Study on the micro-structure and the nano-indentation responses of laser solid formed epitaxial Ni-based superalloy
Source abstract
Abstract
Laser solid forming (LSF) is one of the most promising technologies which has been extensively applied for the reshape and fabrication of the thermal parts in gas turbine and aero-engine. In this paper, the Ni-based single crystal superalloy thin-walled parts were prepared by using the LSF technology. Then, the electron back-scatter diffraction (EBSD) and the scanning electron microscope (SEM) technologies were employed to characterize the micro-structure morphology and crystallographic orientation of grains. The dislocation density of Ni-based superalloy thin-walled parts was analyzed. The results showed that a remarkable micro-structure gradient with respect to different heights of repaired Ni-based superalloy thin-walled parts was observed after the LSF process while the micro-structure distribution in width direction is comparatively more uniform. In addition, the misorientation of crystallographic orientation can be attributed to the dislocation density. A higher dislocation density contributes to aggregation of massive low angle grain boundaries (LAGBs) and formation of high angle grain boundaries (HAGBs), which in return conversely reduces dislocation density within the material. Finally, the mechanical properties of the LSF epitaxial Ni-based superalloy were investigated by the cyclic creep and Nano-indentation tests. The results showed that with the increasing of repair height, the residual indentation depth increased, while the elastic modulus increased first and then decreased. Meanwhile, a lower hardness of the stray grain region was obtained comparing with that of the substrate. Within the stray grain region, the hardness decreases along the building direction.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (22)
Show source-provided references
1. HAZ liquation cracking mechanism of IN-738LC superalloy prepared by laser solid forming10.1007/s11661-018-4826-6 ↗
2. Microstructural evolution of nickel-based single crystal superalloy fabricated by directed energy deposition during heat treatment
3. Epitaxial laser deposition of single crystal Ni-based superalloys: Repair of complex geometry
4. Microstructure evolution behavior of DD6 single crystal superalloy at different using temperatures
5. A synchrotron study of microstructure gradient in laser additively formed epitaxial Ni-based superalloy10.1038/srep14903 ↗
6. The microstructure evolution and strengthening mechanism of a γ’-strengthening superalloy prepared by induction-assisted laser solid forming10.1016/j.jallcom.2018.11.386 ↗
7. A synchrotron study of defect and strain inhomogeneity in laser-assisted three-dimensionally-printed Ni-based superalloy10.1063/1.4934839 ↗
8. Influence of processing parameters on deposition characteristics of Inconel 625 superalloy fabricated by laser solid forming10.1007/s11771-021-4675-0 ↗
9. Controlling microstructural and mechanical properties of direct laser deposited Inconel 718 via laser power
10. Boosting wear properties of Inconel718 superalloy by uniform dispersing graphene nanoplatelets through laser melting deposition
11. Design and development of a high-performance Ni-based superalloy WSU 150 for additive manufacturing10.1016/j.jmst.2020.01.041 ↗
12. Microstructure and tensile properties of in939 repaired zone by laser additive remanufacturing
13. Multiscale microstructural heterogeneity and mechanical property scatter in Inconel 718 produced by directed energy deposition
14. Hardness and microstructural inhomogeneity at the epitaxial interface of laser 3D-printed Ni-based superalloy
15. Direct laser metal deposition of René 108 single crystal superalloy
16. Mechanism of heat affected zone cracking in Ni-based superalloy DZ125L fabricated by laser 3D printing technique10.1016/j.matdes.2018.04.032 ↗
17. Influence of the laser source pulsing frequency on the direct laser deposited Inconel 718 thin walls
18. Coupled heat transfer, fluid flow and solidification kinetics for laser additive manufacturing applications10.1016/j.jmapro.2021.05.019 ↗
19. Effects of process parameters on microstructure and cracking susceptibility of a single crystal superalloy fabricated by directed energy deposition10.1016/j.matdes.2020.109296 ↗
20. Bi-crystal competitive growth in a nickel-based superalloy during cell/dendrite directional solidification
21. Dislocation evolution analysis of hot compressively deformed TA10 titanium alloy based on XRD
22. Study on dislocation density change during cold roll-beating of 40Cr