Low-temperature high-speed extrusion of a multicomponent Mg–Bi base alloy and its heat resistance during hot tension
Source abstract
Abstract
In this work, the microstructure and room/high-temperature (RT/HT) mechanical properties of Mg-1.0Bi-1.0Mn-1.0Al-0.5Ca-0.3Zn (BMAXZ11110, wt%) alloy, subjected to extrusion at low temperature of 300 °C and high ram extrusion speed of 9 mm/s, have been systematically investigated. This alloy exhibits excellent microstructural thermo-stability during high-speed extrusion without obvious grain coarsening, especially for the edge of alloy bar. Profuse micro/nano-scale second phases (Mg 2Bi 2Ca, Al 8Mn 5 and α-Mn) and the co-segregation of Ca and Zn atoms at grain boundaries (GBs) /residual dislocations can be observed. The co-effects of nano-scale phases and solute segregation facilitate the formation of bimodal grain structure in the BMAXZ11110 alloy. At RT, it possesses high tensile yield strength (TYS, ∼ 327.1 MPa), and GB strengthening is the most primary mechanism. At 250 °C, this alloy still can maintain relatively high TYS (∼ 187.8 MPa), indicating that it also exhibits high heat resistance. Even though the contribution of GB strengthening on the TYS decreases at 250 °C, solute segregation strengthening increment makes up for its reduction to a large extent. Hence, this study will be helpful for developing a new generation of high-strength high-speed extruded Mg-Bi base alloys accompanied with good heat resistance.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (48)
Show source-provided references
1. Optimizing mechanical properties of magnesium alloys by philosophy of thermo-kinetic synergy: review and outlook10.1016/j.jma.2021.12.016 ↗
2. An investigation on microstructure, texture and formability of AZ31 sheet processed by asymmetric porthole die extrusion10.1016/j.msea.2018.02.055 ↗
3. Fabrication of Mg/Mg composite with sleeve-core structure and its effect on room-temperature yield asymmetry via bimetal casting-co-extrusion10.1016/j.msea.2019.138476 ↗
4. Evolution mechanisms of charge weld during porthole die extrusion of ZK60 Mg profile10.1016/j.jmatprotec.2021.117401 ↗
5. Extrusion limits of magnesium alloys10.1007/s11661-007-9323-2 ↗
6. Significant Improvement in extrudability of Mg–9Al–0.8Zn–0.9Ca–0.6Y Alloy Through Mischmetal Addition10.1007/s12540-020-00822-6 ↗
7. Effects of cerium addition on the microstructure, mechanical properties and hot workability of ZK60 alloy10.1016/j.msea.2012.09.026 ↗
8. Influence of Bi addition on dynamic recrystallization and precipitation behaviors during hot extrusion of pure Mg10.1016/j.jmst.2019.10.036 ↗
9. Microstructural evolution and mechanical properties of binary Mg–xBi (x = 2, 5, and 8 wt%) alloys10.1016/j.jma.2020.03.015 ↗
10. Novel Mg–Bi–Al alloy with extraordinary extrudability and high strength10.1016/j.jallcom.2020.156026 ↗
11. Comparative study of extrudability, microstructure, and mechanical properties of AZ80 and BA53 alloys10.1016/j.jma.2021.07.009 ↗
12. Enhancing tensile strength and ductility of high-speed-extruded Mg–5Bi–2Al through trace Mn addition10.1016/j.matchar.2021.111500 ↗
13. Influence of Ca addition on microstructural characteristics and mechanical properties of Mg–5Bi–3Al alloy extruded at extremely high speed10.1016/j.msea.2022.144490 ↗
14. Novel Mg-Bi-Mn wrought alloys: the effects of extrusion temperature and Mn addition on their microstructures and mechanical properties10.1016/j.jma.2021.11.028 ↗
15. A strategy to regulate the microstructure and properties of Mg-2.0Zn-1.5Mn magnesium alloy by tracing the existence of Mn element10.1016/j.jallcom.2021.161789 ↗
16. Bimodal grained Mg–0.5Gd–xMn alloys with high strength and low-cost fabricated by low-temperature extrusion10.1016/j.jallcom.2022.168008 ↗
17. Grain boundary co-segregation in magnesium alloys with multiple substitutional elements10.1016/j.actamat.2021.116749 ↗
18. A new strong and ductile multicomponent rare-earth free Mg–Bi-based alloy achieved by extrusion and subsequent short-term annealing10.1016/j.msea.2022.144309 ↗
