Plasma-sprayed lanthanum-doped strontium titanate as an interconnect for solid oxide fuel cells: Effects of powder size and process conditions
Source abstract
Abstract
Abstract As a key component of the novel bi-layer interconnect for solid oxide fuel cells (SOFC), La-doped SrTiO3 (LST) has been deposited by atmospheric plasma spraying in this study. The effects of powder particle size, hydrogen flow rate and deposition temperature on stoichiometry, microstructure, and properties of LST deposits have been systematically investigated. The preferential vaporization loss of Sr is quantified by the relationship between the droplet size and splat composition, while the droplet size prior to impact is measured by a confocal laser microscopy and the composition of splat is analyzed by the energy-dispersive spectrum of scanning electron microscopy. Thermogravimetric analysis is used to determine the oxygen non-stoichiometry of the deposit. It is found that when the droplet diameter is smaller than 30 µm, the preferential vaporization induced Sr loss is significantly increased up to 45% with decreasing particle size, while it is greatly reduced if the droplet size is larger than 30 µm. Two mechanisms including diffusion-dominated mass transfer and convection-dominated mass transfer are proposed to explain the particle size effect on Sr loss. With increasing H2 flow in plasma gas, the oxygen deficiency in LST deposit is increased. Moreover, the effective bonding at lamellar interfaces is realized by increasing the deposition temperature to higher than the critical bonding temperature. The electrical conductivity of LST deposits is remarkably improved by decreasing Sr loss, increasing oxygen vacancy concentration, and enhancing the lamellar bonding. The LST coatings prepared at a deposition temperature of 450 °C with coarse powder particles exhibits a dense microstructure and a conductivity of ~100 S/cm at 850 °C in the reducing atmosphere. The results show that by properly optimizing the process conditions, the plasma-sprayed LST coating is a promising candidate to be a part of the bi-layer interconnect for SOFCs.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advancements in Solid Oxide Fuel Cells · Electronic and Structural Properties of Oxides · Semiconductor materials and devices
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (34)
Show source-provided references
1. Progress in material selection for solid oxide fuel cell technology: a review10.1016/j.pmatsci.2015.01.001 ↗
2. Huang · 2016
3. Application of solid oxide fuel cell technology for power generation—a review10.1016/j.rser.2012.11.031 ↗
4. Kendall · 2015
5. Ferrari · 2017
6. Thermally sprayed large tubular solid oxide fuel cells and its stack: geometry optimization, preparation, and performance10.1007/s11666-016-0506-5 ↗
7. Fergus · 2016
8. La-doped SrTiO3 interconnect materials for anode-supported flat-tubular solid oxide fuel cells10.1016/j.ijhydene.2011.10.125 ↗
9. Bi-layer structures as solid oxide fuel cell interconnections10.1016/j.jpowsour.2005.02.093 ↗
10. Conductivity and expansion at high temperature in Sr0.7La0.3TiO3−α prepared under reducing atmosphere10.1007/s10832-006-3490-1 ↗
11. Thermal, electrical, and electrocatalytical properties of lanthanum-doped strontium titanate10.1016/S0167-2738(02)00140-6 ↗
12. Progress in La-doped SrTiO3 (LST)-based anode materials for solid oxide fuel cells10.1039/C3RA42666A ↗
13. Electrical conduction behavior of La, Co co-doped SrTiO3 perovskite as anode material for solid oxide fuel cells10.1016/j.ijhydene.2009.05.079 ↗
14. A novel bilayered Sr0.6La0.4TiO3/La0.8Sr0.2MnO3 interconnector for anode-supported tubular solid oxide fuel cell via slurry-brushing and co-sintering process10.1016/j.jpowsour.2010.07.088 ↗
15. A flat-tubular solid oxide fuel cell with a dense interconnect film coated on the porous anode support10.1016/j.jpowsour.2012.04.025 ↗
16. Atmospheric plasma-sprayed La0.8Sr0.2Ga0.8Mg0.2O3 electrolyte membranes for intermediate-temperature solid oxide fuel cells10.1039/C5TA01203A ↗
17. Improving atmospheric plasma spraying of zirconate thermal barrier coatings based on particle diagnostics10.1007/s11666-011-9706-1 ↗
18. Optimization of plasma-sprayed lanthanum chromite interconnector through powder design and critical process parameters control10.1007/s11666-019-00960-3 ↗
19. Effects of powder structure and size on Gd2O3 preferential vaporization during plasma spraying of Gd2Zr2O710.1007/s11666-019-00944-3 ↗
20. Microstructure, oxygen stoichiometry and electrical conductivity of flame-sprayed Sm0.7Sr0.3CoO3-δ10.1016/j.jpowsour.2009.02.016 ↗
21. Role of process conditions on the microstructure, stoichiometry and functional performance of atmospheric plasma sprayed La(Sr)MnO3 coatings10.1016/j.jpowsour.2014.02.073 ↗
22. Effect of densification processes on the properties of plasma-sprayed YSZ electrolyte coatings for solid oxide fuel cells10.1016/j.surfcoat.2004.04.086 ↗
23. Evaporated-gas-induced splashing model for splat formation during plasma spraying10.1016/j.surfcoat.2003.10.048 ↗
24. Partial evaporation of strontium zirconate during atmospheric plasma spraying10.1007/s11666-009-9360-z ↗
25. Samsonov · 2013
26. Model and powder particle heating, melting, resolidification, and evaporation in plasma spraying processes10.1115/1.2826034 ↗
27. Plasma—particle momentum and heat transfer: modelling and measurements10.1002/aic.690290210 ↗
28. Conductivity of SrTiO3 based oxides in the reducing atmosphere at high temperature10.1016/j.jallcom.2006.05.138 ↗
29. On the chemical interaction of nanoscale lanthanum doped strontium titanates with common scandium and yttrium stabilized electrolyte materials10.1016/j.ijhydene.2012.09.022 ↗
30. Stable, efficient and cost-competitive Ni-substituted Sr(Ti,Fe)O3 cathode for solid oxide fuel cell: effect of a-site deficiency10.1016/j.jpowsour.2020.227762 ↗
31. La and Sc Co-doped SrTiO3 as novel anode materials for solid oxide fuel cells10.1016/j.elecom.2008.08.017 ↗
32. Influence of through-lamella grain growth on ionic conductivity of plasma-sprayed yttria-stabilized zirconia as an electrolyte in solid oxide fuel cells10.1016/j.jpowsour.2007.10.031 ↗
33. Conditions and mechanisms for the bonding of a molten ceramic droplet to a substrate after high-speed impact10.1016/j.actamat.2016.07.057 ↗
34. Preparation of 8YSZ thin films on porous LSM by electron beam evaporation10.5796/kogyobutsurikagaku.64.681 ↗