Study on the preparation mechanism of novel WC-Cr2(C, N)-Co nanocomposites
Source abstract
Abstract
In this work, the WC-Cr 2 (C, N)-Co nanocomposites were synthesized by using the one-pot carbothermal reduction nitridation hydrothermal precursor method. The preparation mechanisms, including phase and morphology evolutions, were investigated by differential thermal analysis (TG-DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and thermodynamic analysis. The results showed that phase evolution, with temperature increasing, follows the sequences of (amorphous phase, WO 2.72) → (CoWO 4, WO 2.72, WO 2, CrWO 3) → (WO 2, CoWO 4, Co 6W 6C, CrWO 3) → (W 2C, Co 3W 3C, WC) → (WC, W 2C, Co 3W 3C) → (WC, Co, Co 3W 3 C trace amount). Through comparing different heat treatment conditions, the powder particle size was more easily affected by temperature than holding time. The higher temperatures or longer time holding resulted in the aggregation of powder particles. Finally, WC-Cr 2 (C, N)-Co nanopowders with about 60 nm were obtained at 1050 °C for 1 h under the N 2 flow of 1 L/min with the oxygen content of 0.22 wt% and the free carbon content of 0.19 wt%. The TEM elements mapping revealed that Cr distributes uniformly with WC grains, Co and WC grains are combined well. The surface of WC-Cr 2 (C, N)-Co determined by XPS is mainly composed of W, Co, Cr, C, N, and O. The spark plasma sintering (SPS) sintered WC-Cr 2 (C, N)-Co composite shows a nanocrystalline microstructure with the average grain size ∼170 nm, and the excellent comprehensive mechanical properties with the Vickers hardness 1730 Kg·mm −2 and fracture toughness 11.5 MPa·m 1/2, respectively.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · Advanced ceramic materials synthesis · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (43)
Show source-provided references
1. A comprehensive review on synergy effect between corrosion and wear of cemented tungsten carbide tool bits: a mechanistic approach10.1016/j.ijrmhm.2020.105315 ↗
2. A review of cemented carbides for rock drilling: an old but still tough challenge in geo-engineering10.1016/j.ijrmhm.2013.01.003 ↗
3. A critical comparison of the tribocorrosive performance in highly-alkaline wet medium of ultrafine-grained WC cemented carbides with Co, Co+Ni, or Co+Ni+Cr binders10.1016/j.ijrmhm.2020.105452 ↗
4. Reinforcement of tungsten carbide grains by nanoprecipitates in cemented carbides10.1088/0957-4484/27/41/415710 ↗
5. Orientation relationship in WC-Co composite nanoparticles synthesized by in situ reactions10.1088/0957-4484/26/14/145705 ↗
6. In-situ synthesis of WC-Co composite powder and densification by sinter-HIP10.1016/j.ijrmhm.2010.04.002 ↗
7. Vacuum sintering of WC-8 wt% Co hardmetals from WC powders with different dispersity10.1016/j.ijrmhm.2010.10.010 ↗
8. Properties and microstructure of VC/Cr3C2-doped WC/Co cemented carbides10.1016/S1001-0521(08)60011-X ↗
9. Fabrication of WC-8wt%Co hard materials by two rapid sintering processes10.1016/j.ijrmhm.2006.09.001 ↗
10. WC-TiC-Ni cemented carbide with enhanced properties10.1016/j.jallcom.2007.10.132 ↗
11. Nanostructured WC/Co composite powder prepared by high energy ball milling10.1016/j.scriptamat.2003.08.009 ↗
12. Preparation of ultrafine WC-Co composite powder by in situ reduction and carbonization reactions10.1016/j.ijrmhm.2008.05.001 ↗
13. Ultrafine hardmetals prepared by WC–10 wt%Co composite powder10.1016/j.ijrmhm.2007.04.004 ↗
14. Synthesis, sintering, and mechanical properties of nanocrystalline cemented tungsten carbide – a review10.1016/j.ijrmhm.2008.07.011 ↗
15. Enhancement of the mechanical properties of ultrafine-grained WC-Co cemented carbides via the in-situ generation of VC10.1016/j.jallcom.2022.163961 ↗