19. Effect of Li content on microstructure, texture and mechanical behaviors of the as-extruded Mg-Li sheets10.1016/j.msea.2017.05.110 ↗
20. Unveiling the formation of basal texture variations based on twinning and dynamic recrystallization in AZ31 magnesium alloy during extrusion10.1016/j.actamat.2018.07.014 ↗
21. Effect of alloyed Ca on the microstructure and corrosion behavior of extruded Mg-Bi-Al-based alloys10.1016/j.matchar.2020.110292 ↗
22. Improvement of mechanical properties of extruded AZX912 magnesium alloy using high-temperature solution treatment10.1557/jmr.2019.281 ↗
23. Influence of aluminum content on microstructure and performance of Mg-Zn-Ca-Al-Mn magnesium alloys10.1016/j.jallcom.2023.169719 ↗
24. Designing a magnesium alloy with high strength and high formability10.1038/s41467-018-04981-4 ↗
25. Exploiting an as-extruded fine-grained Mg-Bi-Mn alloy with strength-ductility synergy via dilute Zn addition10.1016/j.jallcom.2022.166337 ↗
26. Developing a low-alloyed fine-grained Mg alloy with high strength-ductility based on dislocation evolution and grain boundary segregation10.1016/j.scriptamat.2021.114414 ↗
27. Pre-strain mediated fast natural aging in a dilute Mg-Zn-Ca-Sn-Mn alloy10.1016/j.scriptamat.2021.113924 ↗
28. Solute segregation assisted superplasticity in a low-alloyed Mg–Zn–Ca–Sn–Mn alloy10.1016/j.mtla.2020.100918 ↗
29. Mechanistic investigation on Ce addition in tuning recrystallization behavior and mechanical property of Mg alloy10.1016/j.jmst.2022.05.042 ↗
30. Designing new low alloyed Mg—RE alloys with high strength and ductility via high-speed extrusion10.1007/s12613-022-2472-x ↗
31. Simultaneously improving mechanical and anti-corrosion properties of extruded Mg-Al dilute alloy via trace Er addition10.1016/j.jmst.2022.12.014 ↗
32. Recent progress and development in extrusion of rare earth free Mg alloys: a review10.1007/s40195-018-00871-2 ↗
33. Recent advances in micro-alloyed wrought magnesium alloys: theory and design10.1016/S1003-6326(22)65907-7 ↗
34. Effects of extrusion speed on the microstructure and mechanical properties of Mg–9Al–0.8Zn–0.9Ca–0.6Y–0.5MM alloy10.1007/s12540-020-00867-7 ↗
35. Extrusion limit diagram of AZ91–0.9Ca–0.6Y–0.5MM alloy and effects of extrusion parameters on its microstructure and mechanical properties10.1016/j.jma.2021.06.002 ↗
36. Significant improvement in yield stress of Mg-Gd-Mn alloy by forming bimodal grain structure10.1016/j.msea.2020.140569 ↗
37. Development of low-alloyed and rare-earth-free magnesium alloys having ultra-high strength10.1016/j.actamat.2018.03.002 ↗
38. Fabrication of exceptionally high-strength Mg-4Sm-0.6Zn-0.4Zr alloy via low-temperature extrusion10.1016/j.msea.2021.142565 ↗
39. Effect of grain size on prismatic slip in Mg–3Al–1Zn alloy10.1016/j.scriptamat.2012.05.017 ↗
40. Exploring the Hall-Petch relation and strengthening mechanism of bimodal-grained Mg–Al–Zn alloys10.1016/j.jallcom.2020.155004 ↗
41. Effects of precipitate shape and orientation on dispersion strengthening in magnesium alloys10.1016/S1359-6462(02)00497-9 ↗
42. Mechanistic investigation of a low-alloy Mg–Ca-based extrusion alloy with high strength–ductility synergy10.1016/j.actamat.2020.01.017 ↗
43. Twin nucleation, twin growth and their effects on annealing strengths of Mg–Al–Zn–Mn sheets experienced different pre-compressive strains10.1016/j.jallcom.2019.152310 ↗
44. Enhanced strength-ductility synergy achieved through twin boundary pinning in a bake-hardened Mg–2Zn-0.5Ca alloy10.1016/j.msea.2021.142239 ↗
45. Thick grain boundary induced strengthening in nanocrystalline Ni alloy10.1039/C9NR06843K ↗
46. Grain boundary strengthening in hot rolled magnesium-5 at% thallium: Importance of texture10.1016/0036-9748(83)90088-1 ↗
47. Temperature dependent elastic coefficients of Mg2X (X=Si, Ge, Sn, Pb) compounds from first-principles calculations10.1016/j.jallcom.2010.03.153 ↗
48. Microstructure and mechanical property of a novel heat-resistant Mg-Ca-Mn based alloy10.1016/j.matchar.2022.112428 ↗