journal article·2021-12Open access

Effect of oxidation on spectral and integrated emissivity of Ti-6Al-4V alloy at high temperatures

A. El Bakali, R. Gilblas, T. Pottier, A. Lieurey, Y. Le Maoult

Abstract

Abstract Thermomechanical simulation is challenging for the optimization and virtual monitoring of high temperature shape processes, such as SuperPlastic Forming (SPF) of Titanium alloys alike Ti-6Al-4V (TA6V). Part of this challenge is the accurate and process-representative knowledge of emissivity, which controls radiative heat transfer during the process. In this paper, the characterization of TA6V emissivity, with regards to its oxidation stage, is performed within the [600–1000 °C] thermal range. The main contribution of this work is the use of an in-house characterization bench, enabling the fast radiative heating of samples, and the control of oxide layers thicknesses ranging from 250 nm to 120 µm. An oxidation law is established thanks to post-mortem mass gain and oxide thicknesses measurement, and the various oxide phases are identified. Oxide thicknesses versus heating time were then calculated and implemented in the emissivity analysis. Two patterns are observed for oxide thickness versus temperature: below 900 °C, emissivity values are quasi-continuously increasing with oxide thickness, exhibiting an oxide layer mainly composed by TiO2, above 900 °C, emissivity values are also continuously increasing but with a different trend, due to the formation of alumina, confirmed by X-Ray Diffraction (XRD) measurements. Finally, the dependence of emissivity to temperature and oxide thickness emphasized in this paper constitutes a non-trivial mandatory input to increase the radiative heat transfer simulations codes accuracy.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Calibration and Measurement Techniques · Radiative Heat Transfer Studies · Thermography and Photoacoustic Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (47)

