Good combination of strength and mechanical isotropy in AA6082 alloy processed by high temperature intermediate annealing
Source abstract
Abstract
The microstructure, textures and mechanical property anisotropy of AA6082 alloy sheets after intermediate annealing were investigated. The result shows that the anisotropy of final cold-rolled and T6 alloy sheets decrease and the strengths increase as the intermediate annealing temperatures rise from 400 °C to 550 °C. Higher intermediate annealing temperature promotes the coarsening of soluble Mg 2Si particles, which influences subsequent recrystallization and precipitation. The final cold-rolled sheet intermediately annealed at 550 °C presents weak rolling textures, thereby decreasing in-plane anisotropy ( IPA ) of yield strength from 4.4% to 2.5%. The T6 sheet intermediately annealed at 550 °C exhibits high yield strength (326 MPa), which is ascribed to the synergistic effects of precipitation strengthening, texture strengthening and grain refinement. Meanwhile, it presents high volume fractions of Cube ND and random textures. This causes that r ̅ value increases by 9.2% and ∆ r value decreases by 80%.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (48)
Show source-provided references
1. Effect of Ag addition on the precipitation evolution and interfacial segregation for Al–Mg–Si alloy10.1016/j.actamat.2019.09.015 ↗
2. Corrosion behaviour of AA6082 Al–Mg–Si alloy extrusion: the influence of quench cooling rate10.1016/j.corsci.2019.01.030 ↗
3. Influence of quenching temperature on peak aging time and hardness of Al–Mg–Si–Cu alloys strengthened by nano-sized precipitates10.1016/j.msea.2018.11.149 ↗
4. Enhanced aging precipitation behavior and mechanical properties of 6022 Al–Mg–Si alloy with Zr addition10.1016/j.msea.2022.142957 ↗
5. Study on anisotropy of Al–Zn–Mg–Sc–Zr alloy sheet10.1016/j.matchar.2021.110904 ↗
6. Evaluation of mechanical properties and anisotropy of ultra-fine grained 1050 aluminum sheets produced by incremental ECAP10.1016/j.matdes.2017.05.069 ↗
7. The improved mechanical anisotropy of a commercial Al–Cu–Mg–Mn–Si (2017) aluminum alloy by cross rolling10.1002/adem.202100831 ↗
8. The formation of bimodal grain size distribution in Al–Mg–Si–Cu alloy and its effect on the formability10.1016/j.matchar.2017.08.013 ↗
9. Influence of aging treatment on the microstructure, mechanical properties and anisotropy of hot extruded Al-Mg-Si plate10.1016/j.matdes.2019.107999 ↗
10. Deformation, recrystallization and plastic anisotropy of asymmetrically rolled aluminum sheets10.1016/j.msea.2010.09.023 ↗
11. Relationship among grain size, texture and mechanical properties of aluminums with different particle distributions10.1016/j.msea.2019.03.034 ↗
12. Recrystallization texture and r-value of rolled and T4-treated Al–Mg–Si alloy sheets10.4028/www.scientific.net/MSF.495-497.573 ↗
13. Effect of Zn addition on the microstructure, texture evolution and mechanical properties of Al–Mg–Si–Cu alloys10.1016/j.msea.2016.09.084 ↗
14. The dependence of final microstructure, texture evolution and mechanical properties of Al–Mg–Si–Cu alloy sheets on the intermediate annealing10.1016/j.msea.2015.02.029 ↗
15. The effect of Mg and Si content on the microstructure, texture and bendability of Al–Mg–Si alloys10.1016/j.msea.2021.141199 ↗
16. Effect of intermediate annealing time on microstructure, texture and mechanical properties of Al–Mg–Si–Cu alloy10.1016/j.matchar.2018.05.048 ↗
17. Texture evolution and mechanical properties of Al–Mg–Si alloys at different intermediate annealing temperatures10.1007/s12598-019-01315-1 ↗
18. Effect of preform annealing on plastic anisotropy of an age-hardenable Al–Mg–Si alloy10.1016/j.jmatprotec.2017.09.043 ↗
19. Influence of the rolling direction on the microstructure, mechanical, anisotropy and gamma rays shielding properties of an Al–Cu–Li–Mg–X alloy10.1016/j.msea.2018.06.074 ↗
