β-titanium alloy for advanced engineering applications10.1016/j.jallcom.2022.165899 ↗
45. In-situ investigation of plasticity in a Ti-Al-V-Fe (α+β) alloy: slip mechanisms, strain localization, and partitioning10.1016/j.ijplas.2021.103131 ↗
46. The effect of Si additions on the sintering and sintered microstructure and mechanical properties of Ti-3Ni alloy10.1016/j.msea.2011.06.029 ↗
47. The effects of Fe content on the microstructural evolution and tensile properties in Ti-6Al-4V-(2, 4)Fe alloys fabricated by thermomechanical powder consolidation10.1016/j.msea.2021.141877 ↗
48. Additive manufacturing of ultrafine-grained high-strength titanium alloys10.1038/s41586-019-1783-1 ↗
49. Surface nanocrystallization of body-centered cubic beta phase in Ti-6Al-4V alloy subjected to ultrasonic surface rolling process10.1016/j.surfcoat.2019.01.045 ↗
50. Modelling strengthening mechanisms in beta-type Ti alloys10.1016/j.msea.2019.04.027 ↗
51. Effect of grain size and temperature on the yield stress of the intermetallic compound TiAl10.1016/0036-9748(89)90434-1 ↗
52. Yielding nature and Hall-Petch relationships in Ti-6Al-4V alloy with fully equiaxed and bimodal microstructures10.1016/j.scriptamat.2019.07.015 ↗
53. Fracture characteristics analysis related to the microstructures in titanium alloys10.1016/0921-5093(96)10239-2 ↗
54. Multistage work hardening assisted by multi-type twinning in ultra-fine-grained heterostructural eutectic high-entropy alloys10.1016/j.mattod.2020.09.029 ↗
55. An X-ray method for the determination of stored energies in texture components of deformed metals; application to cold worked ultra high purity iron10.1016/S1359-6454(99)00457-7 ↗
56. A precipitation-hardened high-entropy alloy with outstanding tensile properties10.1016/j.actamat.2015.08.076 ↗
57. Microstructural evolution and strain-hardening in TWIP Ti alloys10.1016/j.actamat.2019.11.009 ↗
58. Mechanical properties and deformation mechanisms of Ti-15Nb-5Zr-4Sn-1Fe alloy with varying α phase fraction
59. Novel transformation pathway and heterogeneous precipitate microstructure in Ti-alloys10.1016/j.actamat.2020.06.048 ↗
60. Precipitation strengthening at ambient and elevated temperatures of heat-treatable Al(Sc) alloys10.1016/S1359-6454(02)00201-X ↗
61. Tensile properties of copper with nano-scale twins10.1016/j.scriptamat.2005.01.033 ↗
62. Dislocation nucleation governed softening and maximum strength in nano-twinned metals10.1038/nature08929 ↗