Microstructure evolution, texture and strengthening mechanism of Al–Mg alloy with a square pyramid part during hot gas bulging with clustering balls
Source abstract
Abstract
In the present work, the method of hot gas bulging with clustering balls (HGBB) was used to investigate the microstructure evolution, texture, and strengthening mechanism of Al–Mg alloys. After an alloy sheet was heated to 450 °C for 15 min, the square-pyramid shaped part was bulged by air at a pressure of 2 MPa. The ultimate tensile strength and hardness of the formed parts increased with the deformation, and the improvements in the most deformed area were by 30% and 40%, respectively, compared with the undeformed area. Microstructural and textural characteristics revealed that dynamic recovery occurred when the effective strain was 0.36, and new grains were created through dynamic recrystallization after the strain was further increased. The grains in the Cube {100} <001> and Brass {110} <112> orientations gradually increased with the deformation. Fine-grain strengthening, second-phase strengthening, and geometrically necessary dislocation density strengthening were the main strengthening mechanisms in the deformed area, which could be enhanced by the deformation during HGBB. A high dislocation density and low-angle grain boundaries were generated, accelerating and enhancing the precipitation and formation of fine recrystallized grains. The HGBB process yielded improved formability and mechanical properties of the formed parts.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal Forming Simulation Techniques · Microstructure and mechanical properties · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. Critical life cycle inventory for aluminum die casting: a lightweight-vehicle manufacturing enabling technology10.1016/j.apenergy.2021.117814 ↗
2. Numerical simulation and experimental research on hot extrusion of 5B70 aluminum alloy complex end frame part10.1177/0954406220912280 ↗
3. Formability characteristics of AA5083 sheets under hot forming conditions10.4028/www.scientific.net/KEM.549.356 ↗
4. Machining of aluminum alloys: a review10.1007/s00170-016-8431-9 ↗
5. Effect of heat treatment conditions on mechanical properties and precipitates in sheet metal hot stamping of 7075 aluminum alloy10.1007/s11665-018-3588-z ↗
6. A review on forming techniques for manufacturing lightweight complex—shaped aluminium panel components
7. Gas forming of shallow rounded rectangular pan using aluminum alloy sheets10.1007/s00170-018-2088-5 ↗
8. The effects of pressure control technique on hot gas blow forming of Mg AZ31 sheets10.1007/s12289-018-1432-5 ↗
9. Hot metal gas forming of closed-cell aluminum foam sandwich panels10.1007/s12666-020-02027-2 ↗
10. Determination of pressurizing rate during hot gas forming with integrated heat treatment of Al–Cu–Li alloy: deformation and strengthening behaviors10.1007/s00170-020-05965-9 ↗
11. Deformation and strengthening analysis of Al-Mg-Si alloy sheet during hot gas forming with synchronous die quenching10.1016/j.jmapro.2020.07.005 ↗
12. Research on the local formability of Al-Mg-Si alloy sheet during rapid hot gas forming10.1007/s00170-020-05478-5 ↗
13. The effect of ultrafine-grained states on superplastic behavior of Al-Mg-Si alloy10.1016/j.matlet.2019.126503 ↗
14. Recent development of superplasticity in aluminum alloys: A review
15. Process optimization and microstructural development during superplastic-like forming of AA508310.1007/s00170-013-5208-2 ↗
16. Formability and microstructure of Ti22Al24.5Nb0.5Mo rolled sheet within hot gas bulging tests at constant equivalent strain rate10.1016/j.matdes.2016.06.109 ↗
17. Microstructural evolution in recrystallized and unrecrystallized Al-Mg-Sc alloys during superplastic deformation10.1016/j.msea.2012.03.076 ↗
18. Investigation on a novel hot gas bulging with the clustering balls and evaluation of performance of 5083 alloy with a square pyramid part10.1016/j.jmrt.2021.07.136 ↗
19. Experimental and numerical investigation of the mechanical behavior of the AA5383 alloy at high temperatures10.1016/j.jmatprotec.2020.116609 ↗
20. Dynamic recrystallization of AA5083 at 450 °C: the effects of strain rate and particle size10.1007/s11661-008-9476-7 ↗
21. Effect of loading direction on the deformation and annealing behavior of a zirconium alloy10.1016/j.msea.2018.08.013 ↗
22. W. Cheng, Y. Bai, S. Ma, L. Wang, H. Wang, H. Yu, Hot deformation behavior and workability characteristic of a fine-grained Mg8Sn2Zn2Al alloy with processing map, J. Mater. Sci. Technol. 35 (2019) 1198–1209. https://doi.org/10.1016/j.jmst.2018.12.001.10.1016/j.jmst.2018.12.001 ↗
23. Comparison of hot deformation behaviour and microstructural evolution for Ti-5Al-5V–5Mo-3Cr alloys prepared by powder metallurgy and ingot metallurgy approaches10.1016/j.matdes.2019.107682 ↗
24. The effects of texture on formability of aluminum alloy sheets10.1016/j.actamat.2007.04.014 ↗
25. Goss texture intensity effect on fatigue crack propagation resistance in an Al-Cu-Mg alloy10.1016/j.jallcom.2017.09.320 ↗
26. Cube recrystallization textures in a hot deformed Al-Mg-Si alloy10.1016/S1359-6462(01)01174-5 ↗
27. Cube texture in hot-rolled aluminum alloy 1050 (AA1050)-nucleation and growth behavior10.1016/j.actamat.2008.02.037 ↗
28. The origin of recrystallization textures
29. Asymmetric cold rolling of AA7075 alloy: The evolution of microstructure, crystallographic texture, and mechanical properties10.1016/j.msea.2021.141801 ↗
30. Effect of strain-induced precipitation on dynamic recrystallization in Mg-Al-Sn alloys10.1016/j.msea.2014.08.032 ↗
31. Effect of Ce addition on microstructure evolution and precipitation in Cu-Co-Si-Ti alloy during hot deformation10.1016/j.jallcom.2020.155666 ↗
32. Mechanical properties of copper/bronze laminates: role of interfaces10.1016/j.actamat.2016.06.023 ↗
33. Effect of Ti addition on microstructure evolution and precipitation in Cu–Co–Si alloy during hot deformation10.1016/j.jallcom.2019.153518 ↗
34. Determination of geometrically necessary dislocations in large shear strain localization in aluminum10.1016/j.actamat.2016.07.051 ↗
35. Precipitation behavior of Cu-3.0Ni-0.72Si alloy10.1016/j.actamat.2018.12.047 ↗
36. Effect of the number of ECAP pass time on the electrochemical properties of 1050 Al alloys10.1016/j.msea.2003.08.056 ↗
37. Optimization of aluminum alloy AA5083 for superplastic and quick plastic forming10.1007/s11661-019-05305-x ↗
38. Reactive mechanism and mechanical properties of in situ composites fabricated from an Al-TiO 2 system by friction stir processing10.1016/j.actamat.2012.09.016 ↗
39. Hall-Petch relations and strengthening of Al-ZnO composites in view of grain size relative to interparticle spacing10.1016/j.scriptamat.2018.04.042 ↗
40. Hardness-strength relationships in fine and ultra-fine grained metals processed through constrained groove pressing10.1016/j.msea.2015.03.122 ↗
41. Fabrication and characterization of a high strength ultra-fine grained metal-matrix AA8006-B4C layered nanocomposite by a novel accumulative fold-forging (AFF) process10.1016/j.matdes.2018.07.047 ↗