20. Semi-quantitative evaluation of texture components and anisotropy of the yield strength in 2524 T3 alloy sheets10.1016/j.msea.2016.08.013 ↗
21. Investigation of fatigue crack propagation behavior of 5083 aluminum alloy under various stress ratios: Role of grain boundary and Schmid factor10.1016/j.msea.2019.138871 ↗
22. The crystal structure of the β″ phase in Al–Mg–Si alloys10.1016/S1359-6454(97)00493-X ↗
23. Improvement of elevated-temperature strength and recrystallization resistance via Mn-containing dispersoid strengthening in Al–Mg–Si 6082 alloys10.1016/j.jmst.2019.08.027 ↗
24. Coarsening dynamics of self-accommodating coherent patterns10.1016/S1359-6454(01)00335-4 ↗
25. Quantitative predictions of the trans-interface diffusion-controlled theory of particle coarsening10.1016/j.actamat.2010.04.018 ↗
26. Precipitation kinetics in metallic alloys: experiments and modeling10.1016/j.actamat.2021.117338 ↗
27. Nucleation of Al 3 Zr and Al 3 Sc in aluminum alloys: from kinetic Monte Carlo simulations to classical theory10.1103/PhysRevB.69.064109 ↗
28. Experimental and modeling investigations of the non-isothermal and isothermal precipitations in an Al–Cu–Mg–Zr alloy with various pre-precipitation microstructures10.1016/j.matdes.2022.110640 ↗
29. The multi-scale Si-containing phases-assisted improvement in the microstructure and mechanical properties of Al–Mg–xSi–Cu–Zn alloys10.1016/j.msea.2021.142013 ↗
30. Microstructure evolution, texture and laser surface HEACs of Al-Mg-Si alloy for light automobile parts10.1016/j.matchar.2019.110093 ↗
31. Effect of particles on texture banding in an aluminium alloy10.1016/j.scriptamat.2009.09.032 ↗
32. The double-edge effect of second-phase particles on the recrystallization behaviour and associated mechanical properties of metallic materials10.1016/j.pmatsci.2017.10.004 ↗
33. Particle-stimulated nucleation and recrystallization texture initiated by coarsened Al2CuLi phase in Al–Cu–Li alloy10.1016/j.jmrt.2020.12.046 ↗
34. Effect of asymmetric rolling and subsequent ageing on the microstructure, texture and mechanical properties of the Al-Cu-Li alloy10.1016/j.jallcom.2020.155445 ↗
35. Three-dimensional characterization of interaction between β″ precipitate and dislocation in Al–Mg–Si alloy10.1016/j.jallcom.2014.02.059 ↗
36. Quantified contribution of β″ and β′ precipitates to the strengthening of an aged Al–Mg–Si alloy10.1016/j.msea.2019.138776 ↗
37. Coupled precipitation and yield strength modelling for non-isothermal treatments of a 6061 aluminium alloy10.1016/j.actamat.2013.09.041 ↗
38. A model for the yield strength of overaged Al–Zn–Mg–Cu alloys10.1016/S1359-6454(03)00363-X ↗
39. An initial report on achieving high comprehensive performance in an Al–Mg–Si alloy via novel thermomechanical processing10.1016/j.jallcom.2018.06.070 ↗
40. Microhardness measurements and the Hall-Petch relationship in an Al–Mg alloy with submicrometer grain size10.1016/1359-6454(96)00105-X ↗
41. Effect of double-step homogenization treatments on the microstructure and mechanical properties of Al–Cu–Li–Zr alloy10.1016/j.msea.2020.139975 ↗
42. Achieving outstanding combination of strength and ductility of the Al–Mg–Li alloy by cold rolling combined with electropulsing assisted treatment10.1016/j.matdes.2019.108279 ↗
43. Mechanical anisotropy and microstructural changes during cryorolling of Al–Mg–Si alloy10.1016/j.matchar.2015.07.033 ↗
44. Texture control to reduce yield strength anisotropy in the third generation aluminum–copper–lithium alloy: experiments and modeling10.1016/j.msea.2020.140047 ↗
45. Fabrication methods to manufacture isotropic Al-Li alloys and products for space and aerospace applications10.1016/S0921-5093(98)00827-2 ↗
46. Through-thickness heterogeneity and in-plane anisotropy in creep aging of 7050 Al alloy10.1016/j.matdes.2020.109190 ↗
47. Enhanced fracture toughness in an annealed Al–Cu–Mg alloy by increasing Goss/Brass texture ratio10.1016/j.matchar.2016.07.015 ↗
48. Anisotropy in creep-ageing behavior of textured Al–Cu–Mg alloy