Mechanical properties of a new kind of porous aluminum alloy composite from ceramic hollow spheres with high strength
Source abstract
Abstract
A new kind of porous 6061 aluminum alloy composite material was successfully fabricated using self-made high-strength silicon-containing ceramic hollow spheres as reinforcement. For comparison, another composite with commercial alumina hollow spheres was produced. All of these porous composite materials were produced by sintering at 650 ℃ for 2 h. Their microstructures display that the aluminum alloy reacts with the self-made ceramic hollow spheres, forming a thin transition layer containing MgO and Al 2O 3 . Moreover, it was analyzed that the influence of the different classes of ceramic hollow spheres on the properties of porous composites, including the compressive strength, specific strength and energy absorption performance. The results indicate that the self-made silicon-containing ceramic hollow sphere can help to hinder the plastic deformation of the aluminum alloy metal matrix, which makes the sample display a short yield platform where the stress remains relatively stable. As a comparison, there is no yield platform where the stress remains relatively stable in the sample with commercial alumina hollow spheres under compression. Due to the formed transition layer, the sample with the self-made ceramic hollow sphere has a significantly higher compressive strength, specific strength and energy absorption performance. Compared with the porous magnesium alloy composite, the compressive behavior of porous composite is subject to that of the metal matrix to a great extent, and the content of Mg in the matrix determines the resultants and the level of the interface reaction. In addition, the compressive strength, specific strength, and energy absorption capacity of the porous aluminum alloy composite are all significantly higher than those of the porous magnesium alloy composite.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Cellular and Composite Structures · Aluminum Alloys Composites Properties · Innovations in Concrete and Construction Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. Liu · 2014
2. Liu · 2019
3. Property relations based on the octahedral structure model with body-centered cubic mode for porous metal foams10.1016/j.matdes.2019.108413 ↗
4. Special review: mechanical investigation on failure modes of reticular porous metal foams under different loadings in engineering applications10.1108/MMMS-11-2020-0279 ↗
5. B. Sosnick, Process for making foamlike mass of metal:US2434775[P].1948-01-20.
6. J.C. Elliott, Method of producing metal foam: US, US2751289 A[P], 1956.
7. GIbson · 1997
8. Compressive properties of expanded glass and alumina hollow spheres hybrid reinforced aluminum matrix syntactic foams[J]
9. AZ91 magnesium matrix foam composites with fly ash cenospheres fabricated by negative pressure infiltration technique[J]10.1016/j.matchar.2017.04.005 ↗
10. Metal matrix syntactic foams produced by pressure infiltration—the effect of infiltration parameters[J]10.1016/j.msea.2013.06.066 ↗
11. On the sintering mechanisms and microstructure of aluminium–ceramic cenospheres syntactic foams produced by powder metallurgy route[J]10.1016/j.compositesa.2015.11.037 ↗
12. Titanium-cenosphere syntactic foam made through powder metallurgy route[J]10.1016/j.matdes.2011.07.055 ↗
13. Evaluation of wear resistance of magnesium/glass microballoon syntactic foams for engineering/biomedical applications[J]10.1016/j.ceramint.2019.01.207 ↗
14. Enhancing the ignition, hardness and compressive response of magnesium by reinforcing with hollow glass microballoons[J]10.3390/ma10090997 ↗
15. Manufacture and compression properties of syntactic foams[J]10.1016/0010-4361(93)90270-I ↗
16. Microstructure and mechanical properties of bimodal syntactic foams with different size combination and volume fraction of alumina hollow spheres[J]10.1016/j.msea.2021.141798 ↗
17. Compression properties of syntactic foams: effect of cenosphere radius ratio and specimen aspect ratio[J]10.1016/j.compositesa.2003.08.001 ↗
18. Radius ratio effect on high-strain rate properties of syntactic foam composites[J]10.1007/s10853-008-3065-4 ↗
19. Metallic syntactic foams synthesis, characterization and mechanical properties.[D]
20. Influence of particle arrangement on the compression of functionally graded metal syntactic foams[J]10.1016/j.msea.2019.138242 ↗
21. Synthesis of syntactic steel foam using mechanical pressure infiltration[J]10.1016/j.msea.2011.12.084 ↗
22. Microstructure and strength correlation of pure Al and Al-Mg syntactic foam composites subject to uniaxial compression[J]10.1016/j.msea.2017.04.060 ↗
23. Al–Al2O3 syntactic foams – part I: effect of matrix strength and hollow sphere size on the quasi-static properties of Al-A206/Al2O3 syntactic foams[J]10.1016/j.msea.2013.05.081 ↗
24. Preparation and compression performance of porous magnesium alloy composite with ceramic hollow spheres
25. Interfacial microstructure and compressive properties of Al-Mg syntactic foam reinforced with glass cenospheres[J]
26. I.N. Orbulov, A. Németh, J. Dobránszky, Manufacturing of composites by pressure infiltration, structure and mechanical properties[J], in: Proceedings of Sixth Conference on Mechanical Engineering, May 29–30, Budapest, Hungary, 2008.
27. Interface interactions during fabrication of aluminum alloy-alumina fiber composites[J]10.1007/BF02659927 ↗
28. Evaluation of cushioning properties of plastic foams from compressive measurements [J]10.1002/pen.760211505 ↗