journal article·2022-09

Formation mechanism of TiB2 nanoparticles and development of TiB2p/6201 nanocomposites as a neoteric conducting material

Kai Zhao, Mengmeng Liu, Huijun Kang, Enyu Guo, Jiehua Li, Lei Liu, Zongning Chen, Tongmin Wang

Publisher page

Abstract

TiB 2 nanoparticles were fabricated by the melt reaction between Al-10Ti and Al-3B master alloys. The reaction mechanism is ascribed to the decomposition of Al 3Ti to release free Ti atoms, which diffuse across the AlB 2/Al interface and substitute the Al atoms to form TiB 2. This substitution produces a layer of pseudo-TiB 2 on the prism planes {10‐10} AlB2 firstly, which has the same lattice structure and the similar values of the lattice parameter as AlB 2. It follows the fact that the nucleation occurs at the prism planes {10‐10}. Subsequently, the epitaxial transformation of TiB 2 particles is initiated inward the pseudo-TiB 2, which becomes detached from the substrate owing to the crystallographic mismatch between the two, thus forming the TiB 2 nanoparticles. The exposed AlB 2 prism surfaces continue to react with Ti atoms until they are totally consumed. Increasing the reaction temperature, prolonging the holding time could improve the extent of reaction, thus increasing the electrical conductivity and reducing the elastic modulus. Especially, the effects of ultrasonic vibration treatment (UVT) on the reaction process were explored. Cavitation and acoustic flow generated by UVT showed a magnificent potential for promoting the reaction in melts. Thanks to the interface reaction, nano-TiB 2 particles can be generated. The nano-TiB 2p /6201 composites produced by this method recorded significant improvement in the tensile properties.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (40)

