Effect of nano-Al2O3 addition on microstructure and mechanical properties of Ti2AlNb-based composites prepared by powder metallurgy
Source abstract
Abstract
To meet the commercial application, the mechanical properties of Ti 2 AlNb-based alloys must be improved. However, the strengthening mechanism of the Ti 2AlNb-based composites with Al 2O 3 particles needs further to investigate. Nano-Al 2O 3/Ti‐22Al‐25Nb composites are prepared by mechanical alloying (MA), high-energy ball milling (HEBM), and hot pressing (HP). The purpose of this study is to identify the effect of Al 2O 3 content on the microstructure and mechanical properties of the composites. The results show that the grain size decreases, and phase transformation occurs with an increase in the Al 2O 3 content. With the increase of Al 2O 3 content from 2 wt.% to 6 wt.%, the microstructure of Ti 2 AlNb-based composites transformed from the ultrafine acicular O phase to the uniform equiaxed O phase. The hardness and ultimate compressive strength of the Ti 2AlNb-based composites first increase and then decrease. The hardness of the composite is up to 8.6 GPa when the Al 2O 3 content is 6 wt.%, almost twice that of Ti‐22Al‐25Nb alloy. The hardening effect is the result of a higher volume fraction of the O phase and grain refinement with addition of Al 2O 3 particles. The optimal combination of hardness, ultimate compressive strength, and strain-to-failure of the composite with 2 wt.% Al 2O 3 is 5.9 GPa, 2190 MPa, and 8.1%, respectively. The strengthening mechanisms of Al 2O 3 phase dispersion and ultrafine acicular O phase precipitation are proposed and confirmed. This research offers a new idea for the wider application of Ti 2AlNb-based composites.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Intermetallics and Advanced Alloy Properties · MXene and MAX Phase Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (53)
Show source-provided references
1. A new ordered orthorhombic phase in a Ti3Al-Nb alloy10.1016/0001-6160(88)90141-1 ↗
2. Microstructural investigations for laser welded joints of Ti-22Al-25Nb alloy sheets upon large deformation at elevated temperature10.1016/j.matdes.2015.11.007 ↗
3. Microstructure and mechanical properties of Ti2AlNb-based alloys synthesized by spark plasma sintering from pre-alloyed and ball-milled powder10.1002/adem.201700659 ↗
4. Tribological properties of Ti2AlNb matrix composites containing few-layer graphene fabricated by spark plasma sintering10.3390/met10070924 ↗
5. Reaction mechanism in high Nb containing TiAl alloy by elemental powder metallurgy10.1016/S1003-6326(06)60339-7 ↗
6. Influence of mechanical alloying on the microstructure and mechanical properties of powder metallurgy Ti2AlNb-based alloy10.1016/j.powtec.2017.03.034 ↗
7. Microstructure and mechanical properties of Ti-22Al-25Nb alloy fabricated by vacuum hot pressing sintering10.1016/j.msea.2014.08.018 ↗
8. Microstructure and high temperature tensile properties of Ti22Al25Nb alloy prepared by reactive sintering with element powders10.1016/j.msea.2014.04.086 ↗
9. Microstructure and mechanical properties of Ti-22Al-25Nb alloy fabricated by elemental powder metallurgy10.1016/j.msea.2015.12.037 ↗
10. Microstructure and mechanical properties of a Ti-22Al-25Nb alloy fabricated from elemental powders by mechanical alloying and spark plasma sintering10.1016/j.jallcom.2017.01.354 ↗
11. Dual structure O+B2 for enhancement of hardness in furnace-cooled Ti2AlNb-based alloys by powder metallurgy10.1016/j.apt.2017.04.009 ↗
12. Fabrication of a high strength and ductility Ti-22Al-25Nb alloy from high energy ball-milled powder by spark plasma sintering10.1016/j.jallcom.2018.01.279 ↗
13. Effect of ball-milling time on mechanical and magnetic properties of carbon nanotube reinforced FeCo alloy composites10.1016/j.matdes.2017.02.091 ↗
14. Effect of milling conditions on structural evolution and phase stability of [Ti(H2)+Al+Nb] powder mixtures10.1016/j.msea.2007.03.105 ↗
15. Effect of hydrogen on the formation of the structure and phase composition in the Ti2AlNb-based alloy10.1134/S0031918X10020067 ↗
16. Grain refining of Er added to Ti–22Al–25Nb alloy and morphology of erbium precipitates10.1007/s12598-013-0006-4 ↗
17. Formation of diverse B2+O structure and hardness of Mo-modified Ti-22Al-25Nb alloys upon cooling10.1016/j.vacuum.2019.04.034 ↗
18. Hot deformation behavior and microstructural evolution of Ti-22Al-25Nb-1.0B alloy prepared by elemental powder metallurgy10.1016/j.jallcom.2016.10.228 ↗
19. Effect of W addition on phase transformation and microstructure of powder metallurgic Ti-22Al-25Nb alloys during quenching and furnace cooling10.1016/j.cja.2018.08.009 ↗
