Effects of grain size and β fraction on the deformation modes of a Ti-6Al-2Sn-4Zr-2Mo-Si alloy with equiaxed (α + β) microstructures: Slip trace analysis and multiscale simulation of polycrystal plasticity
Source abstract
Abstract
This study investigates the mechanisms behind the great mechanical properties observed at room temperature for a dual-phase Ti-6Al-2Sn-4Zr-2Mo-Si titanium alloy with equiaxed (α + β) microstructures. More precisely, analyzing the material deformation modes and the possible effects of β fraction and grain size was done to better understand such micromechanisms. With this idea in mind, uniaxial tensile deformation tests were performed at room temperature, and the resulting mechanical behaviors were analyzed. It was observed that increasing β fraction would enhance the overall ductility and work hardening while conversely decreasing the material resistance. Additionally, the material strengthening due to grain size effect, quantified by the Hall-Petch parameter, was also found to be dependent on β fraction. Slip trace analysis was conducted to understand the effects of grain size and β fraction on the activation of the basal , prismatic , and pyramidal slip systems and their critical resolved shear stress (CRSS) ratios were established. The qualitative study of CRSS ratios revealed that at smaller grain sizes, the basal slip systems were dominant (e.g. basal/prismatic CRSS ratio of 0.86 for d=2.98 µm) whereas the prismatic slip systems were prevalent and more easily activated for coarser grains (e.g. basal/prismatic CRSS ratio of 1.19 for d=4.21 µm). Such CRSS ratios were then used to identify the material parameters of a self-consistent multiscale model employed to reproduce the tensile behaviors. For a more quantitative analysis, the CRSS values were evaluated and correlated to grain sizes with Hall-Petch relations. Clear correlations regarding grain size and β fraction were found for the CRSS of prismatic and pyramidal systems. However, special attention was given to the ambiguous results regarding basal slip systems because of the potential manifestation of the compatibility stresses and grain boundary sliding mechanisms due to the higher density of grain boundaries at small grain sizes.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Microstructure and mechanical properties · Magnesium Alloys: Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (54)
Show source-provided references
1. Microstructure and Mechanical Properties of Titanium Alloys
2. Structure and Properties of Titanium and Titanium Alloys
3. Excellent balance of ultimate tensile strength and ductility in a Ti-6Al-2Sn-4Zr-2Mo-Si alloy having duplex α+α’ microstructure: effect of microstructural factors from experimental study and machine learning10.2320/matertrans.MT-MLA2022009 ↗
4. Deformation behavior and microstructure evolution of titanium alloys with lamellar microstructure in hot working process: a review10.1016/j.jmst.2019.07.052 ↗
5. Effect of heat treatment on the microstructure and mechanical properties of high-strength Ti-6Al-4V–5Fe alloy10.2320/matertrans.M2018267 ↗
6. Extension of the Hall-Petch relation to two-ductile-phase alloys10.1080/01418619308207175 ↗
7. S. Graff, Micromechanical Modeling of the Deformation of HCP Metals, Thesis dissertation, Technische Universität Berlin, 2008.
8. Modeling Ti-6Al-4V using crystal plasticity, calibrated with multi-scale experiments, to understand the effect of the orientation and morphology of the α and β phases on time dependent cyclic loading10.1016/j.jmps.2020.104192 ↗
9. An extension of the self-consistent scheme to plastically-flowing polycrystals10.1016/0022-5096(78)90003-0 ↗
10. Crystal plasticity modeling of beta phase deformation in Ti-6Al-4V10.1088/1361-651X/aa841c ↗
11. A study of active deformation systems in titanium alloys: dependence on alloy composition and correlation with deformation texture10.1016/S0921-5093(02)00421-5 ↗
12. A multi-scale characterization of deformation twins in Ti6Al4V sheet material deformed by simple shear10.1016/j.msea.2010.03.039 ↗
13. Activated slip systems in bimodal Ti-6Al-4V plastically deformed at low and moderately high temperatures10.1016/j.msea.2020.140211 ↗
14. Role of grain size and crystallographic texture on tensile behavior induced by sliding mechanism in Ti-6Al-4V alloy10.1016/j.msea.2019.138835 ↗
