Effect of milling time on microstructural and mechanical properties of nano-Al2O3P/6061Al composites prepared by transient liquid-phase sintering
Source abstract
Abstract
In this study, 5 vol% Al 2O 3 nanoparticles reinforced 6061 Al matrix nanocomposite was prepared by mechanical alloying the corresponding powders followed by hot-pressing. The effect of the milling time on the morphology of powder as well as the microstructure and mechanical properties of resulting nanocomposites was studied. The result shows that the effect of the milling time on the mechanical properties of nanocomposites comes from its effect on the distribution of Al 2O 3 nanoparticles in Al matrix. The long milling time is required to uniformly disperse Al 2O 3 nanoparticles within Al grains, in order to obtain good mechanical properties. The nanocomposite made from the powder milled for 50 h exhibits a tensile strength of 602 MPa and an elongation to failure of 8.8%, which are higher than those ever reported for the similar materials. The higher mechanical properties are mainly attributed to Orowan strengthening, grain boundary strengthening, and high dislocation density.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. Fabrication of nano-sized Al2O3 reinforced casting aluminum composite focusing on preparation process of reinforcement powders and evaluation of its properties10.1016/j.compositesb.2013.07.008 ↗
2. Effects of nano-SiCp content on microstructure and mechanical properties of SiCp/A356 composites assisted with ultrasonic treatment10.1016/S1003-6326(18)64862-9 ↗
3. Preparation of super-high strength nanostructured B4C reinforced Al-2Cu aluminum alloy matrix composites by mechanical milling and hot press method: microstructural, mechanical and tribological10.1016/j.apt.2017.10.007 ↗
4. Enhancement of strength and ductility by interfacial nano-decoration in carbon nanotube/aluminum matrix composites10.1016/j.carbon.2019.12.038 ↗
5. Development of high strength and toughness nano-SiCp/A356 composites with ultrasonic vibration and squeeze casting10.1016/j.jmatprotec.2019.01.021 ↗
6. Enhancing strength and ductility synergy through heterogeneous structure design in nanoscale Al2O3 particulate reinforced Al composites10.1016/j.matdes.2019.107629 ↗
7. Effects of SiC nanoparticle content on the microstructure and tensile mechanical properties of ultrafine grained AA6063-SiCnp nanocomposites fabricated by powder metallurgy10.1016/j.jmst.2016.09.022 ↗
8. Effect of reinforcement particle size on quasistatic and dynamic mechanical properties of Al-Al2O3 composites10.1016/j.jallcom.2019.05.080 ↗
9. Improved mechanical properties of AlSi7Mg/nano-SiCp composites fabricated by selective laser melting10.1016/j.jallcom.2019.151926 ↗
10. Structural evolution during mechanical milling of nanometric and micrometric Al2O3 reinforced Al matrix composites10.1016/j.msea.2006.04.116 ↗
11. Microstructural evolution and its effects on mechanical properties of spray deposited SiCp/8009Al composites during secondary processing10.1016/S1003-6326(08)60416-1 ↗
12. Microstructure and mechanical properties of graphene nanoplates reinforced pure Al matrix composites prepared by pressure infiltration method10.1016/j.jallcom.2017.10.283 ↗
13. Effects of ZrO2 nanoparticle content on microstructure and wear behavior of titanium matrix composite10.1016/j.jmrt.2020.05.021 ↗
14. Mechanically alloyed AlN particle-reinforced Al-6061 matrix composites: powder processing, consolidation and mechanical strength and hardness of the as-extruded materials10.1016/j.msea.2006.03.074 ↗
15. Modelling of carbon nanotube dispersion and strengthening mechanisms in Al matrix composites prepared by high energy ball milling-powder metallurgy method10.1016/j.compositesa.2016.11.029 ↗
16. Improving the mechanical properties of B4C/Al composites by solid-state interfacial reaction10.1016/j.jallcom.2020.154521 ↗
17. Effect of mechanical milling on the morphology and structural evaluation of Al-Al2O3 nanocomposite powders
18. Enhanced combination of strength and ductility in ultrafine-grained aluminum composites reinforced with high content intragranular nanoparticles10.1016/j.msea.2018.12.090 ↗
19. Correlation between grain boundary evolution and mechanical properties of ultrafine-grained metals10.1016/j.mechmat.2020.103321 ↗
20. Reliability and interpretation of the microstructural parameters determined by X-ray line profile analysis for nanostructured materials
21. Effect of Al2O3 particles on mechanical and tribological properties of Al–Mg dual-matrix nanocomposites10.1016/j.ceramint.2019.11.028 ↗
22. Mechanical properties and microstructures of Al-10Mg-4.5Si matrix composites reinforced by carbon nanotubes10.1016/j.jallcom.2019.04.101 ↗
23. Effect of nano Al2O3 coated Ag reinforced Cu matrix nanocomposites on mechanical and tribological behavior synthesis by P/M technique10.1177/0021998320934860 ↗
24. Utilization of improved machine learning method based on artificial hummingbird algorithm to predict the tribological behavior of Cu-Al2O3 nanocomposites synthesized by in situ method10.3390/math10081266 ↗
25. Experimental and modeling investigation on SiCp distribution in powder metallurgy processed SiCp/2024 Al composites10.1016/j.msea.2010.05.006 ↗
26. The performance of aluminium-matrix composites with nanometric particulate Si-N-C reinforcement10.1016/S0266-3538(98)00064-5 ↗
27. Effect of ball milling on microstructure and mechanical properties of Mg2B2O5w/6061Al matrix composites10.1016/S1875-5372(16)30126-6 ↗
28. Tensile properties of nanometric Al2O3 particulate-reinforced aluminum matrix composites10.1016/j.matchemphys.2004.02.002 ↗
29. Microstructure and synergistic-strengthening efficiency of CNTs-SiCp dual-nano reinforcements in aluminum matrix composites10.1016/j.compositesa.2017.11.013 ↗
30. Microstructure and mechanical properties of 45 vol% SiCp/7075Al composite10.1016/j.jmst.2015.01.012 ↗
31. The compressive properties of 2024Al matrix composites reinforced with high content SiC particles at various strain rates10.1016/j.msea.2007.12.021 ↗
32. Effect of reinforcement connectivity on the elasto-plastic behavior of aluminum composites containing sub-micron alumina particles10.1016/S1359-6454(03)00431-2 ↗
33. The mechanical response of a 6061-T6 A1/A12O3 metal matrix composite at high rates of deformation10.1016/0956-7151(95)00123-D ↗
34. Microstructure and mechanical properties of SiCnp /Al6082 aluminum matrix composites prepared by squeeze casting combined with stir casting10.1016/j.jmatprotec.2020.116699 ↗
35. Microstructure and yield strength of ultrafine grained aluminum processed by hot isostatic pressing10.1016/j.msea.2006.12.127 ↗
36. Developing a high-strength Al-Mg-Si-Sc-Zr alloy for selective laser melting: crack-inhibiting and multiple strengthening mechanisms10.1016/j.actamat.2020.03.060 ↗
37. Fabrication and investigation on the properties of ilmenite (FeTiO3)-based Al composite by accumulative roll bonding10.1177/0021998319876684 ↗