Show source-provided references
1. Optimization of electrical conductivity and strength combination by structure design at the nanoscale in Al-Mg-Si alloys10.1016/j.actamat.2015.07.039 ↗
2. Strength-conductivity synergy in cold-drawn reduced graphene oxide (RGO)-aluminum composite wires for electrical applications10.1016/j.matdes.2021.109951 ↗
3. Study on the improvement of electrical conductivity and mechanical properties of low alloying electrical aluminum alloys10.1016/j.compositesb.2016.11.042 ↗
4. Enhancing strength-ductility synergy and mechanisms of Al-based composites by size-tunable in-situ TiB2 particles with specific spatial distribution10.1016/j.compositesb.2021.108912 ↗
5. Role of trace nanoparticles in establishing fully optimized microstructure configuration of cold-rolled Al alloy10.1016/j.matdes.2021.109743 ↗
6. Interface formation and bonding control in high-volume-fraction (TiC+TiB2)/Al composites and their roles in enhancing properties10.1016/j.compositesb.2021.108605 ↗
7. Achieving simultaneously improved tensile strength and ductility of a nano-TiB2/AlSi10Mg composite produced by cold spray additive manufacturing10.1016/j.compositesb.2020.108404 ↗
8. A heat treatable TiB2/Al-3.5Cu-1.5Mg-1Si composite fabricated by selective laser melting: microstructure, heat treatment and mechanical properties10.1016/j.compositesb.2018.04.026 ↗
9. Enhanced nanohardness and new insights into texture evolution and phase transformation of TiAl/TiB2 in-situ metal matrix composites prepared via selective laser melting10.1016/j.actamat.2017.07.003 ↗
10. Selective laser melting of nano-TiB2 decorated AlSi10Mg alloy with high fracture strength and ductility10.1016/j.actamat.2017.02.062 ↗
11. Manipulating the particle distribution of in situ TiB2p/Al composites via acoustic vibration and cooling rate10.1016/j.matlet.2019.127063 ↗
12. Development of TiB2 reinforced aluminum foundry alloy based in situ composites - Part II: enhancing the practical aluminum foundry alloys using the improved Al-5wt%TiB2 master composite upon dilution10.1016/j.msea.2014.03.021 ↗
13. On the preparation and mechanical properties of in situ small-sized TiB2/Al-4.5Cu composites via ultrasound assisted RD method10.1016/j.jallcom.2018.06.303 ↗
14. Post in-situ reaction ultrasonic treatment for generation of Al-4.4Cu/TiB2 nanocomposite: a route to enhance the strength of metal matrix nanocomposites10.1016/j.jallcom.2016.05.067 ↗
15. The grain refinement of 1070 alloy by different Al-Ti-B mater alloys and its influence on the electrical conductivity10.1016/j.rinp.2019.102482 ↗
16. Effects of grain refinement and boron treatment on electrical conductivity and mechanical properties of AA1070 aluminum10.1016/j.matdes.2015.06.149 ↗
17. The improvement of boron treatment efficiency and electrical conductivity of AA1070Al achieved by trace Ti assistant10.1016/j.jallcom.2017.11.099 ↗
18. The improvement of electrical conductivity of hypoeutectic Al-Si alloys achieved by composite melt treatment10.1016/j.jallcom.2019.02.242 ↗
19. The dynamic mechanical response of Al2O3 and TiB2 particulate reinforced aluminum matrix composites produced by in-situ reaction10.1016/S0167-577X(98)00129-3 ↗
20. Low-cycle fatigue behavior of Al-based composites containing in situ TiB2, Al2O3 and Al3Ti reinforcements10.1016/S0921-5093(03)00266-1 ↗
21. The influence of trace elements on the microstructures and properties of the aluminum conductors10.1016/j.rinp.2018.11.033 ↗
22. Thermodynamic and kinetic analyses of the removal of impurity titanium and vanadium from molten aluminum for electrical conductor applications10.1007/s11663-021-02241-3 ↗
23. Fundamental studies of ultrasonic melt processing10.1016/j.ultsonch.2018.12.028 ↗
24. The application of external fields to the manufacturing of novel dense composite master alloys and aluminum-based nanocomposites10.1007/s11661-015-2850-3 ↗
25. Production of natural and synthesized aluminum-based composite materials with the aid of ultrasonic (cavitation) treatment of the melt10.1016/S1350-4177(02)00158-X ↗
26. Improvement of particles distribution of in-situ 5 vol% TiB2 particulates reinforced Al-4.5Cu alloy matrix composites with ultrasonic vibration treatment10.1016/j.jallcom.2016.09.013 ↗
28. Sonofragmentation of molecular crystals: Observations and Modeling
29. Ultrasound radiation as a “throwing stones” technique for the production of antibacterial nanocomposite textiles10.1021/am100291w ↗
30. Ultrasonic modification of aluminum surfaces: Comparison between thermal and ultrasonic effects10.1021/jp3016408 ↗
31. Applications of ultrasound to materials chemistry10.1557/S088376940004464X ↗
32. Interfacial reaction of intermetallic compounds of ultrasonic-assisted brazed joints between dissimilar alloys of Ti-6Al-4V and Al-4Cu-1Mg10.1016/j.ultsonch.2011.03.025 ↗
33. TiB2 reinforced aluminum based in situ composites fabricated by stir casting10.1016/j.msea.2014.12.033 ↗
34. Effect of rotary electromagnetic stirring during solidification of in-situ Al-TiB2 composites10.1016/j.matdes.2016.10.007 ↗
35. Ultrasound assisted salts-metal reaction for synthesizing TiB2 particles at low temperature10.1016/j.cej.2014.11.043 ↗
36. Ultrasound-assisted liquid-phase synthesis and mechanical properties of aluminum matrix nanocomposites incorporating boride nanocrystals
37. Development of Al 6063-TiB2 in situ composites10.1016/j.matdes.2009.10.019 ↗
38. The grain refining of aluminum and phase relationships in the Al-Ti-B system10.1007/BF02645112 ↗
39. Ultrasound-assisted crystallization (sonocrystallization)10.1016/j.ultsonch.2006.12.004 ↗
40. Relationship between microstructure, properties and reaction conditions for Cu-TiB2 alloys prepared by in situ reaction10.1016/j.actamat.2009.06.030 ↗