20. Effect of volume fraction of reinforcement on microstructure and mechanical properties of in situ (Ti, Nb)B/Ti(2)AlNb composites with tailored three-dimensional network architecture10.3390/ma15249070 ↗
21. Evaluation of an SCS-6/Ti-22Al-23Nb "Orthorhombic" composite10.1557/PROC-273-43 ↗
22. Room-temperature tensile and high-cycle-fatigue strength of fine TiB particulate-reinforced Ti-22Al-27Nb composites10.1007/s11661-004-0244-z ↗
23. Precipitation of carbides and dissolution of Widmanstätten structure for enhanced hardness in Ti2AlNb-based alloys10.1007/s11665-019-03965-9 ↗
24. In situ synthesized Ti2AlNb-based composites produced by selective laser melting by addition of SiC-whiskers10.1016/j.matlet.2021.129956 ↗
25. High-temperature anti-wear behavior of alumina-reinforced Ti–Zr–Mo alloy composites10.1016/j.wear.2014.08.003 ↗
26. Al2O3/Mo composite and its tribological behavior against AISI201 stainless steel at elevated temperatures10.1016/j.ijrmhm.2013.12.014 ↗
27. Effect of Al2O3 particles on mechanical properties of directionally solidified intermetallic Ti–46Al–2W–0.5Si alloy10.1016/S0921-5093(03)00445-3 ↗
28. Microstructure and mechanical properties of Al2O3/NiAl in situ composites by hot-press-aided reaction synthesis10.4028/www.scientific.net/AMR.581-582.548 ↗
29. Microstructure and mechanical properties of Ti3(Al,Ga)C2/Al2O3 composites prepared by in situ reactive hot pressing10.1007/s40145-020-0428-z ↗
30. Microstructure and mechanical properties of carbon nanotubes reinforced titanium matrix composites fabricated via spark plasma sintering10.1016/j.msea.2017.02.019 ↗
31. Microstructure and mechanical properties of 7075 Al alloy based composites with Al2O3 nanoparticles10.1080/13640461.2017.1316954 ↗
32. Mechanical alloying and milling10.1016/S0079-6425(99)00010-9 ↗
33. Waseda · 2011
34. Thermodynamics and kinetics of amorphisation during mechanical alloying10.4028/www.scientific.net/MSF.88-90.43 ↗
35. Precipitation behavior of Widmanstätten O phase associated with interface in aged Ti2AlNb-based alloys10.1016/j.matchar.2018.09.009 ↗
36. Effect of orthorhombic case on the creep rupture of Ti-22Al-25Nb (at%) orthorhombic alloy10.1016/j.msea.2017.05.003 ↗
37. Titanium/nanodiamond nanocomposites: effect of nanodiamond on microstructure and mechanical properties of titanium10.1016/j.matdes.2017.06.015 ↗
38. Synthesis, microstructure and mechanical properties of (Ti,Mo)Al/Al2O3 in situ composites by reactive hot pressing10.1557/jmr.2017.60 ↗
39. Microstructure evolution, electrochemical properties and in-vitro properties of Ti-Nb-Zr based biocomposite by hydroxyapatite bioceramic10.1016/j.jallcom.2018.06.132 ↗
40. Microstructures and tensile properties of Ti2AlNb and Mo-modified Ti2AlNb alloys fabricated by hot isostatic pressing10.1016/j.msea.2020.139043 ↗
41. Investigation of the phase transformations in Ti-22Al-25Nb alloy10.1016/j.matchar.2016.02.011 ↗
42. Investigation on the microstructure, room and high temperature mechanical behaviors and strengthening mechanisms of the (TiB+TiC)/TC4 composites10.1016/j.jallcom.2017.08.017 ↗
43. Effect of phase transition caused by different treatment process on mechanical properties of powder metallurgy Ti-22Al-24Nb-0.5Mo (at%) alloys10.1016/j.matchar.2019.110022 ↗
44. Effects of direct rolling deformation on the microstructure and tensile properties of the 2.5 vol% (TiBw+TiCp)/Ti composites10.1016/j.msea.2016.12.113 ↗
45. B2 grain growth and particle pinning effect of Ti-22Al-25Nb orthorhombic intermetallic alloy during heating process10.1016/j.intermet.2012.04.021 ↗
46. Examination of the Zener relationship between grain size and particle dispersion10.2320/matertrans1989.38.950 ↗
47. B2 grain size refinement and its effect on room temperature tensile properties of a Ti–22Al–27Nb orthorhombic intermetallic alloy10.1016/S1359-6462(02)00462-1 ↗
48. Solution treatment for enhanced hardness in Mo-modified Ti2AlNb-based alloys10.1016/j.jallcom.2019.07.149 ↗
49. Anti-correlation between solution strengthening and precipitation strengthening in lamellar O microstructures of a Ti2AlNb based alloy10.1016/j.jallcom.2020.156470 ↗
50. Formation mechanism of an α2 phase-rich layer on the surface of Ti-22Al-25Nb alloy10.1016/j.matchar.2018.08.030 ↗
51. Microstructure and mechanical properties of Al2O3 ceramic and Ti2AlNb alloy joints brazed with Al2O3 particles reinforced Ag–Cu filler metal10.1016/j.vacuum.2021.110430 ↗
52. Microstructure control and mechanical properties from isothermal forging and heat treatment of Ti–22Al–25Nb (at%) orthorhombic alloy10.1016/j.intermet.2014.07.011 ↗
53. Influence of heat treatment on the microstructure evolution and mechanical properties of graphene/Ti2AlNb composites synthesized via spark plasma sintering10.1007/s11665-020-05185-y ↗