15. Anisotropy in the plastic flow properties of single-crystal α titanium determined from micro-cantilever beams10.1016/j.actamat.2009.07.064 ↗
16. Crystal plasticity modeling of slip activity in Ti-6Al-4V under high cycle fatigue loading10.1016/j.ijplas.2008.08.004 ↗
17. Deformation behavior of HCP Ti-Al alloy single crystals10.1007/s11661-002-0153-y ↗
18. Mechanical behavior and texture prediction of Ti-6Al-4V based on elastic viscoplastic self-consistent modelling10.1088/1757-899X/82/1/012027 ↗
19. A three-dimensional crystal plasticity model for duplex Ti-6Al-4V10.1016/j.ijplas.2006.11.006 ↗
20. On the strength of dislocation interactions and their effect on latent hardening in pure Magnesium10.1016/j.ijplas.2014.06.010 ↗
21. Pencil glide formulation for polycrystal modelling10.1016/0956-716X(95)00051-V ↗
22. Modeling of large plastic deformation behavior and anisotropy evolution in cold rolled bcc steels using the viscoplastic Φ-model-based grain-interaction10.1016/j.msea.2011.03.110 ↗
23. Efficient simulation of single and poly-crystal plasticity based on the pencil glide mechanism10.5802/crmeca.44 ↗
24. Methodology for estimating the critical resolved shear stress ratios of α-phase Ti using EBSD-based trace analysis10.1016/j.actamat.2013.08.042 ↗
25. Research progress on slip behavior of α-Ti under quasi-static loading: a review10.3390/met12101571 ↗
26. Texture analysis with MTEX – free and open source software toolbox10.4028/www.scientific.net/SSP.160.63 ↗
27. Single crystal modeling for structural calculations: Part 1 – Model presentation10.1115/1.2903374 ↗
28. Background on Modeling
29. Crystalline Viscoplasticity Applied to Single Crystals
30. Strain-path dependent hardening models with rigorously identical predictions under monotonic loading10.1016/j.mechrescom.2020.103615 ↗
31. Plastic deformation and fracture behaviour of Ti-6Al-4V alloy loaded with high strain rate under various temperatures10.1016/S0921-5093(97)00471-1 ↗
32. Chin. J. Aeronaut. · 2016 · 29 · 54210.1016/j.cja.2015.08.004 ↗
33. Crystal plasticity based FE model for understanding microstructural effects on creep and dwell fatigue in Ti-624210.1115/1.2204942 ↗
34. Fretting modelling with a crystal plasticity model of Ti6Al4V10.1016/j.commatsci.2006.01.015 ↗
35. Deformation and creep modeling in polycrystalline Ti-6Al alloys10.1016/S1359-6454(03)00289-1 ↗
36. Impact of texture on mechanical properties in an advanced titanium alloy10.1016/S0921-5093(00)02034-7 ↗
37. On the optimization of temperature and cooling rate to maximize strength and ductility of near α titanium alloy IMI 83410.1016/j.msea.2021.142052 ↗
38. β-transformed domains enhanced tensile properties and the related deformation behavior of a near alpha titanium alloy
39. Achieving high tensile strength-ductility synergy of a fully-lamellar structured near alpha titanium alloy at extra-low temperatures10.1016/j.jallcom.2022.166363 ↗
40. Yielding nature and Hall-Petch relationships in Ti-6Al-4V alloy with fully equiaxed and bimodal microstructures10.1016/j.scriptamat.2019.07.015 ↗
41. The plastic deformation of polycrystalline aggregates10.1080/14786436208201857 ↗
42. Petch relation and grain boundary sources
43. The deformation of plastically non-homogeneous materials10.1080/14786437008238426 ↗
44. On the physical meaning of the Hall-Petch constant
45. Hall-Petch relation in two-phase TiAl alloys10.1016/S0921-5093(96)10446-9 ↗
46. Two-dimensional sections of the yield locus of a Ti-6%Al-4%V alloy with a strong transverse-type crystallographic α-texture10.1016/0921-5093(95)09780-5 ↗
47. The effect of crystal orientation and boundary misorientation on tensile boundary cavitation during hot tension deformation of Ti-6Al-4V
48. Stress-state dependence of slip in titanium-6Al-4V and other H.C.P. metals10.1016/0001-6160(81)90049-3 ↗
49. The deformation of α phase titanium
50. Mechanical properties of age-hardened titanium-aluminum alloys10.1016/0001-6160(70)90043-X ↗
51. Phenomenological and microstructural analysis of room temperature creep in titanium alloys10.1016/S1359-6454(99)00426-7 ↗
52. Slip-stimulated grain boundary sliding in Ti-6Al-4V at room temperature10.1016/j.mtla.2018.100189 ↗
53. The activity of non-basal slip systems and dynamic recovery at room temperature in fine-grained AZ31B magnesium alloys10.1016/S1359-6454(03)00005-3 ↗
54. Polycrystalline strengthening10.1016/0001-6160(75)90150-9 ↗