journal article·2023-10

Freeze-casted tungsten skeleton reinforced copper matrix composites

Rong Li, Wenge Chen, Kai Zhou, Yuxuan Sun, Yahui Wen, Zhe Wang, Ahmed Elmarakbi, Yong-Qing Fu

Publisher page

Abstract

Copper-tungsten (Cu-W) composites with a copper content larger than 50 vol% are expected to have a good combination of electrical conductivity and mechanical properties. However, it is difficult to synthesize these types of composites using the conventional manufacturing routes. In this paper, W skeletons with a high porosity up to 80 ± 0.8% and well-aligned microstructures were prepared by directional solidification of aqueous slurries of W followed by ice sublimation and heat treatment. Tungsten reinforced copper matrix composites (e.g., Cu-15 vol% W composites) were fabricated by infiltration of Cu into the W skeleton structures, and their microstructure, electrical conductivity and mechanical properties were studied. The synthesized Cu-15 vol% W composites exhibited alternately patterned Cu and W microstructures and showed a good combination of electrical conductivity of 78 ± 2% IACS and hardness of 136 ± 6HV. The strengthening mechanisms of these Cu-15 vol% W composites were identified as the formation of tungsten network structures which support and strengthen the copper matrix. Residual pores in the W lamellae and weak interfaces of copper-tungsten caused the initiation and propagation of cracks, and the fracture mode of Cu-15 vol% W composite was polymerization induced ductile fracture.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced materials and composites · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. Managing mechanical and electrical properties of nanostructured Cu-Fe composite by aging treatment10.1016/j.matchar.2022.112600 ↗
2. Performance improvement of laser additive manufactured Cu-Cr alloy via continuous extrusion10.1016/j.jallcom.2021.160475 ↗
3. Research status and development trend of preparation technology of ceramic particle dispersion strengthened copper-matrix composites10.1016/j.jallcom.2020.156475 ↗
4. In-situ generated graphene from wheat flour for enhancing mechanical and electrical properties of copper matrix composites10.1016/j.msea.2022.142662 ↗
5. Effect of CVD GAs flow rate on performance of graphene-reinforced copper-based composites
6. Preparation of in-situ growth three-dimensional Cu @Graphane composite by chemical vaper deposition
7. Study of the preparation and properties of 0.5 vol% Ni-CNTs/Cu nanocomposites with magnetic alignment10.1016/j.jallcom.2018.12.028 ↗
8. Effect of CNTs content on the microstructures and properties of CNTs/Cu composite by microwave sintering10.1016/j.jallcom.2018.08.315 ↗
9. Effect of spark plasma sintering temperature on structure and performance characteristics of Cu-20wt% W composite10.1016/j.jallcom.2022.165246 ↗
10. W-Cu composites with excellent comprehensive properties10.1016/j.compositesb.2022.109664 ↗
11. Uncover the mystery of interfacial interactions in immiscible composites by spectroscopic microscopy: a case study with W-Cu10.1016/j.jmst.2022.03.014 ↗
12. Effect of sintering temperature on fine-grained Cu-W composites with high copper10.1016/j.matchar.2019.04.017 ↗
13. Characterization, pore size measurement and wear model of a sintered Cu-W nano composite using radial basis functional neural network10.1016/j.matdes.2014.11.035 ↗
14. Enhanced mechanical and electrical properties of in situ synthesized nano-tungsten dispersion-strengthened copper alloy10.1016/j.msea.2020.140161 ↗
15. Enhancing copper infiltration into alumina using spark plasma sintering to achieve high performance Al2O3/Cu composites10.1016/j.ceramint.2017.09.062 ↗
16. Directionally freeze-cast titanium foam with aligned, elongated pores10.1016/j.actamat.2007.09.002 ↗
17. Porous Ti6Al4V alloys with high strength-to-modulus ratio fabricated by unidirectional freeze casting of SiC fiber containing slurry10.1016/j.msea.2021.141584 ↗
18. Structural evolution of directionally freeze-cast iron foams during oxidation/reduction cycles10.1016/j.actamat.2018.09.054 ↗
19. Porous Cu foams with oriented pore structure by freeze casting10.1016/j.matlet.2017.06.011 ↗
20. Surface-oxidized, freeze-cast cobalt foams: microstructure, mechanical properties and electrochemical performance10.1016/j.actamat.2017.09.066 ↗
21. Synthesis, structure and mechanical properties of directionally freeze-cast tungsten foams10.1557/jmr.2016.62 ↗
22. Ice-templated porous tungsten and tungsten carbide inspired by natural wood10.1016/j.jmst.2019.10.021 ↗
23. Periodic ice banding in freezing colloidal dispersions10.1021/la303458m ↗
24. Architectural control of freeze-cast ceramics through additives and templating10.1111/j.1551-2916.2009.03087.x ↗
25. Ice-templated porous alumina structures10.1016/j.actamat.2006.11.003 ↗
26. Enhanced mechanical and arc erosion resistant properties by homogenously precipitated nanocrystalline fcc Nb in the hierarchical W-Nb-Cu composite10.1016/j.compositesb.2018.11.025 ↗
27. Preparation and properties of W-30 wt% Cu alloy with the additions of Ni and Fe elements10.1016/j.jallcom.2022.167040 ↗
28. Microstructural analysis of undoped and moderately Sc-doped TiO2 anatase nanoparticles using Scherrer equation and Debye function analysis10.1016/j.matchar.2018.07.022 ↗
29. Diagrams on the standard free energy change per unit volume for the formation of oxide (surface, carbide, nitride)
30. Influence of lanthanum on enhancement of mechanical and electrical properties of Cu-Al2O3 composites10.1016/j.jre.2018.08.016 ↗
31. Anisotropic mechanical and corrosion properties of directionally solidified Mg-3Zn-0.2Ca alloy10.1016/j.jallcom.2021.162687 ↗
32. Tungsten nanoparticle-strengthened copper composite prepared by a sol-gel method and in-situ reaction10.1007/s12613-019-1889-3 ↗
33. Strengthening of copper with homogeneous dispersion of nanoscale tungsten particles fabricated by spark plasma sintering10.1016/j.msea.2021.141438 ↗
34. Strength and electrical conductivity behavior of nanoparticles reaction on new alumina dispersion-strengthened copper alloy10.1016/j.jallcom.2019.05.271 ↗
35. Investigation on microstructure and properties of Cu–Al2O3 composites fabricated by a novel in-situ reactive synthesis10.1016/j.matdes.2015.12.018 ↗
36. Microstructures and properties of Al2O3 dispersion-strengthened copper alloys prepared through different methods10.1007/s12613-016-1367-0 ↗
37. Microstructure and properties of Y2O3/Cu composites fabricated by a novel liquid phase in situ reactive synthesis process10.1016/j.ceramint.2022.06.202 ↗
38. Uniformly dispersed Y2O3 nanoparticles in nanocrystalline copper matrix via multistep ball milling and reduction process10.1016/j.matlet.2019.01.120 ↗
39. Electrical wear of TiB2 particle-reinforced Cu and Cu-Cr composites prepared by vacuum arc melting10.1016/j.vacuum.2020.109295 ↗
40. Preparation and properties of copper matrix composites synergistically strengthened by Al2O3 and CPD10.1016/j.diamond.2022.108916 ↗
41. Improving comprehensive performance of copper matrix composite by spray pyrolysis fabricated CNT/W reinforcement10.1016/j.jallcom.2020.154940 ↗
42. Investigation on microstructure and properties of TiC0.5-Al2O3/Cu composites fabricated by a novel in-situ reactive synthesis10.1016/j.ceramint.2021.03.225 ↗