journal article·2023-05

Investigation on the spallation properties and failure mechanism of selective laser melted Ti-6Al-4V alloy with heat treatment under shock load

Jinhui Meng, Yang Liu, Zhiguo Li, Zhenyang Jiao, Yonggang Wang

Publisher page

Abstract

In this study, the effect of heat treatment on the microstructure of selective laser-melted Ti-6Al-4V alloy and the corresponding spalling performances and damage mechanism at ultra-high-speed (UHS) of 730 m/s are studied. Results show that the acicular martensite in the as-built sample is transformed into large grain basket-weave and Widmanstatten structures with solution treatment at 950 ℃ and 1050 ℃, respectively. The spallation damage mechanism is characterized by the aspects of grain refinement ratio (GRR) and damage porosity (DP). The HT-1050 sample has the highest GRR and DP, while the HT-950 sample has the lowest values, indicating that the HT-950 sample has the highest resistance of spallation. Due to the difference in microstructure morphology and grain size of the three samples, the spalling damage mode of the original sample is characterized by brittle fracture, and then it changes to pore growth and coalescence after heat treatment, larger grains have strong guiding effects on the coalescence of pores. The coalescence of the pores is always accompanied by dynamic recrystallization, thus reducing the local dislocation density and optimizing the development path of cracks. Based on the above work, can provide theoretical support for promoting the application of additive manufacturing alloys in defense industry and aerospace fields.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Laser-induced spectroscopy and plasma · High-Velocity Impact and Material Behavior

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (39)

Show source-provided references
1. Additive manufacturing of strong and ductile Ti-6Al-4V by selective laser melting via in situ martensite decomposition10.1016/j.actamat.2014.11.028 ↗
2. High strain rate mechanical behavior of Ti-6Al-4V octet lattice structures additively manufactured by selective laser melting (SLM)10.1016/j.msea.2018.12.101 ↗
3. Effect of geometry on the mechanical properties of Ti-6Al-4V Gyroid structures fabricated via SLM: a numerical study10.1016/j.matdes.2019.108165 ↗
4. In situ design of advanced titanium alloy with concentration modulations by additive manufacturing10.1126/science.abj3770 ↗
5. Influence of process parameter and strain rate on the dynamic compressive properties of selective laser-melted Ti-6Al-4V alloy10.1007/s00339-018-2359-x ↗
6. Selective laser manufacturing of Ti-based alloys and composites: impact of process parameters, application trends, and future prospects
7. Effect of porosity on dynamic response of additive manufacturing Ti-6Al-4V alloys10.3390/mi13030408 ↗
8. Discussion on the physical meaning of free surface velocity curve in ductile spallation10.7498/aps.64.034601 ↗
9. Micro-damage characteristics of incipient spall in high-purity copper
10. Effect of aging state on shock induced spall behavior of ultrahigh strength Al–Zn–Mg–Cu alloy10.1016/j.ijimpeng.2020.103725 ↗
11. A criterion for the time dependence of dynamic fracture10.1007/BF00186808 ↗
12. Dynamic response of AlSi10Mg alloy fabricated by selective laser melting10.1016/j.msea.2017.02.004 ↗
13. Characterization of bulk to thin wall mechanical response transition in powder bed AM
14. Spall fracture in additive manufactured Ti-6Al-4V10.1063/1.4963279 ↗
15. Failure mechanisms in ballistic performance of Ti-6Al-4V targets having equiaxed and lamellar microstructures10.1016/j.ijimpeng.2015.06.017 ↗
16. J.L. Wise, D.P. Adams, E.E. Nishida, B. Song, M.C. Maguire, J. Carroll, B. Reedlunn, J.E. Bishop, T.A. Palmer, Comparative shock response of additively manufactured versus conventionally wrought 304L stainless steel, AIP Conf. Proc., vol. 1793, 2017, 100015. 〈https://doi.org/10.1063/1.4971640〉.10.1063/1.4971640 ↗
17. Method of determining parameters of void growth damage model and its application to simulation of spall test
18. Tensile mechanical behavior and spall response of a selective laser melted 17-4 PH stainless steel10.1007/s11661-021-06229-1 ↗
19. Dynamic tensile mechanical response and spalling failure of GP1 stainless steel by laser selective melting additive manufacturing
20. Influence of shock-wave profile shape (triangulai-“Taylor-wave" versus square-topped) on the spallation response of 316L stainless steel
21. The role of lattice defects, element partitioning and intrinsic heat effects on the microstructure in selective laser melted Ti-6Al-4V10.1016/j.actamat.2019.01.039 ↗
22. Heat treatment of Ti6Al4V produced by selective laser melting: microstructure and mechanical properties10.1016/j.jallcom.2012.07.022 ↗
23. Effect of heating treatment on the microstructural evolution and dynamic tensile properties of Ti-6Al-4V alloy produced by selective laser melting10.1016/j.jmapro.2021.12.035 ↗
24. Deposition of Ti-6Al-4V using a high power diode laser and wire, Part I: investigation on the process characteristics10.1016/j.surfcoat.2008.02.008 ↗
25. A comparative study of mechanical properties and machinability of wrought and additive manufactured (selective laser melting) titanium alloy – Ti-6Al-4V10.1108/RPJ-08-2015-0105 ↗
26. Heat-treatment effects on mechanical properties and microstructure evolution of Ti-6Al-4V alloy fabricated by laser powder bed fusion10.1016/j.jallcom.2019.152615 ↗
27. Introduction of ternary alloying element in wire arc additive manufacturing of titanium aluminide intermetallic
28. The effect of heat treatment on microstructure evolution and tensile properties of selective laser melted Ti6Al4V alloy10.1016/j.jallcom.2018.12.051 ↗
29. Effect of heat treatment on microstructure evolution and mechanical properties of selective laser melted Ti–6Al–4V and TiB/Ti–6Al–4V composite: a comparative study10.1016/j.msea.2020.140415 ↗
30. A new insight of the relationship between crystallographic orientation and micro-cracks of Ti-47Al-2Cr-2 Nb alloy10.1016/j.msea.2018.06.053 ↗
31. Influence of void convergence on damage evolution of ductile metal spalling under strong dynamic loading
32. Developing a quantitative and predictive understanding
33. Effects of lamellar a thickness on dynamic mechanical properties and sensitivity to adiabatic shear banding of TC21 alloy
34. Damage evolution and spall failure in copper under complex shockwave loading conditions10.1063/5.0009521 ↗
35. A study of the heterogeneity of plastic deformation in IF steel by EBSD10.1016/j.msea.2012.03.068 ↗
36. Microstructure evolution and grain refinement behavior during hot deformation of Fe micro-alloyed Ti-6Al-4V10.1016/j.jmrt.2021.09.009 ↗
37. Dynamic compressive properties and underlying failure mechanisms of selective laser melted Ti-6Al-4V alloy under high temperature and strain rate conditions
38. Phase transitions in additively manufactured high-entropy alloy Cr10Mn10Fe60Co10Ni10 induced by high strain rate compression10.1016/j.scriptamat.2022.114955 ↗
39. Effects of Zr and Si addition on high-temperature mechanical properties and microstructure in Ti-10Al-2Nb-based alloys10.1016/j.msea.2019.04.031 ↗