Show source-provided references
1. Yeram · 1970
2. Aerospace Materials and Material Technologies, Volume 1: Aerospace Material Technologies
3. Design and Development Support for Critical Helicopter Applications in Ti-6A1–4V Alloy
4. Micro-scale finishing of the surface and form of a Ti-6Al-4V lightweight rotor obtained by laser powder bed fusion used for air bearing
5. Development of a dovetail fretting fatigue fixture for turbine engine materials10.1016/j.ijfatigue.2008.03.017 ↗
6. A physically based flow rule for the simulation of Ti-6Al-4V forging in the α - β range10.4028/www.scientific.net/MSF.539-543.3661 ↗
7. Relationship Between Diameter of Tensile Specimen and Grain Size for TA6V Castings
8. Analyse et optimisation des procédés de formage de pièces en alliage de Titane
9. Industrial applications of the superplastic forming by using Infra-Red heater10.1016/j.proeng.2017.10.958 ↗
10. Simulation numérique du soudage du TA6V par laser YAG impulsionnel: caractérisation expérimentale et modélisation des aspects thermomécaniques associés à ce procédé
11. A coupled in-situ measurement of temperature and kinematic fields in Ti-6Al-4V serrated chip formation at micro-scale10.1016/j.ijmachtools.2018.03.003 ↗
12. G. Bernhart, J.-P. Arcens, and Y. Le Maoult, Innovative Superplastic Forming Based on In-Situ Infra-Red Sheet Heating, 2013.10.4028/www.scientific.net/MSF.735.415 ↗
13. M.LE Fournier, F. Nazaret, O. Barrau, E. Lebard, and V. Vidal, The use of infra-red heater in superplastic forming: a way of saving costs, in: Proceedings of the 13th World Conference on Titanium, Hoboken, NJ, USA: John Wiley & Sons, Inc., 2016, pp. 1571–1576.10.1002/9781119296126.ch263 ↗
14. Howell · 2010
15. Modest · 2013
16. Behavior of TA6V alloy at high temperature in air plasma conditions: Part 2—thermal diffusivity and emissivity10.1007/s11665-020-04985-6 ↗
17. Interference colors of thin oxide layers on titanium10.1002/col.20403 ↗
18. G. Lütjering and J.C. Williams, Titanium. Berlin, Heidelberg.
19. Alpha-case kinetics and high temperature plasticity of Ti-6Al-4V alloy oxidized in different phase regions10.1016/j.proeng.2017.10.973 ↗
20. Air oxidation behaviour of Ti6Al4V alloy between 650 and 850°10.1016/0010-938X(94)90069-8 ↗
21. Thermal oxidation of Ti6Al4V alloy: Microstructural and electrochemical characterization10.1016/j.matchemphys.2009.09.007 ↗
22. Sefer · 2014
23. E. Dong, W. Yu, Qingwu Cai, L. Cheng, and J. Shi, High-Temperature Oxidation Kinetics and Behavior of Ti-6Al-4V Alloy, Oxid. Met., 88.10.1007/s11085-017-9770-0 ↗
24. Thermophysical properties of solid and liquid Ti-6Al-4V (TA6V) alloy10.1007/PL00021868 ↗
25. Measurement of specific heat capacity and electrical resistivity of industrial alloys using pulse heating techniques10.1023/B:IJOT.0000004101.88449.86 ↗
26. Thermophysical properties of solid phase Ti-6Al-4V alloy over a wide temperature range10.3139/146.110678 ↗
27. Infrared normal spectral emissivity of Ti–6Al–4V alloy in the 500–1150 K temperature range10.1016/j.jallcom.2012.06.117 ↗
28. Study of Ti–6Al–4V alloy spectral emissivity characteristics during thermal oxidation process10.1016/j.ijheatmasstransfer.2016.05.069 ↗
29. Effect of the surface oxidization and nitridation on the normal spectral emissivity of titanium alloys Ti–6Al–4V at 800–1100 K at a wavelength of 1.5 μm10.1016/j.infrared.2016.01.005 ↗
30. A.S. Pagan, B. Massuti-Ballester, G. Herdrich, and A.S. Pagan, Total and Spectral Emissivities of Demising Aerospace Materials Development of the miniaturized Pulsed Plasma Thruster PETRUS View project Characterisation of Demisable Materials View project Total and Spectral Emissivities of Demising Aerospace Materials, 2016.
31. S. Sklarew and A.S. Rabensteine, Emittance Studies of Various High Temperature Materials and Coatings, 1963.
32. H.T. Betz, WADC TR 56–222 (Pt. II), 1957.
33. B. Massuti-Ballester, A.S. Pagan, and G. Herdrich, Determination of total and spectral emissivity of space-relevant materials, in: Proc. 8th Eur. Symp. Aerothermodyn. Sp. Veh., no. 1, 2015.
34. L. Barka, Etude de la survivabilité des débris spatiaux en phase de rentrée atmosphérique (oxydation et émissivité).
35. A fast and versatile method for spectral emissivity measurement at high temperatures10.1063/1.5116425 ↗
36. El Bakali · 2020
37. Survey of emissivity measurement by radiometric methods10.1364/AO.54.000669 ↗
38. A new method of interpolation and smooth curve fitting based on local procedures10.1145/321607.321609 ↗
39. Temperature dependence of the emissivity of platinum in the IR10.1063/1.2966394 ↗
40. Apparatus for measuring the emittance of materials from far infrared to visible wavelengths in extreme conditions of temperature10.1016/j.infrared.2015.01.011 ↗
41. Khanna · 2002
42. Über die Reaktionsgeschwindigkeit bei der Inversion von Rohrzucker durch Säuren
43. High-temperature oxidation of titanium10.1016/0022-5088(67)90017-3 ↗
44. Oxidation of Ti-6Al-4V alloy10.1016/j.jallcom.2008.04.024 ↗
45. Development and characterization of low-emitting ceramics10.1007/s10765-007-0239-2 ↗
46. D. Demange, M. Bejet, and B. Dufour, New Methods for Measuring the Thermal Emissivity of Semi-transparent and Opaque Materials, in: Proceedings of the 2006 International Conference on Quantitative InfraRed Thermography, 2006.10.21611/qirt.2006.087 ↗
47. Texture and porosity effects on the thermal radiative behavior of alumina ceramics10.1007/s10765-008-0510-1 ↗