Mechanical behavior of bilayer Ti6Al4V composite under quasi-static and dynamic compression
Source abstract
Abstract
Bilayer structure and homogeneous structure of Ti6Al4V (TC4) alloy were fabricated by High energy ball milling (HEBM) and Fast Hot-Press Sintering (FHPS). The flake TC4 (F-TC4) powders were obtained from spherical TC4 (S-TC4) powders by HEBM, and the bilayer F/S-TC4 composite was prepared from F-TC4 and S-TC4 powders. The microstructure and micro-hardness evolution along the interface of the bilayer composite were investigated. It was found that the hardness decreased gradually from the F-TC4 side to the S-TC4 side. Moreover, an obvious morphology difference in the interface was observed, typical Widmanstatten structure on the S-TC4 side while an equiaxed structure on the F-TC4 side. In addition, the mechanical properties of the alloy and composite with different structures were studied under quasi-static and dynamic compression. The results revealed that the bilayer F/S-TC4 composite showed great strength improvement with little plasticity sacrifice as compared to traditional S-TC4 alloy.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Aluminum Alloys Composites Properties · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. Softening and compressive twinning in nanosecond ultraviolet pulsed laser-treated Ti6Al4V10.1016/j.scriptamat.2015.10.027 ↗
2. Titanium metal matrix composites: an overview10.1016/j.compositesa.2019.04.005 ↗
3. Microstructure and mechanical properties of GNPs and in-situ TiB hybrid reinforced Ti–6Al–4V matrix composites with 3D network architecture10.1016/j.msea.2022.143536 ↗
4. Enhanced strain-hardening capability in graphene nanoplatelets reinforced Ti composites through tailoring a novel three-dimensional interface structure10.1016/j.compositesa.2022.106892 ↗
5. High temperature mechanical properties of as-extruded TiBw/Ti60 composites with ellipsoid network architecture10.1016/j.jallcom.2016.07.118 ↗
6. The superior mechanical and physical properties of nanocarbon reinforced bulk composites achieved by architecture design – a review10.1016/j.pmatsci.2020.100672 ↗
7. Mechanical properties and strengthening mechanisms of titanium matrix nanocomposites reinforced with onion-like carbons10.1016/j.compositesa.2020.105834 ↗
8. Beyond seashells: bioinspired 2D photonic and photoelectronic devices10.1002/adfm.201901460 ↗
9. Enhanced mechanical properties of graphene (reduced graphene oxide)/aluminum composites with a bioinspired nanolaminated structure10.1021/acs.nanolett.5b03492 ↗
10. High-temperature damage-tolerance of a hot-rolled brick-and-mortar Ti2Ni/TiNi composite10.1016/j.matlet.2022.132555 ↗
11. Influential mechanisms on interface bonding of hot-rolled TB9/TC4 laminated composites10.1016/j.msea.2022.143749 ↗
12. High strain rate deformation of explosion-welded Ti6Al4V/pure titanium10.1016/j.dt.2019.10.002 ↗
13. Mechanical behavior of bilayer structures of Ti64 alloy and its composites with TiC or TiB under quasi-static and dynamic compression10.1016/j.matdes.2022.111205 ↗
14. A study of precipitation strengthening and recrystallization behavior in dilute Al–Er–Hf–Zr alloys10.1016/j.msea.2015.05.027 ↗
15. Graphene nanoplatelets induced laminated heterogeneous structural titanium matrix composites with superior mechanical properties10.1016/j.ceramint.2022.08.335 ↗
16. Towards high performance GNFs/Ti composite through simultaneously manipulating laminated microstructure and interface reaction10.1016/j.msea.2021.141230 ↗
17. Dynamic shear deformation and failure of Ti-5Al-5Mo-5V–1Cr-1Fe titanium alloy10.1016/j.msea.2017.03.114 ↗
18. Compressive properties and micro-structural characteristics of Ti–6Al–4V fabricated by electron beam melting and selective laser melting10.1016/j.msea.2019.138204 ↗
19. Dynamic mechanical properties and failure characteristics of electron beam melted Ti-6Al-4V under high strain rate impact loadings10.1016/j.msea.2020.139794 ↗
20. Investigation on the microstructure, room and high temperature mechanical behaviors and strengthening mechanisms of the (TiB+TiC)/TC4 composites10.1016/j.jallcom.2017.08.017 ↗
21. Effect of ball-milling time on mechanical and magnetic properties of carbon nanotube reinforced FeCo alloy composites10.1016/j.matdes.2017.02.091 ↗
22. Effect of ball milling time on graphene nanosheets reinforced Al6063 composite fabricated by pressure infiltration method10.1016/j.carbon.2018.09.041 ↗
23. Effect of different milling media for surface coating on the copper powder using two kinds of ball mills with discrete element method simulation10.3390/coatings10090898 ↗
24. The influence of defect structures on the mechanical properties of Ti-6Al-4V alloys deformed by high-pressure torsion at ambient temperature10.1016/j.msea.2016.12.033 ↗
25. Breaking through the dynamic strength-ductility trade-off in TiB reinforced Ti composites by incorporation of graphene nanoplatelets10.1016/j.compositesb.2021.109499 ↗
26. Significance of grain boundaries and stacking faults on hydrogen storage properties of Mg2Ni intermetallics processed by high-pressure torsion10.1016/j.actamat.2015.03.036 ↗
27. Size effect of flake Ti powders on the mechanical properties in graphene nanoflakes/Ti fabricated by flake powder metallurgy10.1016/j.compositesa.2019.04.027 ↗
28. Interface microstructure and strengthening mechanisms of multilayer graphene reinforced titanium alloy matrix nanocomposites with network architectures10.1016/j.matdes.2020.109119 ↗
29. Tensile and bending behaviors and characteristics of laminated Ti-(TiBw/Ti) composites with different interface status10.1016/j.compositesb.2016.10.001 ↗
30. Gradient grain distribution and enhanced properties of novel laminated Ti–TiBw/Ti composites by reaction hot-pressing10.1016/j.msea.2013.12.013 ↗
31. Experimental determination of linear and nonlinear mechanical properties of laminated soft composite material system10.1016/j.compositesb.2013.09.043 ↗
32. Effects of bondline thickness on Mode-I nonlinear interfacial fracture of laminated composites: an experimental study10.1016/j.compositesb.2012.10.048 ↗
33. Toughening of laminated ZrB2–SiC ceramics with residual surface compression10.1016/j.jeurceramsoc.2011.05.024 ↗
34. Effect of build orientation on dynamic compressive behaviour of Ti-6Al-4V alloy fabricated by selective laser melting10.1016/j.msea.2022.144440 ↗
35. High-strain-rate plastic deformation and fracture behaviour of Ti-5Al-5Mo-5V–1Cr-1Fe titanium alloy at room temperature10.1016/j.mechmat.2017.08.007 ↗
36. Dynamic compressive response of electron beam melted Ti–6Al–4V under elevated strain rates: microstructure and constitutive models
37. Stress wave propagation effects in two-and three-layered composite materials10.1177/0021998304040564 ↗
38. Influence of deformation conditions on the inhomogeneity of plastic flow of structurally graded bimetal systems10.1016/j.promfg.2018.07.272 ↗