Preparation of high-tensile-ductility and high-conductivity alumina dispersion-strengthened copper via a cold spray additive manufacturing-friction stir processing composite process
Source abstract
Abstract
The solid-state forming capabilities of cold spray additive manufacturing (CSAM) offer a new method for creating nano-reinforced materials. However, the interface of the deposits often fails to form strong metallurgical bonds, leading to mechanical defects that weaken the material. This study investigates the preparation of highly plastic nano-alumina dispersion-strengthened copper by combining CSAM with friction stir processing (FSP), both solid-state techniques. The results show that FSP treatment fuses the interfaces of the deposited particles, transforming the microstructure from multi-scale, elongated grains to a uniform ultrafine-grained (UFG) structure. The average grain size reduces from 3.1 μm to 0.86 μm, and the proportion of high-angle grain boundaries increases from 42.5 % to 85.2 %. This treatment significantly enhances both mechanical and electrical properties. The ultimate tensile strength increases from 210 MPa to 450 MPa, elongation at break improves from 1 % to 35 %, and electrical conductivity rises from 70 % IACS to 81 % IACS. These findings demonstrate the potential of the combined CSAM-FSP approach for producing high-performance nano-alumina dispersion-strengthened copper with superior mechanical and electrical properties.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (61)
Show source-provided references
1. A review of topology optimization for additive manufacturing: status and challenges10.1016/j.cja.2020.09.020 ↗
2. End to end process evaluation for additively manufactured liquid rocket engine thrust chambers10.1016/j.actaastro.2021.02.034 ↗
3. Machinability of additively manufactured titanium alloys: a comprehensive review10.1016/j.jmapro.2022.01.007 ↗
4. Challenges in additive manufacturing of high-strength aluminium alloys and current developments in hybrid additive manufacturing
5. Additive manufacturing of nickel-based superalloys: a state-of-the-art review on process-structure-defect-property relationship10.1016/j.pmatsci.2023.101108 ↗
6. Additive manufacturing of oxide-dispersion strengthened alloys: materials, synthesis and manufacturing10.1016/j.pmatsci.2022.101049 ↗
7. Selective electron beam melting of oxide dispersion strengthened copper
8. Cold spraying – a materials perspective10.1016/j.actamat.2016.06.034 ↗
9. A novel approach for manufacturing oxide dispersion strengthened (ODS) steel cladding tubes using cold spray technology10.1016/j.net.2019.01.015 ↗
10. Cold Spray metal powder deposition with 9%Cr-steel applied for the HCPB First Wall fabrication: proof of concept and options for ODS steel processing
11. A practical method to improve mechanical and electrical properties of ADS copper prepared by cold spray additive manufacturing through powder pretreatment10.1016/j.jallcom.2023.171319 ↗
12. Tailoring cold spray additive manufacturing of steel 316 L for static and cyclic load-bearing applications10.1016/j.matdes.2021.109575 ↗
13. Effect of hot isostatic pressing (HIP) on microstructure and mechanical properties of Ti6Al4V alloy fabricated by cold spray additive manufacturing
14. Influence of hot isostatic pressing on the properties of 316L stainless steel, Al-Mg-Sc-Zr alloy, titanium and Ti6Al4V cold spray deposits10.1016/j.surfcoat.2020.126736 ↗
15. In-situ Sip/A380 alloy nano/micro composite formation through cold spray additive manufacturing and subsequent hot rolling treatment: microstructure and mechanical properties10.1016/j.jallcom.2018.11.399 ↗
16. Unraveling the effects of hot rolling on microstructure and mechanical properties of cold sprayed Mg/Al clad plates
17. Comparative study on the annealing of cold-sprayed boron nitride nanosheet/copper coating using spark plasma sintering and atmosphere furnace10.1016/j.surfcoat.2022.129041 ↗
18. Influence of surface temperature in the laser assisted cold spray deposition of sequential oxide dispersion strengthened layers: microstructure and hardness10.1016/j.msea.2021.141027 ↗
19. Friction stir processing: a novel technique for fabrication of surface composite10.1016/S0921-5093(02)00199-5 ↗
20. Friction stir processing technology: a review10.1007/s11661-007-9459-0 ↗
21. Friction stir welding and processing10.1016/j.mser.2005.07.001 ↗
22. The study of material flow behaviour in dissimilar material FSW of AA6061 and Cu-B370 alloys plates10.1016/j.jmapro.2018.05.035 ↗
23. Achieving large-area bulk ultrafine Grained Cu via submerged multiple-pass friction stir processing10.1016/j.jmst.2013.09.021 ↗
24. Enhanced combination of mechanical properties and electrical conductivity of a hard state Cu-Cr-Zr alloy via one-step friction stir processing