16. Tungsten carbide (WC) nanopowders synthesized via novel core–shell structured precursors10.1016/j.ceramint.2012.09.061 ↗
17. A facile route to synthesize WC-Co nanocomposite powders and properties of sintered bulk10.1016/j.jallcom.2016.03.285 ↗
18. Synthesis and characterization of WC-VC-Co nanocomposite powders through thermal-processing of a core-shell precursor10.1016/j.ceramint.2013.05.092 ↗
19. Fabrication of tungsten carbide–vanadium carbide core–shell structure powders and their application as an inhibitor for the sintering of cemented carbides10.1016/j.scriptamat.2012.07.043 ↗
20. Microstructural study on the grain growth inhibition of VC-doped WC-Co cemented carbides10.1016/j.ijrmhm.2016.06.009 ↗
21. Preparation and properties of the VC/Cr3C2/TaC doped ultrafine WC-Co tool material by spark plasma sintering
22. High resolution microscopy study in Cr3C2-doped WC-Co10.1023/A:1017953701641 ↗
23. Sintering behavior and mechanical properties of Cr3C2 doped ultra-fine WC-Co cemented carbides: experment guided with thermodynamic calculations10.1016/j.ijrmhm.2018.09.014 ↗
24. Effect of Mo and Co additions on the microstructure and properties of WC-TiC-Ni cemented carbides10.1016/j.ijrmhm.2011.07.011 ↗
25. A low temperature synthesized NbC as grain growth inhibitor for WC-Co composites10.1016/S0921-5093(00)00993-X ↗
26. The temperature ranges for maximum effectiveness of grain growth inhibitors in WC–Co alloys10.1016/j.ijrmhm.2005.05.011 ↗
27. General aspects and limits of conventional ultrafine WC powder manufacture and hard metal production10.1016/0263-4368(95)92674-9 ↗
28. Grain and phase boundary segregation in WC–Co with small V, Cr or Mn additions10.1016/j.actamat.2010.03.038 ↗
29. Influence and function of inhibitor VC/Cr3C2 on the grain growth in super fine WC-Co cermets
30. Effect of (Cr0.8V0.2)2(C, N) addition on microstructure and mechanical properties of WC-8Co cemented carbides10.1016/j.ijrmhm.2014.07.012 ↗
31. The enhancement of the microstructure and mechanical performances of ultrafine WC-Co cemented carbides by optimizing Cr2(C, N) addition and WC particle sizes10.1016/j.ijrmhm.2021.105518 ↗
32. Microstructure and mechanical properties improvements in cemented carbides by (Cr,Mo,Ta)2(C,N) inhibitors10.1007/s12598-019-01343-x ↗
33. Effect of Cu on the microstructures and properties of WC-6Co cemented carbides fabricated by SPS10.1016/j.ijrmhm.2016.06.007 ↗
34. Synthesis of tungsten oxide nanoparticles by acid precipitation method10.1016/j.ceramint.2006.02.007 ↗
35. Synthesis of (Cr,V)2(C, N) solid solution powders by thermal processing precursors10.1016/j.matchemphys.2017.02.025 ↗
36. Synthesis, characterization, and consolidation of Cr2(C, N) solid solution powders10.1111/jace.14215 ↗
37. Effect of a slight change in carbon content near the upper/lower limit on the microstructure and mechanical properties of WC-10Co cemented carbides10.1016/j.ijrmhm.2020.105465 ↗
38. Phase evolution in the synthesis of WC–Co–Cr3C2–VC nanocomposite powders from precursors10.1016/j.ijrmhm.2013.03.007 ↗
39. Synthesis of WC-0.67wt%Cr3C2 nanopowders by a one-step reduction-carbonization method and their characterization10.1016/j.ceramint.2022.03.234 ↗
40. Complexions in WC-Co cemented carbides10.1016/j.actamat.2018.02.018 ↗
41. Effect of rapid cooling on microstructure and properties of nanocrystalline WC-9%Co-Cr3C2-VC cemented carbide10.1016/j.ijrmhm.2022.105961 ↗
42. Effects of VC/Cr3C2 on WC grain morphologies and mechanical properties of WC-6wt%Co cemented carbides10.1016/j.jallcom.2017.04.187 ↗
43. Effects of processing parameters on the microstructure and mechanical properties of nanoscaled WC-10Co cemented carbide10.3390/ma15134472 ↗