25. On the role of processing parameters in producing Cu/SiC metal matrix composites via friction stir processing: investigating microstructure, microhardness, wear and tensile behavior10.1016/j.matchar.2010.11.005 ↗
26. Characterization of oxide dispersion strengthened copper based materials developed by friction stir processing10.1016/j.matdes.2014.04.012 ↗
27. Microstructural, mechanical and tribological behavior of aluminum nitride reinforced copper surface composites fabricated through friction stir processing route10.1016/j.msea.2017.02.010 ↗
28. Microstructural evolution and mechanical properties enhancement of a cold-sprayed CuZn alloy coating with friction stir processing10.1016/j.matchar.2017.01.027 ↗
29. A comparative study on the employment of heat treatment, electric pulse processing and friction stir processing to enhance mechanical properties of cold-spray-additive-manufactured copper10.1016/j.surfcoat.2021.126887 ↗
30. Adiabatic shear instability is not necessary for adhesion in cold spray10.1016/j.actamat.2018.07.065 ↗
31. Role of stacking fault energy (SFE) on the high strain rate deformation of cold sprayed Cu and Cu–Al alloy coatings10.1016/j.msea.2021.141242 ↗
32. Mechanical property improvement induced by nanoscaled deformation twins in cold-sprayed Cu coatings10.1016/j.msea.2018.04.113 ↗
33. Dynamical dislocation emission processes from twin boundaries
34. Revealing the maximum strength in nanotwinned copper
35. Dislocation nucleation governed softening and maximum strength in nano-twinned metals10.1038/nature08929 ↗
36. Microstructure and properties of Cu-0.4 wt% Al2O3 composites fabricated by hot extrusion and cold drawing10.1007/s11665-021-06247-5 ↗
37. Friction extrusion of ODS copper rod made from powder10.1016/j.jmapro.2022.10.003 ↗
38. Dynamic strain ageing in fine grained Cu-1 wt%Al2O3 composite processed by two step ball milling and spark plasma sintering10.1016/j.jallcom.2015.09.250 ↗
39. Investigation on microstructure and properties of Cu–Al2O3 composites fabricated by a novel in-situ reactive synthesis10.1016/j.matdes.2015.12.018 ↗
40. Comparison of the properties of cold-sprayed Cu-0.5Cr-0.05Zr alloys after various heat treatments versus forged and vacuum plasma-sprayed alloys10.1007/s11666-013-0028-3 ↗
41. Pure copper components fabricated by cold spray (CS) and selective laser melting (SLM) technology10.1016/j.surfcoat.2020.125936 ↗
42. Effect of vacuum heat treatment on tensile strength and fracture performance of cold-sprayed Cu-4Cr-2Nb coatings10.1016/j.apsusc.2011.01.076 ↗
43. Mechanical properties of cold-sprayed and thermally sprayed copper coatings10.1016/j.surfcoat.2005.10.007 ↗
44. Hoganas A.B., 2018. Sweden. Copper Alloy System with Unrivalled Performance 〈https//www.hoganas.com/en/powder-technologies/glipcop〉 (2018), Accessed 17th Apr 2018.
45. A novel approach for strengthening Cu–Y2O3 composites by in situ reaction at liquidus temperature10.1016/j.msea.2013.07.007 ↗
46. LEDS in ultra-high strain-rate deformation10.1002/pssa.2211490118 ↗
47. Microstructure refinement of cold-sprayed copper investigated by electron channeling contrast imaging10.1017/S1431927614001664 ↗
48. Nanotwinning-assisted dynamic recrystallization at high strains and strain rates10.1038/s41563-022-01250-0 ↗
49. Precipitation-induced grain growth simulation of friction-stir-welded AA6082-T610.1007/s11665-017-2639-1 ↗
50. Concurrently achieving strength-ductility combination and robust anti-wear performance in an in-situ high-entropy bulk metallic glass composite10.1016/j.compositesb.2024.111222 ↗
51. Effects of Al/Si on the oxidation behavior of a TiZrV0.5Nb0.5 refractory high entropy alloy at 1000 ℃10.1016/j.corsci.2023.111527 ↗
52. Achieving excellent mechanical and robust lubrication behavior in the CoCrNi medium-entropy alloy via in-situ graphite10.1016/j.carbon.2024.119503 ↗
53. W.F. Smith, Foundations of Materials Science and Engineering, 1993.
54. The deformation and ageing of mild steel: III discussion of results10.1088/0370-1301/64/9/303 ↗
55. The cleavage strength of polycrystals
56. Creep deformation of dispersion-strengthened copper10.1007/BF02649859 ↗
57. Comment on graphs relating some property to stacking fault energy10.1016/0036-9748(81)90017-X ↗
58. Nano-scale precipitates: the key to high strength and high conductivity in Al alloy wire10.1016/j.matdes.2017.06.062 ↗
59. Modeling the electrical resistivity of deformation processed metal–metal composites10.1016/j.actamat.2014.06.013 ↗
60. Ultrafine grained copper alloy sheets having both high strength and high electric conductivity10.1016/j.matlet.2009.05.021 ↗
61. The effects of equal channel angular extrusion on the mechanical and electrical properties of alumina dispersion-strengthened copper alloys10.1016/j.msea.2012.12.007 ↗